• Journal of Communications and Networks
• /
• v.5 no.1
• /
• pp.73-81
• /
• 2003

The controlled load service defined within the IETF's Integrated Services architecture for quality-of-service (QoS) in the Internet requires source nodes to regulate their traffic while the network, in combination with an admission control strategy, provides a guarantee of performance equivalent to that achieved in a lightly loaded network. Packets sent in violation of the traffic contract are marked so that the network may assign them a lower priority in the use of bandwidth and buffer resources. In this paper, we define the requirements of a scheduler serving packets belonging to the controlled load service and present a novel scheduler that exactly achieves these requirements. In this set of requirements, besides efficiency and throughput, we include an additional important requirement to bound the additional delay of unmarked packets caused due to the transmission of marked packets while dropping as few marked packets as possible. Without such a bound, unmarked packets that are in compliance with the traffic contract are not likely to experience delays consistent with that in al lightly loaded network. For any given desired bound ${\alpha}$ on this additional delay, we present the CL(${\alpha}$) scheduler which achieves the bound while also achieving a per-packet work complexity of O(1) with respect to the number of flows. We provide an analytical proof of these properties of the CL(${\alpha}$) scheduler, and we also verify this with simulation using real traces of video traffic. The scheduler presented here may be readily adapted for use in scheduling flows with multi-level priorities such as in some real-time video streams, as well as in other emerging service models of the Internet that mark packets to identify drop precedences.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.151-156
• /
• 2000

The brake system is important to stop train safely. The train is sloped by regenerative brake and pneumatic brake which are continuously blended at service brake. When service is applied to train, it is controlled by train weight and brake command. The jerk limitation function is applied for impulseless smoothing braking. All brake applications in service condition have a function of the variable load control to keep the braking effort in proportion to each car load. All of control function are performed by brake controller. Therefore, we will propose the design of brake control system in order to control efficiently

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.7
• /
• pp.1263-1269
• /
• 2009

Stable and sustainable power supply means maintaining a certain level of power quality and service while securing energy resource and resolving environmental issues. Distributed generation (DG) has become an essential and indispensable element from environmental and energy security perspectives. It is known that voltage violation is the most important constraint for load variation and the maximum allowable DG. In distribution system, sending voltage from distribution substation is regulated by ULTC (Under Load Tap Changer) designed to maintain a predetermined voltage level. ULTC is controlled by LDC (Line Drop Compensation) method compensating line voltage drop for a varying load, and the sending voltage of ULTC calls for LDC parameters. The consequence is that the feasible LDC parameters considering variation of load and DG output are necessary. In this paper, we design each LDC parameters determining the sending voltage that can satisfy voltage level, decrease ULTC tap movement numbers, or increase DG introduction. Moreover, the maximum installable DG capacity based on each LDC parameters is estimated.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.433-433
• /
• 2000

In this paper, we propose a development of internet teleoperation method applying QoS model, which has the real time control capability and the time-delay predicting capability, The QoS model gives a constant bandwidth to a specified application and makes the dynamically irregular time-delay to be predictable and fined so that it can have real-time capability.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.9
• /
• pp.36-48
• /
• 1999

Controlled transfer (CT) service has been recently proposed as a new ATM transfer capability for high-speed data applications, which used a credit-based flow control. This paper investigates buffer allocation schemes for CT service and proposes an improved dynamic bugger allocation scheme. In order to improve the responsiveness to a congestion, the proposed method is considered the load factor of a link when determining the amounts of virtual connection (VC)s buffer allocation. Also, in this paper we compare the performance of the proposed method with those of the existing buffer allocation methods such as flow controlled virtual channels (FCVC) and zero queueing flow control (ZQFC) through simulation. Simulation results show tat the proposed scheme exhibits a better performance than the existing schemes in terms of throughput, fairness, queue length and link utilization.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1088-1090
• /
• 2001

In general, Power SCR(Silicon Controlled Rectifier) is most widely used in Power Plant as well as Industrial field. It has been controlled and operated according to its own control method. Especially, in case of Power plant, it plays a major role in AVR(Automatic Voltage Regulator) or electro chlorination control circuits. Generally, they used in Analog control system at above field. But each SCR current value is different because of load unbalance or switching characteristic variations, it may cause power plant unit trip or system disorder according to SCR element burn out or bad operating condition. Therefore, in this paper a development of 3 phase current balance control unit is described, it gets over the past analog control system limit, uses DSP(Digital signal processor) had high speed response, controls SCR gate firing angle for 3 phase current balance.

• Journal of Korean Institute of Industrial Engineers
• /
• v.34 no.2
• /
• pp.140-150
• /
• 2008

Point Coordination Function (PCF) of the IEEE 802.11 protocol providing a centrally-controlled polling-based multiple access to a wireless channel is very efficient in high load conditions. However, its performance degrades with increasing the number of terminals and decreasing the load, because of wastes related to unsuccessful polling attempts. To solve the problem, we propose and study analytically the generic dynamic polling policy using backoff concept. For this aim, we develop Markov models describing the network queues changes, what allows us to estimate such performance measures as the average MAC service time and the average MAC sojourn time, to show the dynamic polling efficiency and to tune optimally the backoff rule.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.53-56
• /
• 2002

In this paper, we study the network structure that can guarantee the end-to-end quality of service in the Explicit multicast network. In order to guarantee the end-to-end quality of service, we adopt the end-to-end measurement based admission control (EMBAC) scheme. For the effective measurement of the network state and minimum influence on the current data traffic, the queue structure, which the drop precedence in assured forwarding (AF) Per hop behavior (PHB) of the differentiated service (Diffserv) is applied to, is proposed. Through a simulation, we show that EMBAC can make tile controlled load service in tile AF PHB applied Xcast network, and the qualify of the admitted traffic is guaranteed. In addition, the performance of the EMBAC is changing according to the selling parameter of AF PHB.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.98-105
• /
• 2018

Cracks in RC members occurred as a result of material and structural factors. The crack width and a crack location are very difficult to examine. A direct crack control method and indirect crack control method to control a crack are presented in the KHBDC (LSD) and KSCDC (2012). In the KSCDC text, cracks are controlled by steel spacing indirectly under a service load. On the other hand, in the KSCDC appendix, cracks are controlled by a crack width directly under a sustained load. In particular, the loading state considered is different. On the other hand, cracks are controlled under a combination of service load and an effective elastic modulus is used in KHBDC. Therefore, in this study, an effective elastic modulus that can reflect the ratio of the sustained load and live load was applied, and a maximum steel spacing was calculated through a design crack width. A variable interpretation was carried out, and a rational crack control method was assessed. As a result, a steel spacing through the design crack width in the KSCDC was smaller than that from the design crack width in the KHBDC, which leads to a conservative design. In addition, the maximum steel spacing suggested in this study has a consistency eliminating the difference between direct crack control and indirect crack control.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1091-1093
• /
• 2001

The power semiconductor is widely used in the power plant or industrial field because of genealization and enlargement. It has been controlled and operated according to its own control method. Especially in case of Power plant, it plays a major role in AVR(Automatic Voltage Regulator) or electro chlorination control circuits. Generally, they used in Analog control system at above field. But each SCR current value is different because of load unbalance or switching characteristic variations, it may cause power plant unit trip or system disorder according to SCR element burn out or bad operating condition. Therefore, in this paper a development of 3 phase current balance control algorithm is described. it gets over the past analog control system limit, controls SCR gate firing angle for 3 phase current balance.