• 한국재료학회지
• /
• 제22권11호
• /
• pp.609-614
• /
• 2012

We report on the NO gas sensing properties of non-directional ZnO nanofibers synthesized using a typical electrospinning technique. These non-directional ZnO nanofibers were electrospun on an $SiO_2$/Si substrate from a solution containing poly vinyl alcohol (PVA) and zinc nitrate hexahydrate dissolved in distilled water. Calcination processing of the ZnO/PVA composite nanofibers resulted in a random network of polycrystalline ZnO nanofibers of 50 nm to 100 nm in diameter. The diameter of the nanofibers was found to depend primarily on the solution viscosity; a proper viscosity was maintained by adding PVA to fabricate uniform ZnO nanofibers. Microstructural measurements using scanning electron microscopy revealed that our synthesized ZnO nanofibers after calcination had coarser surface morphology than those before calcination, indicating that the calcination processing was sufficient to remove organic contents. From the gas sensing response measurements for various NO gas concentrations in dry air at several working temperatures, it was found that gas sensors based on electrospun ZnO nanofibers showed quite good responses, exhibiting a maximum sensitivity to NO gas in dry air at an operating temperature of $200^{\circ}C$. In particular, the non-directional electrospun ZnO nanofiber gas sensors were found to have a good NO gas detection limit of sub-ppm levels in dry air. These results illustrate that non-directional electrospun ZnO nanofibers are promising for use in low-cost, high-performance practical NO gas sensors.

• The Korean Journal of Ceramics
• /
• 제4권4호
• /
• pp.304-310
• /
• 1998

Carbothermal reduction has been one of the important processes for the production of ceramic raw materials such as silicon carbide, silicon nitride, boron carbide, etc. The process has also been one of several trials for the recovery of ZnO from ZnO-containing waste. It usually involves two consecutive steps: the evolution of Zn vapor and its oxidation with air. In this study a ZnO-containing raw material is reduced by carbon at $1250^{\circ}C$ and the evolved Zn vapor is oxidized with air, resulting in fine powders of ZnO. computer programs, THERMO and PYROSIM developed by MINTEK, are used to simulate the process thermodynamically and the results are compared with the experimental results. It is shown that the ZnO-containing raw material can be reduced and can form fine ZnO with the yield as high as 98.7% under a proper condition. Based on these results, a process is engineered for the production of ZnO in a rotary kiln at a rate of 3 tons/day. The produced ZnO powders show properties suitable to the usual applications in ceramic industries with a purity of > 95wt% and an average particle size of ∼3${\mu}m$.

• Transactions on Electrical and Electronic Materials
• /
• 제18권3호
• /
• pp.155-158
• /
• 2017

In this paper, ZnO Thin Film Transistors (TFTs) were fabricated by a sol-gel method using a low-temperature process, and their physical and electrical characteristics were analyzed. To lower the process temperature to $200^{\circ}C$, we used a zinc nitrate hydrate ($Zn(NO_3)_2{\cdot}xH_2O$) precursor. Thermo Gravimetric Analyzer (TGA) analysis showed that the zinc nitrate hydrate precursor solution had 1.5% residual organics, much less than the 6.5% of zinc acetate dihydrate at $200^{\circ}C$. In the sol-gel method, organic materials in the precursor disrupt formation of a high-quality film, and high-temperature annealing is needed to remove the organic residuals, which implies that, by using zinc nitrate hydrate, ZnO devices can be fabricated at a much lower temperature. Using an X-Ray Diffractometer (XRD) and an X-ray Photoelectron Spectrometer (XPS), $200^{\circ}C$ annealed ZnO film with zinc nitrate hydrate (ZnO (N)) was found to have an amorphous phase and much more oxygen vacancy ($V_o$) than Zn-O bonds. Despite no crystallinity, the ZnO (N) had conductance comparable to that of ZnO with zinc acetate dihydrate (ZnO (A)) annealed at $500^{\circ}C$ as in TFTs. These results show that sol-gel could be made a potent process for low-cost and flexible device applications by optimizing the precursors.

• 폴리머
• /
• 제38권3호
• /
• pp.299-306
• /
• 2014

ZnO pillared saponite was synthesized via a microwave hydrolysis method. To enhance interfacial compatibility between zinc oxide (ZnO) pillared saponite and poly lactic acid (PLA), ZnO pillared organic saponite was prepared by intercalation modification of cetyltrimethylammonium bromide. Moreover, PLA/ZnO pillared organic saponite nanocomposites were prepared by melting processing. The microstructure analysis of PLA/ZnO pillared organic saponite nanocomposites showed that ZnO pillared organic saponite was exfoliated and homogeneouslydispersed in PLA matrix. The property results showed that ZnO pillared organic saponite improved the mechanical properties and thermal stabilities of PLA/ZnO pillared organic saponite nanocomposites. Differential scanning calorimetry (DSC) demonstrated that ZnO pillared organic saponite restrained the appearance of cold crystallization, lowered the glass transition temperature and melting temperature of PLA, and improved the crystallinity of PLA. The results demonstrated that ZnO pillared organic saponite had a good interfacial compatibility and heterogeneous nucleation effect in PLA matrix, and also played an active role in accelerating the crystallization process of PLA.

• 한국결정성장학회지
• /
• 제22권1호
• /
• pp.15-18
• /
• 2012

Transparent conductive indium zinc oxide thin films were prepared by spin-coating a sol-gel solution. Zinc acetate dihydrate [$Zn(CH_3COO)_2{\cdot}2H_2O$] and indium acetate [In$(CH_3COO)_3$] were used as starting precursors, and 2-methoxyethanol with 1-propanol as solvents. Upon annealing in a temperature range from 500 to $1000^{\circ}C$, the thin film crystallizes into polycrystalline $In_2O_3$(ZnO). The lowest electrical resistivity was obtained at an annealing temperature of $700^{\circ}C$ as $2{\Omega}{\cdot}cm$. Average optical transmittances were higher than 80% at all annealing temperatures. These experimental results confirm that the sol-gel spin-coating can be a good simplified practical method for forming transparent electrodes.

• 한국응용과학기술학회지
• /
• 제40권5호
• /
• pp.1116-1125
• /
• 2023

산화아연 막은 투명한 전도성 물질로써 다양한 분야의 광전자소자에 이용되고 있다. 그러므로 산화아연 막의 특성을 규명하는 것은 광전자소자의 성능을 높이는데 매우 중요한 역할을 할 것이다. 본 논문에서는 이러한 산화아연 막을 용액공정 기반으로 제작하여 형태적, 구조적 특성을 평가하고자 한다. 구체적으로는 졸-겔 방법을 반복적으로 시행하여, 시행 횟수에 따른 산화아연 막의 물성의 변화를 관찰할 것이다. 일정한 용액 조건하에서, 5회의 반복적인 졸-겔 방법을 시행한 결과 결정화가 진행되는 것을 확인하였다. 7회 이상에서는 원소 구성 및 결정화도가 특정 값에 수렴하는 경향을 보였다. 최종적인 산화아연 막의 평균결정의 크기는 약 10.7 nm 정도로 계산되었다. 본 연구를 통해 최적의 결정화를 보이는 공정횟수는 7회였다. 본 연구 결과 및 방법론은 다양한 용액공정 변수를 가변시키면서 적용할 수가 있고 최적의 공정조건을 확립하는데 기여할 것으로 기대한다.

• 반도체디스플레이기술학회지
• /
• 제20권4호
• /
• pp.1-5
• /
• 2021

Field-effect transistors based on solution-processed metal oxide semiconductors has attracted huge attention due to their intrinsic characteristics of optical and electrical characteristics with benefits of simple and low-cost process. Especially, spray-pyrolysis has shown excellent device performance which compatible to vacuum-processed Field-effect transistors. However, the high annealing temperature for crystallization of MOS and narrow range of precursors has impeded the progress of the technology. Here, we demonstrated the nc-ZnO/ZnO films performed by spray-pyrolysis with incorporating ZnO nanoparticles into typical ZnO precursor. The films exhibit preserving morphological properties of poly-crystalline ZnO and enhanced electrical characteristics with potential for low-temperature processability. The influence of nanoparticles within the film was also researched for realizing ZnO films providing good quality of performance.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.235.2-235.2
• /
• 2015

The front transparent conductive oxide (TCO) films must exhibit good transparency, low resistivity and excellent light scattering properties for high efficiency amorphous silicon (a-Si) thin film solar cells. The light trapping phenomenon is limited due to non-uniform and low aspect ratio of the textured glass [1]. We present the low cost electrochemically deposited uniform zinc oxide (ZnO) nanorods with various aspect ratios for a-Si thin film solar cells. Since the major drawback of the electrochemically deposited ZnO nanorods was the high sheet resistance and low transmittance that was overcome by depositing the RF magnetron sputtered AZO films as a seed layer with various thicknesses [2]. The length and diameters of the ZnO nanorods was controlled by varying the deposition conditions. The length of ZnO nanorods were varied from 400 nm to $2{\mu}m$ while diameter was kept higher than 200 nm to obtain different aspect ratios. The uniform ZnO nanorods showed higher haze ratio as compared to the commercially available FTO films. We also observed that the scattering in the longer wavelength region was favored for the high aspect ratio of ZnO nanorods and much higher aspect ratios degraded the light scattering phenomenon. Therefore, we proposed our low cost and uniform ZnO nanorods for the high efficiency of thin film solar cells.

• 공업화학
• /
• 제21권2호
• /
• pp.224-229
• /
• 2010

Transparent conducting oxide (TCO) 박막은 평판 디스플레이 산업에 널리 사용되고 있다. 화학적으로 우수한 투명전도성 Indium Zinc Oxide (IZO) 필름은 Indium Tin Oxide (ITO) 필름의 대체 물질로 관심을 끌고 있다. 본 연구에서는 90 : 10 wt%의 $In_2O_3$와 ZnO를 혼합하여 만든 타겟으로 전자빔 증착법을 이용하여 polynorbornene (PNB) 기판 위에 IZO 박막을 제조하였다. UV/Visible spectrophotometer, 4-Point Probe를 이용하여 증착 두께와 산소도입 속도에 따른 IZO 필름의 전기적 및 광학적 특성을 연구하였으며, SEM, XRD 및 XPS를 이용하여 증착된 IZO의 구조적 특성 및 표면조성비를 연구하였다.

• The Korean Journal of Ceramics
• /
• 제3권4호
• /
• pp.269-273
• /
• 1997

Chemical composition of cement powder influences the setting time and early compressive strength development. The setting time increases as the amounts of zinc oxide and magnesium oxide are increased. For one day compressive strength development, a cement powder with a composition 90% ZnO, 8% MgO and 2% silica resulted in the highest strength (greater than 1, 090 kg/$\textrm{cm}^2$). Cement-forming liquids also need to be buffered, with both aluminum and zinc ions, for a good consistency and a higher strength of the zinc phosphate cement. These liquids control the setting reactions.