• 자원환경지질
• /
• 제49권1호
• /
• pp.23-30
• /
• 2016

자연산 로소나이트(Ca-Lawsonite, $CaAl_2Si_2O_7(OH)_2{\cdot}H_2O$) 분말의 압력증가에 따른 변화와 구조적 특성을 소형 압력 발생장치인 다이아몬드 앤빌셀과 실시간 싱크로트론 X-선 회절실험을 통하여 확인하였다. 본 연구에서 시료에 적용한 압력은 1 기압에서 8 GPa 까지였으며 메탄올, 에탄올, 물의 혼합 용액을 압력 매개체로 하여 상온조건에서 실험하였고, 특이한 상전이나 압력하 부피변화의 이상현상은 발견되지 않은 가역적 압축특성을 관찰하였다. 최고압력까지 로소나이트는 결정성을 잃지 않는 것으로 확인되었고 압력증가에 따른 체적감소를 통해 체적탄성률($B_0$)을 계산해 본 결과 146(6) GPa로 도출되었다. 체적탄성률과 함께 계산된 선형압축률은 a-, b-, c-축에서 각각 0.0022, 0.0024, $0.0020GPa^{-1}$로 압력에 의한 부피감소는 대체적으로 3축이 같은 비율로 감소하는 것을 확인하였다.

• 한국광물학회지
• /
• 제31권4호
• /
• pp.277-285
• /
• 2018

상온에서 남동석($Cu_3(CO_3)_2(OH)_2$)에 대한 고압 거동 연구를 하였다. 대칭형 다이아몬드 앤빌기기를 이용하여 21.52 GPa까지 압력을 증가시키면서 각분산 X-선 회절법과 방사광을 이용하여 고압회절 데이터를 얻었으며, 시료에 가해준 압력은 루비 형광파의 파장 변화를 측정하여 결정하였다. 본 실험에서 시행한 압력의 범위 내에서 상변이는 관찰되지 않았으며, 정압상태에서 체적탄성률($K_0$)은 ${K_0}^{\prime}$이 4일 때, 54.4 GPa로 계산되었다. 상온상태에서 얻은 남동석의 체적탄성률에 대한 신뢰도를 정규화압력 및 정규화응력변형 분석을 통해 검증하였다.

• 지질공학
• /
• 제18권4호
• /
• pp.371-379
• /
• 2008

본 연구에서는 경기도 일대의 편마암지역 11곳에서 다운홀(down-hole) 탄성파탐사를 이용하여 획득한 탄성파속도를 이용, 편마암지역에서의 탄성파 속도와 동탄성계수와의 상관성을 조사하였다. 연구결과 편마암에서의 탄성파속도의 특성은 $V_s=0.5589{\times}V_p$ 상관관계를 보여준다. 탄성파 속도와 동탄성계수와의 상관관계는 두 개의 군으로 분리된다. 풍화가 진행됨에 따라 첫 번째 군은 암석의 비중에 큰 영향을 받지만 두 번째 군에서는 절리면의 간격에 영향을 받는다. 풍화가 진행됨에 따라 첫 번째 군은 감소하는 경향을 보인다. 경암반에서의 압축파속도($V_p$) 동탄성계수($E_d$, $G_d$, $K_d$)의 상관관계는 선형으로 분석되었지만, 보통암반에서의 압축파속도($V_p$)와 동탄성계수($E_d$, $G_d$, $K_d$)의 상관관계는 2차 함수 포물선 곡선의 형태를 띠는 것으로 분석되었다. 전단파속도($V_s$)와 동탄성계수($E_d$, $G_d$, $K_d$)의 상관관계 또한 압축파속도($V_p$)와 유사한 결과를 보이는 것으로 분석되었다.

• 광물과 암석
• /
• 제35권3호
• /
• pp.367-376
• /
• 2022

본 연구는 섭입대 환경에서 다양한 액체들과 제올라이트와의 반응을 이해하기 위한 선행단계로, 섭입대 내 대표 제올라이트 중 하나인 스틸바이트(NaCa₄(Al₉Si₂₇)O₇₂·28(H₂O))의 압축거동을 관찰하였다. 물과 NaHCO₃ 용액을 매개체로 사용하였으며, 상압에서 최대 2.5 GPa까지 가압하였다. 1.0 GPa 이하에서는 두 실험 모두 0.001~0.004 GPa^-1 범위의 낮은 선형압축률과 220(1) GPa의 높은 체적탄성률을 보였다. 이는 물분자 또는 양이온이 스틸바이트의 채널 내부로 유입되면서 구조가 매우 치밀해졌기 때문으로 추측된다. 반면, 1.0 GPa 이상에서는 두 실험의 경향이 다르게 관찰되었다. 물의 실험에서는 c축, NaHCO₃의 실험에서는 b, c축의 선형압축률이 모두 0.006(1) GPa^-1으로 급격하게 증가하였다. 체적탄성률은 물과 NaHCO₃의 실험에서 각각 40(1), 52(7) GPa의 값을 보여, 1.0 GPa 이전과 비교했을 때 압축률이 4배 이상 높아졌다. 이는 1.0 GPa 이상의 압력에서 압력매개체 내 물이 얼기 시작하면서 스틸바이트 내부로 유입이 멈추었고, 단지 채널 내에서 양이온 및 물분자가 이동함에 따라서 생기는 현상으로 판단된다. 특히 NaHCO₃의 실험에서는 소듐 양이온이 치환됨에 따라 구조 내부의 분포가 달라졌을 것으로 추측되며, 이는 (001)과 (020)피크의 상대강도 비율이 물의 실험과 다른 경향으로 나타난 것을 근거로 예상해볼 수 있다.

• 한국세라믹학회지
• /
• 제13권1호
• /
• pp.35-44
• /
• 1976

The effect of quartz which exists in clays, especially in kaolin used for the production of chamotte sagger, on the strength of refractory was examined. In this study, a mixture of chamotte 50%, kaolin 25%, plastic clay 25% in ternary component system was selected as a batch composition. To this mixture 1%, 3% and 5% of feldspar and sericite were added respectively. The plastic clay used here was separated under 170 mesh by dry process. Feldspar and sericite were separated under 325 mesh by dry process. Feldspar and sericite were separated under 325 mesh by dry process. In order to change the particle size and the content of quartz, the kaolin was separated under 60, 115, 170 and 325 mesh by wet process, substituted quartz for coarse parts of it. Chamotte was classified into three grades, coarse (5-10mesh): medium (10-20mesh): fine(20-115mesh) and the ratio was 1:1:1. Samples were formed in 0.8xIx10cm size with 12.5% water at 160kg/$\textrm{cm}^2$ pressure, and fired at 130$0^{\circ}C$ for 1 hr. The fired samples were ivnestigated by means of x-ray diffraction analysis and microscopic observation, and the physical properties of them were also examined, such as firing shrinkage, apparent specific gravity and bulk specific gravity, apparent porosity, water absorption and modulus of rupture. The obtained results are as follows: 1. When screened kaolin with low content of quartz was added to fixed chamotte-plastic clay system, the sample lowered modulus of rupture and increased apparent porosity as the size of kaolin became finer. 2. When kaolin under 325 mesh with 7.2-15.81% quartz between 60-325 mesh was added to fixed chamotte-plastic clay system, the sample had higher apparent porosity and lower modulus of ruputure as the size and the amount of quartz became larger. 3. The addition of feldspar and sericite to chamotte-plastic clay system improved apparent porosity and modulus of rupture. The effect of feldspar was better when quartz content was low, although that of sericite was better than quartz content was high.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회 3차
• /
• pp.129-134
• /
• 2010

This paper investigates effects of rubber inclusion on the strength and physical characteristics of rubber.added composite geomaterial (CGM) in which dredged soils, crumb rubber, and bottom ash are reused for recycling. Several series of test specimens were prepared at 5 different percentages of rubber content (i.e. 0%, 25%, 50%, 75%, and 100% by weight of the dry dredged soil) and three different percentages of bottom ash content (i.e. 0%, 50% and 100% by weight of the dry dredged soil). The mixed soil specimens were subjected to unconfined compression test and elastic wave test to investigate their unconfined compressive strengths and small strain properties. The values of bulk unit weight of the CGM with bottom ash content of 0% and 100% decrease from 14kN/$m^3$ to 11kN/$m^3$ and 15kN/$m^3$ to 12kN/$m^3$, respectively, as rubber content increases, because the rubber had a specific gravity of 1.13. The test results indicated that the rubber content and bottom ash content were found to influence the strength and stress-strain behavior of CGM. Overall, the unconfined compressive strength, and shear modulus were found to decrease with increasing rubber content. Among the samples tested in this study, those with a lower rubber content exhibited sand-like behavior and a higher shear modulus. Samples with a higher rubber content exhibited rubber-like behavior and a lower shear modulus. The CGM with 100% bottom ash could be used as alternative backfill material better than CGM with 0% bottom ash. The results of elastic wave tests indicate that the higher rubber content, the lower shear modulus (G).

• Preventive Nutrition and Food Science
• /
• 제17권3호
• /
• pp.203-209
• /
• 2012

The effects of variable moisture content, screw speed and barrel temperature on the physicochemical properties of red ginseng powder extrudates were investigated. The raw red ginseng powders were processed in a co-rotating intermeshing twin-screw extruder. Primary extrusion variables were feed moisture content (20 and 30%), screw speed (200 and 250 rpm) and barrel temperature (115 and $130^{\circ}C$). Extruded red ginseng showed higher crude saponin contents (6.72~7.18%) than raw red ginseng (5.50%). Tested extrusion conditions did not significantly affect the crude saponin content of extrudates. Increased feed moisture content resulted in increased bulk density, specific length, water absorption index (WAI), breaking strength, elastic modulus and crude protein content and decreased water solubility index (WSI) and expansion (p<0.05). Increased barrel temperature resulted in increased total sugar content, but decreased reducing sugar content in the extrudate (p<0.05). Furthermore, increased barrel temperature resulted in increased amino acid content and specific length and decreased expansion and bulk density of extrudates only at a higher feed moisture content. The physicochemical properties of extrudates were mainly dependent on the feed moisture content and barrel temperature, whereas the screw speed showed a lesser effect. These results will be used to help define optimized process conditions for controlling and predicting qualities and characteristics of extruded red ginseng.

• 한국분말재료학회지
• /
• 제13권2호
• /
• pp.102-107
• /
• 2006

Recycling industrial wastes such as fly ash from a coal burning heat power plant and shell from an oyster farming were investigated to prevent environment contamination as well as to enhance the value of recycling materials. In this study, the lightweight aggregates and the red bricks were fabricated from fly ashes with other inorganic materials and wastes. The starting materials of the lightweight aggregate were fly ash powder and water glass, and the compacts of these materials were heat treated at $1100^{\circ}C$. The fabricated lightweight aggregates had low bulk density, $0.9-1.2\;g/cm^3$, hence floated on the water and had the strength of 7.0-11.0 MPa and the modulus of 2900-3300 MPa which indicates it has enough strength as the aggregate. Another type of the light weight aggregate was prepared from fly ashes, shell powders and clays. The bulk density, porosity, and compressive strength of these aggregates were $1.19-1.34\;g/cm^3,\;18.3{\sim}56.1%$ and 5-12 MPa, respectively. The addition of a small amount of fly ash powder prevented hydration of the light weight aggregates. The red brick was also fabricated from the fly ash containing materials. It is suitable for the brick facing of a building as it has moderate strength and low water absorption rate.

• 한국세라믹학회지
• /
• 제21권4호
• /
• pp.366-372
• /
• 1984

Unstabilized Zirconia was added to basic composition under 44$mu extrm{m}$ of 57.80wt% Clay-22.20wt% Chamotte-20.00wt% Agalmatolite system. Here the amount and the particle size of Zirconia were 5-25wt% and -20${\mu}{\textrm}{m}$ respectively and the body of these composition was first at 135$0^{\circ}C$. The results obtained from examining the properties of sintered body were as follows. 1. Firing linear shrinkage apparent density and bulk density apparent porosity and water absorption of the samples had the tend to increase according as the particle size of zirconia became larger and the amount of zirconia increased. 2. Modulus of rupture was inversely proportional to the particle size and the additive amount of zirconia, . Especially in case that the particle size of zirconia over 5${\mu}{\textrm}{m}$ and the additive amount of zirconia was 25wt% the modulus of rupture had shrunk drastically. 3. The maximum value of KIC was obtained at 20wt% additive amount of zirconia according to the each particle size of zirconia. Especially the highest value of KIC is 2, 173 M. Pa. M1/2 when the particle size of zirconia is 5~10${\mu}{\textrm}{m}$ and the additive amount is 20wt%.

• 한국정밀공학회지
• /
• 제26권7호
• /
• pp.91-98
• /
• 2009

A reliable tensile test technique for PDP's barrier rib materials was introduced. A tensile specimen was prepared by punching out of green sheet, curing the specimen in a high temperature furnace, attaching sand paper tabs on each grip ends, and then attaching two strain gages for the strain monitoring and specimen alignment. Preliminary tensile tests were successfully done with the specimens made from ZnO-based lead-free green sheet. The specimens cured at 3 different maximum curing temperatures were tested to demonstrate the applicability of the test method. The Young's modulus was 88 ${\pm}$ 4 GPa regardless of the maximum curing temperature. The ultimate tensile strength was decreased with increasing the temperature. The tensile test method proposed in this study was proven to be reliable, useful and easy to estimate the bulk mechanical properties of barrier rib materials.