• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.849-854
• /
• 2001

A study on performance of the sound absorbing noise barrier is presented. Noise barrier of sound absorbing type is composed of the front panel, sound absorbing material, and back panel. For allowing sound path, front panel is usually perforated. The performance of the noise barrier is governed by the opening ratio of the perforated panel, sound absorption coefficient of the sound absorbing material. In this study, the effects of the opening ratio, diameter of the hole, thickness of the sound absorbing material are investigated. It is found that the thickness of the sound absorbing material must be at least 50 mm to ensure the required minimum NRC value 0.70, and the opening ratio is greater than 0.2. It is shown that the thickness of the back panel is crucial in providing required STL (Sound Transmission Loss) value. The performance of the developed noise barrier is measured, where its sound absorbing coefficient and sound transmission loss satisfy the criteria.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• 제21권9호
• /
• pp.1627-1634
• /
• 2017

In this work, a junctionless transistor with different film thickness of amorphous InGaZnO has been fabricated and it's instability has been analyzed with different film thickness under positive and negative gate stress as well as light illumination. It was found that the threshold voltage shift and the variation of drain current have been increased with decrease of film thickness under the condition of gate stress and light illumination. The reasons for the observed results have been explained by stretched-exponential model and device simulation. Due to the reduced carrier trapping time with decrease of film thickness, electrons and holes can be activated easily. Due to the increase of vertical channel electric field reaching the back interface with decrease of film thickness, more electrons and holes can be accumulated in back interface. When one decides the film thickness for the fabrication of junctionless transistor, the more significant device instability with decrease of film thickness should be consdered.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.102-105
• /
• 2001

The spring back taking place after the coiling process of steam generator tube leads to the dimensional inaccuracy. In order to reduce the spring back, tension force was applied to the one end of the tube during forming. In this work, parametric study using FEM was performed to find the appropriate magnitude of tension force. The force that induces minimum suing back was found by simultaneously taking account of suing back amount, cross-sectional ovality, and thickness of the tube wall after deformation. In addition, stress relieving by heat treatment was also simulated as an alternative to the former method. The latter was found to be more effective under the given constraints.

• Transactions of Materials Processing
• /
• 제11권3호
• /
• pp.238-245
• /
• 2002

The spring back taking place after the coiling process of steam generator tube leads to the dimensional inaccuracy. In order to reduce the spring back, tension force was applied to the one end of the tube during forming. In this work, parametric study using FEM was performed to find the appropriate magnitude of tension force. The force that induces minimum spring back was found by simultaneously taking account if spring back amount, cross-sectional ovality, and thickness of the tube wall after deformation. In addition, stress relieving by heat treatment was also simulated as an alternative to the former method. The latter was found to be more effective under the given constraints.

• Journal of Welding and Joining
• /
• 제27권1호
• /
• pp.71-78
• /
• 2009

In the circumferential welding of pipe, welding phenomenon changes with the position of pipe. Especially in the overhead position, back bead of vertical-up position would be sunk. To investigate the size of back bead and keyhole with the change of the flow rate of pilot and shield gas at each position, bead-on plate welds were conducted on 6mm thickness SS400 with inclined-up position. When the rest of welding conditions remained constant, the width of back bead was increased as the flow rate of pilot gas was increased. And back bead tended to convex as the flow rate of shield gas was increased.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제26권9호
• /
• pp.701-706
• /
• 2013

We have focused on the conversion efficiency of CIGS thin film solar cell prepared by co-evaporation method as well as the optimization of process condition. The total thickness of back electrode was fixed at 1 ${\mu}m$ and the structural, electric and optical properties of CIGS thin film were investigated by varying the thickness of Mo:Na bottom layer from 0 to 500 nm. From the experimental results, the content of Na was appeared as 0.28 atomic percent when the thickness of Mo:Na layer was 300 nm with compactly densified plate-shape surface morphology. From the XRD measurements, (112) plane was the strongest preferential orientation together with secondary (220) and (204) planes affecting to the crystallization. The lowest roughness and resistivity were 2.67 nm and 3.9 ${\Omega}{\cdot}cm$, respectively. In addition, very high carrier density and hole mobility were recorded. From the optimization of Mo:Na layer, we have achieved the conversion efficiency of 9.59 percent.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• 제20권6호
• /
• pp.773-777
• /
• 2011

Conventional ultrasonic thickness measurement is to be considered as the assumption that the ultrasonic velocity is known. In actual applications the velocity is often not well known and access is often limited to one side. This paper aims at determining the ultrasonic velocity and thickness of plates with parallel or wedged surfaces using contact measurements made on one surface only. For wedged plates the thickness at one point and the wedge angle are determined. Equations are used for determining the ultrasonic velocity, thickness and wedge angle of the plate based on the times-of-flight measured by two contact transducers coupled to one surface. The time-of-flight of the obliquely reflected longitudinal wave echo was measured as a function of the separation between the two transducers. In addition, a simulation was made for comparing the experimental data and a FEM image. Experiments and simulations were performed on flat and wedged plates of aluminium materials; the calculated results for the unknown quantities are generally agreed with them to some degree.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1824-1826
• /
• 2000

Up to date, the dual scanning method has been adopted to decrease address-ing period in AC PDP. In this case, addressing period can be reduced, but the driving circuit cost should be increased. In this study, to increase addressing speed we have studied the relationship between addressing speed and cell structure. That is to say, we varied the thickness of dielectric layer on the front glass, the thickness of white back and the height of barrier rib on the rear glass. So, we found that the addressing time was decreased 4% with decreasing 5um thickness of dielectric layer on the front glass and 2um thickness of white back on the rear glass. Also in case of decreasing the height of barrier rib, addressing time was decreased about 4% per 10um.

• Journal of Physiology & Pathology in Korean Medicine
• /
• 제19권2호
• /
• pp.561-567
• /
• 2005

We statistically analyzed the relationship between the constitution and the thickness and stiffness of skin depending on sex and age, using 1079 clinical data registered to SCIB(Sasang constitution Information Bank), and the following results are obtained : The thickness of skin has big discrimination ability in classification of Taeeumin and Soyangin, especially in women and in ages 21 or more. The stiffness of skin also has big discrimination ability in classification of Taeeumin and Soeumin, especially in Taeumin women and Soeumin man and in ages 21-60. The differences stated above have been proved to be meaningful enough by Chi-square test.

• Physical Therapy Rehabilitation Science
• /
• 제12권1호
• /
• pp.19-25
• /
• 2023

Objective: Patients with scoliosis complain of various symptoms such as muscle imbalance, dysfunction, back pain, abnormal posture and gait abnormality. The most basic treatment for scoliosis is to observe the progress based on conservative treatment. Therefore, in this case report, the effect of cytoskeletal manual therapy (CMT), a soft tissue mobilization technique, on pain intensity, muscle thickness, and pressure pain threshold (PPT) in a patient with scoliosis was investigated. Design: A case report Methods: A 25-year-old male diagnosed with scoliosis visited the Neuromusculoskeletal Science Laboratory with chronic back pain. In the laboratory, scoliosis was confirmed through the X-ray image used for his diagnosis, and it was confirmed again through Adam's forward bending test. Pain, pressure pain threshold and muscle thickness were measured to compare the immediate effects of CMT applied in the laboratory for 40 minutes. Treatments were visited two weeks after the first visit and outcome measures were assessed after a total of two visits. Results: After receiving CMT up to the second session, the pain intensity decreased by 4 points and the screening angle decreased by 15 degrees. Muscle thickness decreased in all but 10 mm on the dominant side of the thoracic spine. All of the PPTs increased, and the greatest increase was 3.1 lb on the dominant side of the thoracic spine. Conclusions: CMT showed positive improvement in pain during trunk flexion, spinal curvature, muscle imbalance, and pressure pain, which is considered as an ancillary treatment option for scoliosis management.