본 논문에서는 전력증폭기의 효율을 증가시키기 위해서 모드변환 가능한 단권변압기를 제안한다. 모드변환 가능한 단권변압기를 통해 전력증폭기의 저 전력 모드 동작 시 효율을 개선할 수 있다. 이 논문에서는 0.18-${\mu}m$ CMOS 표준 공정을 이용하여 듀얼모드 단권변압기를 이용한 CMOS 전력증폭기를 설계하였다. 고 전력 모드와 저 전력 모드에서 단권변압기의 1차 권선의 권선수를 조절하여 전력증폭기의 동작을 최적화하였다. EM 시뮬레이션 및 전체 회로 시뮬레이션 결과 제안된 멀티모드 CMOS 전력증폭기의 출력전력이 24dBm일 때 전력부가효율(PAE)이 10.4%에서 멀티모드 동작으로 26.1% 로 상승하여 전력증폭기의 성능 개선되었다.
본 논문에서는 mixed driving 방식을 이용하고 이미지 개선을 위해 $\gamma$-correction을 수행하는 QVGA급 TFT-LCD driver IC의 Source Driver를 설계한다. 240 RGB ${\times}$ 320 dots resolution을 가진 source driver는 720개의 채널을 통해 TFT-LCD 패널을 구동하고 18-bit의 RGB 데이터를 사용하여 26만 color를 수행한다. Mixed driving 방식은 종전의 좋은 구동력을 가진 channel amp. driving 방식에 저면적이 가능한 gray amp. driving 방식을 혼합한 방식으로서, 영상이 동일 색상을 가지는 worst case를 감지하여 구동력을 높여주는 방식을 사용함으로써 적절한 구동력과 저면적을 구현하는 설계방식이다. 본 Source Driver는 $0.35{\mu}m$ Magnachip embedded DRAM 공정을 사용하여 설계하였으며 Hspice를 사용하여 시뮬레이션을 하였다. 실험결과, 기존의 gayscale driving 방식에서는 hsync time을 만족시키지 못하는데 비해 $17{\mu}s$의 channel 구동시간으로 충분한 timing margin을 가지고 액정 channel 을 구동할 수 있으면서, 구동 앰프 78개와 제어회로를 갖는 저면적으로 설계되었다.
본 논문에서는 낮은 전압 이득 특성을 갖는 증폭기를 이용한 12비트 10MS/s 파이프라인 ADC를 제안한다. 증폭기의 낮은 전압 이득 특성에 의한 MDAC의 잔류 전압 이득 오차를 보상하기 위해 기준 전압 스케일링 기법을 적용한 파이프라인 ADC 구조를 제안하였다. 증폭기 오프셋에 의한 제안하는 ADC의 성능 저하를 개선하기 위해 첫 단 MDAC에 오프셋 조정이 가능한 증폭기를 사용하였으며, 낮은 증폭기 전압 이득으로 인해 발생하는 메모리 효과를 최소화하기 위해 추가적인 리셋 스위치를 MDAC에 적용하였다. 한편, 45dB 수준의 낮은 전압 이득을 갖는 증폭기를 기반으로 구성된 시제품 ADC는 $0.35{\mu}m$ CMOS 공정으로 제작되었으며, 측정된 최대 DNL 및 INL은 각각 0.7LSB 및 3.1LSB 수준을 보인다. 또한 2.4V의 전원 전압과 10MS/s의 동작 속도에서 최대 SNDR 및 SFDR이 각각 62dB와 72dB이며, 19mW의 전력을 소모한다.
Mohadeskasaei, Seyed Alireza;An, Jianwei;Chen, Yueyun;Li, Zhi;Abdullahi, Sani Umar;Sun, Tie
ETRI Journal
/
제39권1호
/
pp.51-61
/
2017
This paper demonstrates a systematic approach for the design of broadband, high efficiency, high power, Class-AB RF amplifiers with high gain flatness. It is usually difficult to simultaneously achieve a high gain flatness and high efficiency in a broadband RF power amplifier, especially in a high power design. As a result, the use of a computer-aided simulation is most often the best way to achieve these goals; however, an appropriate initial value and a systematic approach are necessary for the simulation results to rapidly converge. These objectives can be accomplished with a minimum of trial and error through the following techniques. First, signal gain variations are reduced over a wide bandwidth using a proper pre-matching network. Then, the source and load impedances are satisfactorily obtained from small-signal and load-pull simulations, respectively. Finally, two high-order Chebyshev low-pass filters are employed to provide optimum input and output impedance matching networks over a bandwidth of 100 MHz-500 MHz. By using an EM simulation for the substrate, the simulation results were observed to be in close agreement with the measured results.
본 논문에서는 전력 증폭기를 효과적으로 모델링하기 위한 E-TDLNN(Expanded-Tapped Delay Line Neural Network) 방식을 제안하였다. 이 방식은 전력 증폭기의 메모리 효과를 효과적으로 제시한 TDLNN 방식에 외부 변화 인자인 게이트 바이어스를 불변(invariant) 입력으로 추가한 후 측정된 전력 증폭기의 출력 스펙트럼을 목표치로 신경망을 통해 학습시킴으로써 전력 증폭기를 모델링하는 방식이다. 제안한 방식의 타당성을 증명하기 위해 주 증폭기의 게이트 바이어스를 $3.4{\sim}3.6V$ 범위에서 0.01 V 스텝으로 변화시키며 측정한 여러 데이터 중 3.45 V와 3.50 V에 대해 학습시킨 후, 게이트 바이어스가 3.40 V, 3.48 V, 3.53 V, 3.60 V인 경우에 대하여 출력을 예측한 결과 실제 출력과 거의 동일한 신호를 예측할 수 있었다.
Understanding of the basic characteristics of an astronomical instrument is a prerequisite to obtaining reliable data from the instrument. We have analyzed more than 1,000 calibration images from the Fairchild 486 CCD (hereafter the Maidanak 4k CCD system) attached to the AZT-22 1.5m telescope at Maidanak Astronomical Observatory in Uzbekistan. The Maidanak 4k CCD system supports three readout modes through 1, 2, or 4 amplifiers. In most cases observers use 4-amplifier readout mode to save time. We have tested the stability and seasonal variation of zero levels and confirm that two quadrants of the images (Amp 1 & 2) show no appreciable seasonal variation. but the other two quadrants (Amp 3 & Amp 4) show an evident seasonal variation in the bias level. The Cryo Tiger, the cooling system used at the Maidanak 4k CCD system, maintains the CCD temperature at -108'E, and effectively suppresses the dark electrons. The mean value versus the variance plot of the flat images does not show the expected relation for an ideal Poisson noise distribution and this is attributed to the large variation in quantum efficiency between different pixels. In addition, we confirm that there is no appreciable difference in gain between readout amplifiers, but there is a large variation in quantum efficiency across CCD chip especially in U. Due to the finite length of shutter opening and closing time, the effective exposure time varies across the science images. We introduce two parameters to quantify the effect of this uneven illumination and present a method to remove these effects. We also present a method to remove the interference patterns appearing in the images obtained with longer wavelength filters and investigate the spatial variation of the point spread function.
본 논문에서는 CMOS 공정을 사용하여 기가비트 이더넷 응용을 위한 전치증폭기 회로를 구현하였다 대역폭 확장 및 노이즈 성능개선을 위해, regulated cascade 설계기법을 사용하였고 이로써, 광다이오드 및 TIA 입력단의 큰 기생 캐패시턴스를 대역폭 결정으로부터 효과적으로 차단하였다. 0.6um CMOS공정을 사용하여 구현한 1.25Gb/s 전치증폭기의 칩 측정 결과 58dBohm의 트랜스 임피던스 이득, 0.5pF 기생 광다이오드 캐패시턴스에 대해 950MHz의 대역폭과 6.3pA/sqrt(Hz)의 평균 노이즈 전류 스펙트럼 밀도, 5V 단일 전원전압으로부터 85mW의 전력소모를 보였다. 또한, 0.18um CMOS 공정을 사용하여 설계한 10Gb/s 전치증폭기는 RGC 기법과 인덕티브 피킹기술을 동시에 사용함으로써, 59.4dBohm의 트랜스 임피던스 이득, 0.25pF 기생 캐패시턴스에 대해 8GHz의 대역폭, 20pA/sqrt(Hz)의 노이즈 전류 스펙트럼 밀도, 1.8V 단일전압에 대해 14mW의 전력소모를 보였다.
Andre, Marc-Olivier;Kinion, Darin;Clarke, John;Muck, Michael
한국초전도학회:학술대회논문집
/
한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
/
pp.2-6
/
2000
We have developed an extremely sensitive radio frequency amplifier based on the dc superconducting quantum interference device (dc SQUID). Unlike a conventional semiconductor amplifier, a SQUID can be cooled to ultra-low temperatures (100 mK or less) and thus potentially achieve a much lower noise temperature. In a conventional SQUID amplifier, where the integrated input coil is operated as a lumped element, parasitic capacitance between the coil and the SQUID washer limits the frequency up to which a substantial gain can be achieved to a few hundred MHz. This problem can be circumvented by operating the input coil of the SQUID as a microstrip resonator: instead of connecting the input signal open. Such amplifiers have gains of 15 dB or more at frequencies up to 3 GHz. If required, the resonant frequency of the microstrip can be tuned by means of a varactor diode connected across the otherwise open end of the resonator. The noise temperature of microstrip SQUID amplifiers was measured to be between $0.5\;K\;{\pm}\;0.3\;K$ at a frequency of 80 MHz and $1.5\;K\;{\pm}\;1.2\;K$ at 1.7 GHz, when the SQUID was cooled to 4.2 K. An even lower noise temperature can be achieved by cooling the SQUID to about 0.4 K. In this case, a noise temperature of $100\;mK\;{\pm}\;20\;mK$ was achieved at 90 MHz, and of about $120\;{\pm}\;100\;mK$ at 440 MHz.
Muck, Michael;Ande, Marc-Olivier;Kinion, Darin;Clarke, John
Progress in Superconductivity
/
제2권1호
/
pp.1-5
/
2000
We have developed an extremely sensitive radio frequency amplifier based on the dc superconducting quantum interference device (dc SQUID). Unlike a conventional semiconductor amplifier, a SQUID can be cooled to ultra-low temperatures (100 mK or less) and thus potentially achieve a much lower noise temperature. In a conventional SQUID amplifier, where the integrated input coil is operated as a lumped element, parasitic capacitance between the coil and the SQUID washer limits the frequency up to which a substantial gain can be achieved to a few hundred MHz. This problem can be circumvented. by operating the input coil of the SQUID as a microstrip resonator: instead of connecting the input signal between the two ends of the coil, it is connected between the SQUID washer and one end of the coil; the other end is left open. Such amplifiers have gains of 15 dB or more at frequencies up to 3 GHz. If required, the resonant frequency of the microstrip can be tuned by means of a varactor diode connected across the otherwise open end of the resonator. The noise temperature of microstrip SQUID amplifiers was measured to be between 0.5 K $\pm$ 0.3 K at a frequency of 80 MHz and 1.5 K $\pm$: 1.2 K at 1.7 GHz, when the SQUID was cooled to 4.2 K. An even lower noise temperature can be achieved by cooling the SQUID to about 0.4 K. In this case, a noise temperature of 100 mK $\pm$ 20 mK was achieved at 90 MHz, and of about 120 $\pm$ 100 mK at 440 MHz.
본 논문은 GaN HEMT (Gallium Nitride High Electron Mobility Transistor)를 이용하여 Class-E 스위칭 모드를 적용한 S-대역 레이더용 고효율 스위칭 도허티 전력증폭기를 설계 및 제작하였다. 제안된 도허티 전력증폭기는 캐리어 증폭기와 피킹 증폭기가 고효율 특성을 갖는 Class-E 스위칭 모드로 구성되었다. 측정을 위한 입력 RF 신호는 $100\;{\mu}s$의 펄스폭과 1 kHz의 PRF (Pulse Repetition Frequency)인 duty 10%인 펄스 신호를 사용하였다. 2.85 GHz의 주파수 대역에서 스위칭 도허티 전력증폭기 측정결과 포화전력에서 6 dB 떨어진 지점의 전력부가 효율 (power-added efficiency, PAE) 및 드레인 효율 (drain efficiency)은 각각 64%와 80.6%로 측정되었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.