• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.530-543
• /
• 2015

Air-cooling method is adopted on the basis of the requirements for the thermal stability and convenient field use of an electrical source transmitter. The power losses of the transmitter are determined after calculating the losses of the alternating current (AC)-direct current (DC) power supply, the constant-current circuit, and the output circuit. According to the analysis of the characteristics of a heat sink with striped fins and a fan, the engineering calculation expression of the Nusselt number and the design process for air-cooled dissipation are proposed. Experimental results verify that the error between calculated and measured values of the transmitter losses is 12.2%, which meets the error design requirements of less than 25%. Steady-state average temperature rise of the heat sink of the AC-DC power supply is $22^{\circ}C$, which meets the design requirements of a temperature rise between $20^{\circ}C$ and $40^{\circ}C$. The transmitter has favorable thermal stability with 40 kW output power.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.309-318
• /
• 2015

This study proposes a dual-output single-stage bridgeless single-ended primary-inductor converter (DOSSBS) that can completely remove the front-end full-bridge alternating current-direct current rectifier to accomplish power factor correction for universal line input. Without the need for bridge diodes, the proposed converter has the advantages of low component count and simple structure, and can thus significantly reduce power loss. DOSSBS has two uncommon output ports to provide different voltage levels to loads, instead of using two separate power factor correctors or multi-stage configurations in a single stage. Therefore, this proposed converter is cost-effective and compact. A magnetically coupled inductor is introduced in DOSSBS to replace two separate inductors to decrease volume and cost. Energy stored in the leakage inductance of the coupled inductor can be completely recycled. In each line cycle, the two active switches in DOSSBS are operated in either high-frequency pulse-width modulation pattern or low-frequency rectifying mode for switching loss reduction. A prototype for dealing with an $85-265V_{rms}$ universal line is designed, analyzed, and built. Practical measurements demonstrate the feasibility and functionality of the proposed converter.

• Journal of Power Electronics
• /
• v.13 no.6
• /
• pp.975-984
• /
• 2013

This paper proposes a robust optimal nonlinear control with an observer to reject the offset errors of position tracking for surface mounted permanent magnet synchronous motors. We provide the control method to reject offset errors and load torque for designing field oriented control (FOC) based the alternating current (AC) frame. The proposed method consists of a torque generator, a commutation scheme, an electrical controller, and a load torque observer. The mechanical controller is designed to compensate for load torque and the offset error and generate the desired torque. The commutation scheme is proposed to create the desired currents for the desired torque. The electrical controller is developed to guarantee the desired currents. The observer is designed to estimate both the velocity and the load torque. In order to obtain the robustness to parameter uncertainties and a gain tuning guide, the linear quadratic regulator method is applied to the proposed method. The closed-loop stability is proven. A detailed process for the FOC design and an analysis of the control methods based on the AC frame are presented. The performance of the proposed method was validated via experiments. The proposed method obtains the FOC based on the AC frame. Furthermore, the position tracking performance of the proposed method is superior to that of the conventional method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.529-530
• /
• 2007

The paper considers the relation between on-line monitoring and diagnostics on the one hand and high-voltage (HV) withstand and partial discharge (PD) on-site testing on the other. HV testing supplies the basic data (fingerprints) for diagnostics. In case of warnings by on-line diagnostic systems, off-line withstand and PD testing delivers the best possible information about defects and enables the classification of the risk. Because alternating voltage (AC) is the most important test voltage, the AC generation on site is considered. Frequency tuned resonant (ACRF) test systems are best adapted to on-site conditions. They can be simply combined with PD measuring equipment. The available ACRF test systems and their application to electric power equipment -from cable systems to power transformers - is described.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.61-66
• /
• 2002

A method for designing antireflection (AR) and antistatic (AS) coating layer by the use of conducting polymer as an electrically conductive transparent layer is proposed. The conducting AR coating is composed of four-layer with alternating high and low refractive index layer: silicon dioxide (n=1.44) and titanium dioxide (n=2.02) prepared at low temperature by sol-gel method are used as the low and high refractive index layer, respectively. The poly(3,4-ethylenedioxythiophene) which has the surface resistivity of 10$^4$Ω/$\square$ is used as a conductive layer. Optical constant of each ARAS coating layers such as refractive index and optical thickness were measured by 7he spectroscopic ellipsometer and from the measured optical constants the spectral properties such as reflectance and transmittance were simulated in the risible region. The reflectance of ARAS films on glass substrate was below 1 %R and the transmittance was higher than 95 % in the visible wavelength (400-700 nm). The measured AR spectral properties was very similar to its simulated results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.144-150
• /
• 2003

The chalcogenide glasses of thin films have the superior property of photoinduced anisotrophy(PA). In this study, we observed the linear dichroism using the irradiation with Polarized He-Ne laser light in the Ag/As$_{40}$ Ge$_{10}$Se$_{15}$ S$_{35}$ multi-layer. Multilayer structures were formed by alternating metal(Ag) and chalcogenide(As$_{40}$ Ge$_{10}$Se$_{15}$ S$_{35}$) thin film. The Ag Polarized photodoping result in reducing the time of saturation anisotropy and increasing the sensitivity of linearly anisotropy intensity As the results, the Ag polarized photodoping will be have a capability of new method that suggests more improvement of photoinduced anisotropy property in the thin films of chalcogenide.ogenide.ide.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.1
• /
• pp.27-30
• /
• 2012

This paper proposes a micro gas sensor for measuring $H_2S$ gas. This is based on a $SnO_2$-CuO multi-layer thin film. The sensor has a silicon diaphragm, micro heater, and sensing layers. The micro heater is embedded in the sensing layer in order to increase the temperature to an operating temperature. The $SnO_2$-CuO multi layer film is prepared by the alternating deposition method and thermal oxidation which uses an electron beam evaporator and a thermal furnace. To determine the effect of the number of layers, five sets of films are prepared, each with different number of layers. The sensitivities are measured by applying $H_2S$ gas. It has a concentration of 1 ppm at an operating temperature of $270^{\circ}C$. At the same total thickness, the sensitivity of the sensor with multi sensing layers was improved, compared to the sensor with one sensing layer. The sensitivity of the sensor with five layers to 1 ppm of $H_2S$ gas is approximately 68%. This is approximately 12% more than that of a sensor with one-layer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.7
• /
• pp.525-529
• /
• 2010

In this paper, the characteristics of a thin-type ultrasonic motor generating elliptical displacements analyzed by FEM are presented, and then fabrication of the motor is then described. The structure of the motor consists of sixteen ceramic pieces attached to the upper and bottom surfaces of an elastic body. The principle of the motor is to apply alternating voltages which have a 90 phase difference to the attached ceramics, and then elliptical displacements are generated at four edges of the elastic body. Then the rotor is moved by the elliptical displacements. In the case of a ceramic thickness of 1.5, the highest speed was obtained at 79 kHz. In the case of a ceramic thickness of 2 mm, the highest speed was obtained at 77.5 kHz. Consequently, the speed and torque of the ultrasonic motor (USM) increased linearly with increasing applied voltage.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.415-415
• /
• 2010

면방전 구조의 AC-PDP는 페닝 혼합 기체 중에서 Xe 플라스마에서 발생되는 VUV (Vacuum Ultra Violet) 에 의해 들뜬 형광체로부터 가시광이 발생된다. Xe 여기종은 828 nm의 공명준위를 거쳐 147 nm의 진공자외선을 방출하며 823 nm의 준안정준위에서 분자선을 거쳐 173 nm의 진공 자외선을 낸다. 이러한 Xe 여기종의 밀도를 측정하기 위해서는 828 nm와 823 nm의 레이저를 외부에서 인위적으로 조사하여 측정하면 IR (Infrared)의 흡수전과 흡수후의 빛의 세기로 Xe 여기종의 밀도 및 분포를 계산할 수 있다. 본 실험에서는 823 nm에 초점을 두었으며 LAS (Laser Absorption Spectroscopy) 기법을 통하여 He-Ne-Xe(15%, 20 %, 30%) 400Torr의 3종 기체의 Xe 함량에 따른 시공간의 Xe($1s_5$) 여기종 밀도 분포와 방전효율을 관측하였다. 최근 3전극 면방전형 AC-PDP 효율 향상을 위해 3종 기체의 Xe함량비의 방전기체에 대한 연구가 수행되고 있다. 이러한 기초 데이터는 혼합기체 조건에 따른 면방전 구조의 3전극 AC-PDP의 발광 효율을 개선하는 데 유용한 자료로 활용될 것이다.

• Journal of Korea Water Resources Association
• /
• v.35 no.3
• /
• pp.251-259
• /
• 2002

Flow characteristics occurring a side-weir overflow in rectangular channel is investigated in this study. A numerical model based on the two -dimensional shallow-water equations is employed to review the factors influencing on the side- weir overflow discharge and the change of flow depths and velocities. It is found that the discharge coefficient which has the most significant influence on the overflow is affected by geometric characteristics of a side-weir, Froude number of the main channel flow and the flow depth of the main channel at the starting point of a side-weir. And the discharge coefficient applicable to a practical design of a side-weir is proposed by deriving a relationship between Froude number of the main channel flow at the starting point of a side-weir and Froude number of the main channel flow.