• Food Engineering Progress
• /
• v.14 no.2
• /
• pp.166-172
• /
• 2010

The extraction of polyphenol and flavonoid from citrus peel was performed by the ethanol, sugar, hot water (80$^{\circ}C$), and subcritical water extraction methods. The maximum yields of total polyphenolic compounds (27.25${\pm}$1.33 mg QE/g DCP, QE and DCP indicate quercetin equivalent and dried citrus peel, respectively) and flavonoids (7.31${\pm}$0.41 mg QE/g DCP) were obtained by subcritical water extraction (SWE) with operating conditions of 190$^{\circ}C$, 1300 psi, and 10 min. The yields by SWE were over 7.2-, and 8.5-fold higher than those of total polyphenols (3.79${\pm}$0.73 mg QE/g DCP) and flavonoids (0.86${\pm}$0.27 mg QE/g DCP) obtained using the ethanol extraction, which showed the highest extraction efficiency among tested conventional methods, respectively. Antioxidant activities of extracts obtained by different methods showed no significant differences. However, the relative antioxidant yield per 1 g dried citrus peel by SWE (190$^{\circ}C$, 10 min) was over 9.5-fold higher than that by the ethanol extraction.

• Clean Technology
• /
• v.25 no.3
• /
• pp.223-230
• /
• 2019

This research was performed to evaluate the characteristics of food waste from 5 areas in Gangwon Province, Korea and to predict the $CH_4$ gas production rate. Food wastes were sampled in July and September, 2017. The amount of methane gas generation was evaluated through the biochemical methane potential (BMP) test and a calculation method using chemical composition. Average bulk density and pH of the food wastes were in the range of $0.758{\sim}0.850g\;cm^{-3}$ and 4.29 ~ 4.75, respectively. By physical composition, vegetables were the highest with 56.43 ~ 72.81% with fruits recording 5.31 ~ 8.95%, cereals 1.60 ~ 18.73%, fish and meat 4.47 ~ 12.11%, and filtrate 1.76 ~ 3.64%. The average water content was 69.30 ~ 75.87%, and VS and ash content were 22.50 ~ 27.98% and 1.63 ~ 2.48%, respectively. In addition, $BOD_5$, $COD_{Cr}$, and $COD_{Mn}$ were in the ranges of $17,690.3{\sim}33,154.9mg\;L^{-1}$, $106,212.3{\sim}128,695.5mg\;L^{-1}$, and $51,266.1{\sim}63,426.3mg\;L^{-1}$, respectively. The NaCl content ranged from 0.81 to 1.17%. The results of elemental analysis showed that the contents of C, H, O, N, and S were 44.87 ~ 48.1%, 7.12 ~ 7.57%, 40.13 ~ 43.78%, 3.22 ~ 4.14%, and 0.00 ~ 0.02%, respectively. In a comparison of the methane production yield per VS mass of food waste, there was no significant difference between the cumulative amount (${0.303{\sim}0.354m_{CH4}}^3\;{kg_{VS}}^{-1}$) by the BMP test and the theoretical amount (${0.294{\sim}0.352m_{CH4}}^3\;{kg_{VS}}^{-1}$) calculated by chemical composition.

• Journal of Life Science
• /
• v.29 no.11
• /
• pp.1227-1234
• /
• 2019

Prunus mume, also known as maesil, is a popular fruit consumed in East Asia (Korea, Japan, and China). It contains high amounts of organic acids, minerals, and polyphenols and has been used as a medication for fever, vomiting, and detoxification. In this study, the anti-proliferative and apoptotic effects of solvent fractions from maesil were evaluated using sulforhodamine B (SRB) assays, morphological evaluations, Hoechst 33258 staining, and western blotting. Addition of the maesil methanol fraction (MMF) and the maesil butanol fraction (MBF) significantly and dose-dependently decreased the cell viability of HT-29 human colon cancer cells. Colony-forming assays confirmed that the MMF and MBF treatments decreased colony numbers when compared with untreated control cells. Treatment of HT-29 cells with MMF and MBF caused a distortion of the cell morphology to a shrunken cell mass. Treatment with MMF and MBF also dose-dependently increased nuclear condensation and the formation of apoptotic bodies in HT-29 cells. Treatment with MMF and MBF significantly and dosedependently increased the expression of Bax (a pro-apoptotic protein), caspase-3, and poly ADP-ribose polymerase (PARP) and decreased the expression of Bcl-2 (an anti-apoptotic protein). MMF significantly and dose-dependently inhibited cell proliferation induced by bisphenol A, an environmental hormone. Therefore, MMF may have potential use as a functional food and as a possible therapeutic agent for the prevention of colon cancer.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.86-92
• /
• 2022

Recently, the bio-healthcare market is enlarging worldwide due to various reasons such as the COVID-19 pandemic. Among them, biometric measurement and analysis technology are expected to bring about future technological innovation and socio-economic ripple effect. Existing systems require a large-capacity battery to drive signal processing, wireless transmission part, and an operating system in the process. However, due to the limitation of the battery capacity, it causes a spatio-temporal limitation on the use of the device. This limitation can act as a cause for the disconnection of data required for the user's health care monitoring, so it is one of the major obstacles of the health care device. In this study, we report the concept of a standalone healthcare monitoring module, which is based on both triboelectric effects and electromagnetic effects, by converting biomechanical energy into suitable electric energy. The proposed system can be operated independently without an external power source. In particular, the wireless foot pressure measurement monitoring system, which is rationally designed triboelectric sensor (TES), can recognize the user's walking habits through foot pressure measurement. By applying the triboelectric effects to the contact-separation behavior that occurs during walking, an effective foot pressure sensor was made, the performance of the sensor was verified through an electrical output signal according to the pressure, and its dynamic behavior is measured through a signal processing circuit using a capacitor. In addition, the biomechanical energy dissipated during walking is harvested as electrical energy by using the electromagnetic induction effect to be used as a power source for wireless transmission and signal processing. Therefore, the proposed system has a great potential to reduce the inconvenience of charging caused by limited battery capacity and to overcome the problem of data disconnection.

• Clean Technology
• /
• v.28 no.1
• /
• pp.24-31
• /
• 2022

Petroleum-based plastics are used for various purposes and pose a significant threat to the earth's environment and ecosystem. Many efforts have been taken globally in different areas to find alternatives. As part of these efforts, this study manufactured alginate-based polyvinyl alcohol (PVA) blended films by casting from an aqueous solution prepared by mixing 10 wt% petroleum-based PVA with biodegradable, marine biomass-derived alginate. Glutaraldehyde was used as a cross-linking agent, and cardanol, an alkyl phenol-based bio-oil extracted from cashew nut shell, was added in the range of 0.1 to 2.0 wt% to grant antibacterial activity to the films. FTIR and TGA were performed to characterize the manufactured blended films, and the tensile strength, degree of swelling, and antibacterial activity were measured. Results obtained from the FTIR, TGA, and tensile strength test showed that alginate, the main component, was well distributed in the PVA by forming a matrix phase. The brittleness of alginate, a known weakness as a single component, and the low thermal durability of PVA were improved by cross-linking and hydrogen bonding of the functional groups between alginate and PVA. Addition of cardanol to the alginate-based PVA blend significantly improved the antibacterial activity against S. aureus and E. coli. The antibacterial performance was excellent with a death rate of 98% or higher for S. aureus and about 70% for E. coli at a contact time of 60 minutes. The optimal antibacterial activity of the alginate-PVA blended films was found with a cardanol content range between 0.1 to 0.5 wt%. These results show that cardanol-containing alginate-PVA blended films are suitable for use as various antibacterial materials, including as food packaging.

• Clean Technology
• /
• v.28 no.4
• /
• pp.269-277
• /
• 2022

With the recent development of the biological enzymatic reaction industry, lactic acid (LA) can be mass-produced from biomass sources. In particular, a catalytic process that converts LA into acrylic acid (AA) is receiving much attention because AA is used widely in the petrochemical industry as a monomer for superabsorbent polymers (SAP) and as an adhesive for displays. In the LA conversion process, NaY zeolites have been previously shown to be a high-activity catalyst, which improves AA selectivity and long-term stability. However, NaY zeolites suffer from fast deactivation due to severe coking. Therefore, the aim of this study is to modify the acid-base properties of the NaY zeolite to address this shortcoming. First, base promoters, Ca ions, were introduced to the NaY zeolites to tune their acidity and basicity via ion exchange (IE) and incipient wetness impregnation (IWI). The IWI method showed superior catalyst selectivity and stability compared to the IE method, maintaining a high AA yield of approximately 40% during the 16 h reaction. Based on the NH₃- and CO₂-TPD results, the calcium salts that impregnated into the NaY zeolites were proposed to exit as an oxide form mainly at the exterior surface of NaY and act as additional base sites to promote the dehydration of LA to AA. The NaY zeolites were further treated with KOH before calcium impregnation to reduce the total acidity and improve the dispersion of calcium through the mesopores formed by KOH-induced desilication. However, this KOH treatment did not lead to enhanced AA selectivity. Finally, calcium loading was increased from 1wt% to 5wt% to maximize the amount of base sites. The increased basicity improved the AA selectivity substantially to 65% at 100% conversion while maintaining high activity during a 24 h reaction. Our results suggest that controlling the basicity of the catalyst is key to obtaining high AA selectivity and high catalyst stability.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.25 no.4
• /
• pp.118-126
• /
• 2024

Recently, the alternative meat (food) market is growing rapidly due to the increase in meat consumption due to global population growth and income improvement, as well as issues such as equal welfare, carbon neutrality, and sustainability. The government is also developing a green bio convergence new industry development plan to foster alternative foods, but there are difficulties in commercialization due to the lack of technology and insufficient production facilities among domestic small and medium-sized enterprises, so it is necessary to build joint utilization facilities and equipment to resolve the difficulties faced by companies. am. In addition, small and medium-sized enterprises are having difficulty developing and commercializing plant-based meat substitutes due to a lack of technical skills, and related equipment is expensive, making it difficult to build equipment on their own. Accordingly, Jeollabuk-do is pursuing a strategy to secure the source technology for development, processing, and industrialization of plant-based substitute meat at the level of developed countries by establishing a plant-based alternative meat industrialization center. In this study, an economic feasibility analysis study was conducted when a plant-based alternative meat industrialization center is built in Jeollabuk-do. As a result of the analysis, B/C=1.32, NPV=374 million won, and IRR=4.8%, showing that there is economic feasibility in establishing an alternative meat industrialization center. In addition, as a result of analyzing the regional economic ripple effect resulting from the establishment of an industrialization center, if 38 billion won is invested in Jeollabuk-do, the nationwide production inducement effect is 74 billion won, the added value inducement effect is 29.8 billion won, and the employment inducement effect is 672 people

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.377-384
• /
• 2010

We perform a comparative study to investigate the properties of the new energetic chain extender (AzPD). A series of poly(glycidyl azide)/poly(tetramethylene oxide)-based energetic segmented polyurethane (GAP/PTMG ESPU) with different chain extender, which is 3-azidopropane-1,2-diol (AzPD), 1,4-butane diol (1,4-BD), or 1,5 pentane diol (1,5-PD), was synthesized by solution polymerization in dimethyl formamide (DMF) and their phase behaviors were investigated. The ESPUs were characterized with Fourier transform infrared-attenuated total reflection spectroscopy (ATR FT-IR), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The results of the ATR FT-IR analysis of the urethane carbonyl group region showed that the 'free' C=O fraction was higher in GAP/PTMG AzESPU (0.5) than GAP/PTMG BDESPU (0.44) and GAP/PTMG PDESPU (0.41) for 7 days samples after preparation and that it was similar in the range of 0.26~0.29 for three 60 days ESPU samples. DMA curves of the GAP/PTMG AzESPU for 7 days samples showed amorphous polymers, but GAP/PTMG BDESPU and GAP/PTMG PDESPU showed viscoelastic behaviors with rubbery plateau and the flow region. However, DMA curves of the GAP/PTMG AzESPU for 60 days samples showed viscoelastic behaviors with rubbery plateau and the flow region like GAP/PTMG PDESPU, but GAP/PTMG BDESPU did not show the flow region. From phase behaviors with ATR FT-IR, DSC and DMA analysis, GAP/PTMG AzESPU showed good phase-mixing between components. However, it represented viscoelastic behavior of TPE similar to GAP/PTMG PDESPM according to phase equilibrium progress with aging time.

• Korean Journal of Environmental Agriculture
• /
• v.32 no.4
• /
• pp.332-337
• /
• 2013

BACKGROUND: Newly reclaimed land has poor soil environment for crop growth since it is high in salt concentration but low in organic content compared with ordinary soil. It is known that whole-crop-barley can grow better in the soil of relatively high salt concentration than other crops but, the growth is poor at the concentration if higher than certain amount and it is a difficulty to secure productivity. Hence, the level of soil salt concentration suitable for the production of bulky feed in newly reclaimed land has been investigated. METHODS AND RESULTS: At Saemanguem reclaimed land, the land for the soil salt concentration electrical conductivity (EC) 0.8, 3.1, 6.5, 11.0 dS/m was selected; and chemical fertilizer $N-P_2O_5-K_2O$ (150-100-100kg/ha) was tested; and forage barley 220kg/ha were sown. The soil salt concentration during the cultivation period decreased in the order of harvest season>earing season>sowing season>wintering season, and the salt concentration in harvest season is 1.4-4.2 times higher than that of the sowing season. The higher the salt concentration, the poorer the over ground growth due to poor rooting; especially at EC 11.0 ds/m there was emergence but, it blighted after wintering. The Yield from the soil salt concentration 3.1dS/m and 6.5 dS/m was 68% and 35% from that of the soil salt concentration 0.8 dS/m (8.8 MT/ha) respectively. The proline content in early life stage was more than that of the harvest season, and it increased with salt concentration. The higher salt concentration, the more $Na_2O$ and MgO content in harvest season; but the higher the salt concentration, the less the content of N, $P_2O_5$, $K_2O$ and CaO. CONCLUSION(S): When the soil salt concentration becomes higher than 3.1 dS/m, the yield becomes poor because there is serious growth inhibition of forage barley both in root part and above aerial part that results in unbalanced absorption of nutrients. Therefore, it is recommended that the salt concentration should be lowered below 3.1 dS/m by underground drainage facilities or irrigating water for the stable production of whole-crop-barley.

• Korean journal of applied entomology
• /
• v.47 no.4
• /
• pp.385-394
• /
• 2008

Larvae of Monochamus saltuarius showed normal growth and development on conifers of Pinus koraiensis, P. densiflora, Abies holophylla, Larix leptolepsis, P. bungeana, and P. rigida, respectively, but the conifers influenced significantly the body weight and the survival rate of larvae. Though the larval body weights were in a wide spectrum among treatments, growth curves of them were very similar from each other, showing continuous increase from the early larval stage to about 3 months old. The body weight was decreased slightly after the feeding period of the early 3 months. The size of larvae and adults became the largest from P. bungeana fed larvae. The mid-sized ones were from P. koraiensis, P. densiflora and A. holophylla. Small ones came from L. leptolepsis and P. rigida. The larval growth was retarded without water supply. Overall survival rates from the early stage of a larva to a fertile adult were 53.6% from P. koraiensis; 51.8%, P. densiflora; 34.7%, A. holophylla; 17.8%, P. bungeana; 16.7%, L. leptolepsis; and 12.3%, P. rigida. Adults from larvae fed the 6 species of conifers, respectively, were grown into the reproductively potent adults, which laid viable eggs. A few of overwintered larvae did not pupate and remained still as a larva until the late October of the year. Data from the field survey, the head width emerged from P. koraiensis was larger than that of L. leptolepsis. The adult emergence hole in P. koraiensis was larger also. While, the size of the emergence hole was larger in the artificially innoculated log of P. koraiensis, which was kept for a larva to be with a minimized food competition and sufficient water supply, than that of the field.