• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.4
• /
• pp.312-317
• /
• 2004

High dose ($3{\times}10^{16}cm^{-2}$) implantation of Fe or Ni ions into bulk, single-crystal ZnO substrates was carried out at substrate temperature of ${\sim}350^{\circ}C$ to avoid amorphization of the implanted region. The samples were subsequently annealed at $700^{\circ}C$ to repair some of the residual implant damage. X-Ray Diffraction did not show any evidence of secondary phase formation in the ZnO. The Ni implanted samples remained paramagnetic but the Fe-implanted ZnO showed evidence of ferromagnetism with an approximate Curie temperature of ${\sim}$240K. Preliminary X-Ray Photoelectron Spectroscopy measurements showed the Fe to be ill the 2+ oxidation state. The earrler density in the implanted region still appears to be too low to support carrier-meditated origin of the ferromagnetism and formation of bound magnetic polarons may be one potential explanation for the observed magnetic properties, No evidence of the Anomalous Hall Effect could be found in the Fe-implanted ZnO, but its transport properties were dominated by the conventional or ordinary Hall effect.

• Korean Journal of Materials Research
• /
• v.24 no.11
• /
• pp.632-638
• /
• 2014

We investigated the effects of DMAB (Borane dimethylamine complex, C2H10BN) in electroless Ni-B film with addition of DMAB as reducing agent for electroless Ni plating. The electroless Ni-B films were formed by electroless plating of near neutral pH (pH 6.5 and pH 7) at $50^{\circ}C$. The electroless plated Ni-B films were coated on screen printed Ag pattern/PET (polyethylene terephthalate). According to the increase of DMAB (from 0 to 1 mole), the deposition rate and the grain size of electroless Ni-B film increased and the boron (B) content also increased. In crystallinity of electroless Ni-B films, an amorphization reaction was enhanced in the formation of Ni-B film with an increasing content of DMAB; the Ni-B film with < 1 B at.% had a weak fcc structure with a nano crystalline size, and the Ni-B films with > 5 B at.% had an amorphous structure. In addition, the Ni-B film was selectively grown on the printed Ag paste layer without damage to the PET surface. From this result, we concluded that formation of electroless Ni-B film is possible by a neutral process (~green process) at a low temperature of $50^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.21 no.2
• /
• pp.106-110
• /
• 2011

A high thermal conductive AlN composite coating is attractive in thermal management applications. In this study, AlN-YAG composite coatings were manufactured by atmospheric plasma spraying from two different powders: spray-dried and plasma-treated. The mixture of both AlN and YAG was first mechanically alloyed and then spray-dried to obtain an agglomerated powder. The spray-dried powder was primarily spherical in shape and composed of an agglomerate of primary particles. The decomposition of AlN was pronounced at elevated temperatures due to the porous nature of the spray-dried powder, and was completely eliminated in nitrogen environment. A highly spherical, dense AlN-YAG composite powder was synthesized by plasma alloying and spheroidization (PAS) in an inert gas environment. The AlN-YAG coatings consisted of irregular-shaped, crystalline AlN particles embedded in amorphous YAG phase, indicating solid deposition of AlN and liquid deposition of YAG. The PAS-processed powder produced a lower-porosity and higher-hardness AlN-YAG coating due to a greater degree of melting in the plasma jet, compared to that of the spray-dried powder. The amorphization of the YAG matrix was evidence of melting degree of feedstock powder in flight because a fully molten YAG droplet formed an amorphous phase during splat quenching.

• Journal of Powder Materials
• /
• v.12 no.6 s.53
• /
• pp.433-440
• /
• 2005

The hydrogen sorption speed of $Zr_{57}V_{36}Fe_7$ nanocrystalline and amorphous alloys was evaluated at room temperature. Nanocrystalline alloys of $Zr_{57}V_{36}Fe_7$ were prepared by planetary ball milling. The hydrogen sorption speed of nanocrystalline alloys was higher than that of the amorphous alloy. The enhanced sorption speed of nanocrystalline alloys was explained in terms of surface oxygen stability which has been known to retard the activation of amorphous alloys. The retardation can be reduced by formation of nanocrystals, which results in the observed increase in sorption properties.

• Korean Journal of Materials Research
• /
• v.10 no.1
• /
• pp.29-33
• /
• 2000

The amorphous tungsten nitrides, WNx, film could be fabricated by reactive sputtering process. The nitrogen concentration for the amorphization ranges from 10 at% to 40at%. The amorphous $W_{67}N_{33}$ film was crystallized into low resistivity $\alpha$-tungsten phase with equiaxed grains and excess nitrogen after the rapid thermal annealing for 1min at 1273K, which was similar to the resistivity of the sputtered pure tungsten film. The excess nitrogen was depleted from $\alpha$-tungsten crystals and then segregated at $\alpha$-tungsten/poly-Si interface. The segregated nitrogen has favored the formation of the homogeneous diffusion barrier layer comprised of silicon nitride, $Si_3N_4$, nano-crystals, which undertaken the inhibition of the high resistivity tungsten silicide reaction.

• Korean Journal of Materials Research
• /
• v.9 no.8
• /
• pp.787-791
• /
• 1999

TiB$_2$powders were prepared by mechanical alloying, and the effect of Zr and Ta substitution for Ti was investigated. It was possible to produce titanium diboride phase by mechanical alloying titanium and boron elemental powders for 280 hours. The amorphization reaction, a common process which occurs during mechanical alloying, has not been found. When zirconium of which atomic radius was larger than that of titanium was substituted for Ti, the alloying time was greatly reduced. On the contrary, substitution of tantalum for titanium prolonged the alloying time because of the less negative heat of formation of tantalum diboride than that of titanium diboride.

• Korean Journal of Materials Research
• /
• v.8 no.12
• /
• pp.1133-1137
• /
• 1998

By the mechanical alloying method Ni-W(WC) composite materials were prepared to improve the resistance for creep and sintering of Ni-anode at the operating temperature of$ 650^{\circ}C$. Amorphization was observed from the XRD analysis of mechanically alloyed powder caused by the destruction of ordered crystals. Sintering was performed at $1280^{\circ}C$ for 10 hours in $H_2$ atmosphere. From the result of dot-mapping and TEM analysis the second phase was not observed at Ni-W interface while W particles of less 0.lam were distributed finely and uniformly in Ni matrix. This finely and uniformly distributed W in Ni matrix is expected to enhance the mechanical properties of Ni-anode through the dispersion and solid solution hardening mechanisms.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.493-496
• /
• 2009

Phase stabilized leucite, which has high coefficient of thermal expansion, was synthesized, and its thermal expansion behavior was investigated. The homogeneous leucite phase was synthesized by solid state reaction from the mixture of $K_2CO_3-Al_2O_3-SiO_2$. and its stabilization from tetragonal to cubic phase was attempted by adding $Cs_2CO_3$ into starting materials. And fine powder with an average particle size of a few hundreds ${\mu}m$ were fabricated by planetary milling. During milling, amorphization of leucite was observed and recrystallized after heat treatment. The thermal expansion behavior of tetragonal and cubic leucite has measured and discussed. The average coefficient of thermal expansion of tetragonal and cubic phase leucite from room temperature to $750^{\circ}C$ was $21.4{\times}10^{-6}/^{\circ}C$ and $14.5{\times}10^{-6}/^{\circ}C$, respectively.

• Carbon letters
• /
• v.27
• /
• pp.18-25
• /
• 2018

In this study, graphene oxide(GO) was used as drug carriers to amorphize poorly watersoluble drugs via a co-spray drying process. Two poorly water-soluble drugs, fenofibrate and ibuprofen, were investigated. It was found that the drug molecules could be in the graphene nanosheets in amorphous or nano crystalline forms and thus have a significantly enhanced dissolution rate compared with the counterpart crystalline form. In addition, the dissolution of the amorphous drug enwrapped with the graphene oxide was higher than that of the amorphous drug in activated carbon (AC) even though the AC possessed a larger specific surface area than that of the graphene oxide. The amorphous formulations also remained stable under accelerated storage conditions ($40^{\circ}C$ and 75% relative humidity) for a study period of 14 months. Therefore, graphene oxide could be a potential drug carrier and amorphization agent for poorly water-soluble drugs to enhance their bioavailability.

• Journal of Powder Materials
• /
• v.17 no.1
• /
• pp.7-12
• /
• 2010

In this work, effect of various process-control agents (PCAs) on the mechanical alloying of amorphous alloy of $Al_{85}Y_8Ni_5Co_2$ has been investigated. The dependence of the particle shape, size and crystallization behavior of the amorphous alloy powders on the type of PCAs and their concentrations was investigated by using X-ray diffraction, field-emission scanning electron microscopy and differential scanning calorimetry. It was found that the additive of toluene could affect positively the amorphization and thermally induced crystallization processes, as well as the size refinement, morphology and particle-size distribution of as-milled powders in comparison with alloy obtained without PCA.