• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.207-207
• /
• 2011

Amorphous transparent oxide semiconductors (a-TOS) have been widely studied for many optoelectronic devices such as AM-OLED (active-matrix organic light emitting diodes). Recently, Nomura et al. demonstrated high performance amorphous IGZO (In-Ga-Zn-O) TFTs.1 Despite the amorphous structure, due to the conduction band minimum (CBM) that made of spherically extended s-orbitals of the constituent metals, an a-IGZO TFT shows high mobility.2,3 But IGZO films contain high cost rare metals. Therefore, we need to investigate the alternatives. Because Aluminum has a high bond enthalpy with oxygen atom and Alumina has a high lattice energy, we try to replace Gallium with Aluminum that is high reserve low cost material. In this study, we focused on the electrical properties of IZO:Al thin films as a channel layer of TFTs. IZO:Al were deposited on unheated non-alkali glass substrates (5 cm ${\times}$ 5 cm) by magnetron co-sputtering system with two cathodes equipped with IZO target and Al target, respectively. The sintered ceramic IZO disc (3 inch ${\phi}$, 5 mm t) and metal Al target (3 inch ${\phi}$, 5 mm t) are used for deposition. The O2 gas was used as the reactive gas to control carrier concentration and mobility. Deposition was carried out under various sputtering conditions to investigate the effect of sputtering process on the characteristics of IZO:Al thin films. Correlation between sputtering factors and electronic properties of the film will be discussed in detail.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.137-137
• /
• 2009

Indium Gallium Zinc Oxide (IGZO) thin films for TFT channel were prepared by using a Facing Target Sputtering (FTS) system. To investigate the effect of oxygen on the optical and the electrical properties of amorphous InGaZnO(a-IGZO), we prepared thin films by FTS system in various oxygen atmospheres at room temperature. As-deposited IZTO thin films were investigated by using a UV/VIS spectrometer, an X-ray diffractometer, a Hall Effect measurement system, and an atomic force microscope. The quantitative analysis of the films was carried out by using the energy dispersive X-ray (EDX) technique for the as-deposited film.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.4
• /
• pp.721-726
• /
• 2017

We fabricated stretchable thin-film transistors(TFTs) on a polydimethylsiloxane substrate with patterned polyimide island structures by using an amorphous InGaZnO semiconductor and parylene gate insulator. The TFTs exhibited a field- effect mobility of $5cm^2V^{-1}s^{-1}$ and a current on/off ratio of $10^5$ at a relatively low operating voltage. Furthermore, the fabricated transistors showed no noticeable changes in their electrical performance for large strains of up to 50 %.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.4
• /
• pp.235-237
• /
• 2016

Oxide/metal/oxide (OMO) thin films were fabricated using amorphous indium-gallium-zinc-oxide (a-IGZO) and an Ag metal layer on a glass substrate at room temperature. The optical and electrical properties of the a-IGZO/Ag/a-IGZO samples changed systemically depending on the thickness of the Ag layer. The transmittance in the visible range tends to decrease as the Ag thickness increases while the resistivity, carrier concentration, and Hall mobility tend to improve. The a-IGZO/Ag (13 nm)/a-IGZO thin film with the optimum Ag thickness showed an average transmittance (T_av) of 71.7%, resistivity of 6.63 × 10⁻⁵ Ω·cm and Hall mobility of 15.22 cm²V⁻¹s⁻¹.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.338.1-338.1
• /
• 2014

비정질 산화물 반도체(Amorphous Oxide Smeiconcuctor)를 이용하여 투명 박막 트랜지스터의 채널층으로 많은 연구가 진행되고 있다. 투명 박막 트랜지스터의 채널층으로 사용되고 있는 IGZO박막은 비정질임에도 불구하고 높은 이동도와 넓은 밴드갭을 갖고 있는 것으로 알려져 있다. 본 연구는 RF magnetron sputtering법으로 유리기판 위에 IGZO박막을 증착시켰으며 소결된 타겟으로는 In:Ga:ZnO를 각각 1:1:2mol%의 조성비로 혼합하여 이용하였으며, $30{\times}30mm$의 XG Glass 유리기판에 sputtering 방식으로 증착하였다. 박막 증착 조건은 초기압력 $3.0{\times}10^{-6}Torr$, 증착 압력 20mTorr, 반응가스 Ar 25sccm, 공정 변수로는 RF Power 25W, 50W, 75W, 100W 각각 변화를 주어 실험을 진행 하였으며, 증착온도는 실온으로 고정 하였다. 분석 결과로 RF Power 25W 일 때 XRD 분석결과 Bragg's 법칙을 만족하는 피크가 나타나지 않는 비정질 구조임을 확인하였으며, AFM 분석결과 0.5 mm 이하의 Roughness를 가졌다. UV-Visible-NIR 측정 결과 가시광선 영역에서 87%이상의 투과도를 나타냈으며, Hall 측정 결과 Carrier concentration $3.31{\times}10^{19}$, Mobility $10.9cm^2/V.s$, Resistivity $1.8{\times}10^{-2}$, 투명 박막 트랜지스터의 채널층으로 사용 가능함을 확인 할 수 있었다.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.2
• /
• pp.72-76
• /
• 2020

The author demonstrated organic ferroelectric thin-film transistors with ferroelectric materials of P(VDF-TrFE) and an amorphous oxide semiconducting In-Ga-Zn-O channel on the silicon substrates. The organic ferroelectric layers were deposited on an oxide semiconductor layer by Langmuir-Blodgett method and then annealed at 128℃ for 30min. The carrier mobility and current on/off ratio of the memory transistors showed 9 ㎠V^-1s^-1 and 6 orders of magnitude, respectively. We can conclude from the obtained results that proposed memory transistors were quite suitable to realize flexible and werable electronic applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.169-169
• /
• 2010

As display industry requires various applications for future display technology, which can guarantees high level of flexibility and transparency on display panel, oxide semiconductor materials are regarded as one of the best candidates. $InGaZnO_4$(IGZO) has gathered much attention as a post-transition metal oxide used in active layer in thin-film transistor. Due to its high mobility fabricated at low temperature fabrication process, which is proper for application to display backplanes and use in flexible and/or transparent electronics. Electrical performance of amorphous oxide semiconductors depends on the resistance of the interface between source/drain metal contact and active layer. It is also affected by sheet resistance on IGZO thin film. Controlling contact/sheet resistance has been a hot issue for improving electrical properties of AOS(Amorphous oxide semiconductor). To overcome this problem, post-annealing has been introduced. In other words, through post-annealing process, saturation mobility, on/off ratio, drain current of the device all increase. In this research, we studied on the relation between device's resistance and post-annealing temperature. So far as many post-annealing effects have been reported, this research especially analyzed the change of electrical properties by increasing post-annealing temperature. We fabricated 6 main samples. After a-IGZO deposition, Samples were post-annealed in 5 different temperatures; as-deposited, $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$ and $500^{\circ}C$. Metal deposition was done on these samples by using Mo through E-beam evaporation. For analysis, three analysis methods were used; IV-characteristics by probe station, surface roughness by AFM, metal oxidation by FE-SEM. Experimental results say that contact resistance increased because of the metal oxidation on metal contact and rough surface of a-IGZO layer. we can suggest some of the possible solutions to overcome resistance effect for the improvement of TFT electrical performances.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.54.1-54.1
• /
• 2010

산화물 기반의 TFT는 유리, 금속, 플라스틱 등 기판 종류에 상관없이 균일한 제작이 가능하며, 상온 및 저온에서 대면적으로 제작이 가능하고, 저렴한 비용으로 제작 가능하다는 장점 때문에 최근 많은 연구가 이루어지고 있다. 현재 TFT 물질로 많이 연구되고 있는 산화물은 ZnO (3.4 eV)나 InOx (3.6 eV), GaOx (4.9 eV), SnOx(3.7 eV)등의 물질과 각각의 조합으로 구성된 재료들이 주로 사용되고 있으며, 가장 많은 연구가 이루어진 ZnO 기반의 TFT는 mobility와 switching 속도에서 우수한 특성을 보이나, 트렌지스터의 안정성이 떨어지는 것으로 보고 되고 있다. 그러나 IGZO 물질의 경우 결정학적으로 비정질이며 상온 및 저온에서 대면적으로 제작이 가능하고, 높은 전자 이동도의 특성을 가지고 있는 장점 때문에 최근 차세대 산화물 트렌지스터로 각광받고 있다. IGZO TFT 소자의 경우 Ag, Au, In, Pt, Ti, ITO 등 다양한 전극 물질이 사용되고 있는데, 이들 중 active channel과 ohmic contact을 이루는 Al, Ti, Ag의 적용을 통해 향상된 성능을 얻을 수 있다. 하지만 이들 전극 재료는 TFT 소자 제작시 필수적인 열처리 공정에 노출되면서 active channel 과 전극 사이 계면에 문제점을 야기할 수 있다. 특히, Ti의 경우 산화가 잘되기 때문에 전극계면에 TiO2를 형성하여 contact resistance의 큰 영향을 미치는 것으로 보고 되고 있다. 본 연구에서는 ohmic 전극재료인 Ti 또는 Ti/Au를 적용하여 TFT 소자 제작 및 특성에 대한 평가를 진행했으며, 열처리에 따른 전극과 IGZO 계면 사이의 미세구조와 전기적인 특성간의 상관관계를 연구하였다. 이를 통해, 소자 제작 공정을 최적화하고 신뢰성 있는 소자 특성을 얻을 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.5-5
• /
• 2009

Thin-film-transistors (TFTs) that can be prepared at low temperatures have attracted much attention because of the great potential for transparent and flexible electronics. One of the mainstreams in this field is the use of organic semiconductors such as pentacene. But device performance of the organic TFTs is still limited due to low field-effect mobility and rapid degradation after exposing to air. Alternative approach is the use of amorphous oxide semiconductors as a channel. Amorphous oxide semiconductors (AOSs) based TFTs showed the fast technological development, because AOS films can be fabricated at room temperature and exhibit the possibility in application like flexible display, electronic paper, and larges solar cells. Among the various AOSs, a-IGZO has lots of advantages because it has high channel mobility, uniform surface roughness and good transparency. [1] The high mobility is attributed to the overlap of spherical s-orbital of the heavy post-transition metal cations. This study demonstrated the effect of the variation in channel thickness from 30nm to 200nm on the TFT device performance. When the thickness was increased, turn-on voltage and subthreshold swing was decreased. The a-IGZO channels and source/drain metals were deposited with shadow mask. The a-IGZO channel layer was deposited on $SiO_2$/p-Si substrates by RF magnetron sputtering, where RF power is 150W. And working pressure is 3m Torr, at $O_2/Ar$ (2/28 sccm) atmosphere. The electrodes were formed with electron-beam evaporated Ti (30 nm) and Au (70 nm) bilayer. Finally, Al (150nm) as a gate metal was thermal-evaporated. TFT devices were heat-treated in a furnace at 250 $^{\circ}C$ and nitrogen atmosphere for 1hour. The electrical properties of the TFTs were measured using a probe-station. The TFT with channel thickness of 150nm exhibits a good subthreshold swing (SS) of 0.72 V/decade and on-off ratio of $1{\times}10^8$. The field effect mobility and threshold voltage were evaluated as 7.2 and 8 V, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.163-163
• /
• 2015

The effect of nematic liquid crystal(5CB-4-Cyano-4'-pentylbiphenyl) on the amorphous indium gallium zinc oxide thin film transistors(a-IGZO TFTs) was investigated. Through dropping the 5CB on the a-IGZO TFT's channel layer which is deposited by RF-magnetron sputtering, properties of a-IGZO TFTs was dramatically improved. When drain bias was induced, 5CB molecules were oriented by Freedericksz transition generating positive charges to one side of dipoles. From increment of the capacitance by orientation of liquid crystals, the drain current was increased, and we analyzed these phenomena mathematically by using MOSFET model. Transfer characteristic showed improvement such as decreasing of subthreshold slope(SS) value 0.4 to 0.2 and 0.45 to 0.25 at linear region and saturation region, respectively. Furthermore, in positive bias system(PBS), prevention effect for electron trapping by 5CB liquid crystal dipoles was observed, which showing decrease of threshold voltage shift [(${\delta}V$]_TH) when induced +20V for 1~1000sec at the gate electrode.