• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.4
• /
• pp.87-96
• /
• 2004

As a special concrete, which is a mixture of soil, cement and water, has strength like regular concrete for pavement, soil cement has been used in various field such as pavement and soft soil improvement. The objective of this study was to investigate the characteristic of unconfined compressive strength and time dependent behavior of soil cement that is made from decomposed granite soil or coluvial and inorganic solidification liquid. The results showed that the unconfined compressive strength appears to increase as the amount of cement and curing time increase In addition, the strength seems to decrease with increase of the potion of fine particles(No 200 sieve). The result of XRD indicated that there is Vermiculite, the product of reaction, in the soil cement. The dynamic properties of material, such as shear complex compliance, shear complex modulus, and phase angle could be calculated from the hysteresis loop obtained from the Haversine Creep Tests. Finally, creep behavior was able to be predicted from these dynamic properties.

• Analytical Science and Technology
• /
• v.21 no.2
• /
• pp.123-128
• /
• 2008

The golden turbid solution of cordierite precursor was obtained by using magnesium ethoxide in sol-gel method, while the clear solution of cordierite precursor was obtained when 5%-$Zr(OC_3H_7)_4$ solution was used in the sol-gel reaction. $SiO_2$ component was confirmed by infrared spectra showing $1045cm^{-1}$ and the stretching vibration of gelish $SiO_4$ showed $1140cm^{-1}$ and $940cm^{-1}$. The component of $Al_2O_3$ showed at $580cm^{-1}$ and network structure of $Al_2O_6$ showed at $680cm^{-1}$. The component of MgO was confirmed at $575cm^{-1}$ as the stretching vibration. X-ray diffraction analysis showed ${\mu}$-cordierite crystal was showed up at temperature above $1000^{\circ}C$ at the mole ratio of cordierite precursor and water (1:5). ${\mu}$-Cordierite and ${\alpha}$-cordierite were coexisted at $1050^{\circ}C$ for the mole ratio of cordierite precursor and ammonia (1:5) while ${\alpha}$-cordierite was only existed at $1100^{\circ}C$ for the same mole ratio as mentioned above.

• The Journal of Korean Society for Radiation Therapy
• /
• v.19 no.2
• /
• pp.99-106
• /
• 2007

Purpose: The patient's position and anatomy during the treatment course little bit varies to some extend due to setup uncertainties and organ motions. These factors could affected to not only the dose coverage of the gross tumor but over dosage of normal tissue. Setup uncertainties and organ motions can be minimized by precise patient positioning and rigid immobilization device but some anatomical site such as prostate, the internal organ motion due to physiological processes are challenge. In planning procedure, the clinical target volume is a little bit enlarged to create a planning target volume that accounts for setup uncertainties and organ motion as well. These uncertainties lead to differences between the calculated dose by treatment planning system and the actually delivered dose. The purpose of this study was to evaluate the differences of interfractional displacement of organ and GTV based on the tomoimages. Materials and Methods: Over the course of 3 months, 3 patients, those who has applied rectal balloon, treated for prostatic cancer patient's tomoimage were studied. During the treatment sessions 26 tomoimages per patient, Total 76 tomoimages were collected. Tomoimage had been taken everyday after initial setup with lead marker attached on the patient's skin center to comparing with C-T simulation images. Tomoimage was taken after rectal balloon inflated with 60 cc of air for prostate gland immobilization for daily treatment just before treatment and it was used routinely in each case. The intrarectal balloon was inserted to a depth of 6 cm from the anal verge. MVCT image was taken with 5 mm slice thickness after the intrarectal balloon in place and inflated. For this study, lead balls are used to guide the registration between the MVCT and CT simulation images. There are three image fusion methods in the tomotherapy, bone technique, bone/tissue technique, and full image technique. We used all this 3 methods to analysis the setup errors. Initially, image fusions were based on the visual alignment of lead ball, CT anatomy and CT simulation contours and then the radiation therapist registered the MVCT images with the CT simulation images based on the bone based, rectal balloon based and GTV based respectively and registered image was compared with each others. The average and standard deviation of each X, Y, Z and rotation from the initial planning center was calculated for each patient. The image fusions were based on the visual alignment of lead ball, CT anatomy and CT simulation contours. Results: There was a significant difference in the mean variations of the rectal balloon among the methods. Statistical results based on the bone fusion shows that maximum x-direction shift was 8 mm and 4.2 mm to the y-direction. It was statistically significant (P=<0.0001) in balloon based fusion, maximum X and Y shift was 6 mm, 16mm respectively. One patient's result was more than 16 mm shift and that was derived from the rectal expansions due to the bowl gas and stool. GTV based fusion results ranging from 2.7 to 6.6 mm to the x-direction and 4.3$\sim$7.8 mm to the y-direction respectively. We have checked rotational error in this study but there are no significant differences among fusion methods and the result was 0.37$\pm$0.36 in bone based fusion and 0.34$\pm$0.38 in GTV based fusion.

• Journal of the Korea Concrete Institute
• /
• v.29 no.3
• /
• pp.275-281
• /
• 2017

This study examined the effect of water-to-binder ratio (W/B) and phosphate-to-binder ratio (P/B) on the flow, setting time, compressive strength development, and pH variation of magnesium-potassium phosphate composites, MKPC mortars. Ten mortars mixtures were prepared with the W/B varying from 20% to 40% at each P/B of 0.3 or 0.5. The hydration products and microstructural pore distribution of the MKPC pastes were investigated using X-ray diffraction (XRD), scanning electron microscope (SEM) and mercury intrusion porosimetry (MIP). The initial flow and setting time of MKPC mortars tended to decrease with an increase of P/B, indicating that the final setting time was shortened by approximately 24% when P/B increased from 0.3 to 0.5. The slope of the early-strength development measured in the MKPC mortars was considerably higher than that of cement concrete specified in code provisions. For obtaining a relatively good 28-day strength (above 30 MPa) and a near neutral pH (below 9.0) in MKPC mortars, the P/B and W/B need to be selected as 0.5 and 30%, respectively. The strubite-K crystal increased with the increases of P/B and W/B, which leads to the decrease of the macro-capillary pores.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.165-165
• /
• 2010

$1.55\;{\mu}m$ 대역의 레이저 다이오드를 제작하기 위해, InP(001) 기판에 InAlGaAs 물질을 장벽층으로 하는 InAs 양자점 구조를 분자선증착기 (MBE)를 이용하여 성장하고 구조 및 광학적 특성을 Double Crystal X-ray Diffraction (DCXRD), Atomic Force Microscopy (AFM), Photoluminescence (PL)을 이용하여 평가하였다. 일반적으로 InAlGaAs 물질은 고유한 상분리 현상 (Phase Separation)이 나타나는 특성이 있으며, 이는 양자점 성장에 중요한 요인으로 작용할 수 있다. 이러한 InAlGaAs 물질의 상분리 현상을 기판온도 ($540^{\circ}C$, $555^{\circ}C$, $570^{\circ}C$)를 비롯한 성장변수를 변화시켜 제어하고 InAs 양자점 형성에 어떠한 영향을 미치는지를 분석하였다. 540의 성장온도에서 InP(001) 기판에 격자정합한 InAlGaAs 장벽층이 성장온도를 $570^{\circ}C$로 증가시킬 경우 기판에 대하여 인장 응력 (Tensile Strain)을 받는 구조로 변화되었다. 인장응력을 받는 InAlGaAs 장벽층을 Ga Flux 양을 조절하여 격자정합한 InAlGaAs 층을 형성할 수 있었다. AFM을 통한 표면 형상 분석 결과, 서로 다른 기판온도에서 성장한 InAlGaAs 물질이 InP(001) 기판에 격자정합 조건일지라도 표면의 거칠기 (Surface Roughness)는 매우 다른 양상을 보였고 InAs 양자점 형성에 직접적으로 영향을 주었다. $570^{\circ}C$에서 성장한 InAlGaAs 위에 형성한 InAs 양자점의 가로방향 크기를 세로방향 크기로 나눈 비율이 1.03으로서, 555와 $540^{\circ}C$의 1.375 와 1.636와 비교할 때 모양 대칭성이 현저히 개선된 것을 알 수 있다. 상분리 현상이 줄어 표면 거칠기가 좋은 InAlGaAs 위에 양자점을 형성할 때 원자들의 이동도가 상대적으로 높아 InAs 양자점의 크기가 증가하고, 밀도가 감소하는 현상이 나타났다. 또한 InAlGaAs 장벽층이 InP(001) 기판을 기준으로 응력 (Compressive 또는 Tensile)이 존재하는 경우, InAs 양자점 모양이 격자정합 조건 보다 비대칭적으로 변하는 특성을 보여 주었다. 이로부터, 대칭성이 개선된 InAs 양자점 형성에 InAlGaAs 장벽층의 표면 거칠기와 응력이 중요한 변수로 작용함을 확인 할 수 있었다. PL 측정 결과, 발광파장은 $1.61\;{\mu}m$로 InAs 양자구조 형상에 따라 광강도 (Intensity), 반치폭 (Line-width broadening) 등이 변화 되었다.

• Korean journal of communication and information
• /
• v.38
• /
• pp.211-244
• /
• 2007

Article 17 and 18 of the Korean Constitution respectively prescribe the violation of individual's right to privacy and the secrecy of wire communication. Meanwhile, Article 20 of the Criminal Code provides that an act which is conducted within the ambit of laws or pursuant to accepted business practices or which does not violate the social norms shall not be punishable. In 1999, the Constitutional Court held that media reports on public matters of public figures must be given strong constitutional protection, and treated differently from reports on private matters of private figures. In accordance with the decision, the Supreme Court has expanded the scope of constitutional guarantee of freedom of expression since 2002. This study analyzes the issue of media liability for publication of illegally intercepted wire communication by a third person. Particularly, it reviews Seoul High Court's ruling on 'X-file scandal' which disclosed intercepted wire communications between notable public figures regarding a slush fund for a presidential candidate. In the light of this analysis, the study concludes that the media reporting of the intercepted communication does not violate social norms of Article 20, and therefore it is entitled to a constitutional privilege.

• Journal of the Korean Magnetics Society
• /
• v.21 no.3
• /
• pp.88-92
• /
• 2011

We grew $Zn_{0.4}Fe_{2.6}O_4$ thin films using Pulsed Laser Deposition and studied their crystal structure and magnetical characteristics as a function of growth temperature ($T_g$). For the film with $T_g=300^{\circ}C$, X-ray reflections from ${\alpha}-Fe_2O_3$ and ZnO were observed. However, when $T_g$ was increased from 300 to $500^{\circ}C$, crystal structure of inverse spinel was stabilized with the crystal orientation of $Zn_{0.4}Fe_{2.6}O_4(111)/Al_2O_3(0001)$ without any detection of ${\alpha}-Fe_2O_3$ and ZnO phases. The surface morphology shows flattening behavior with increasing $T_g$ from 300 to $500^{\circ}C$. These observations indicate that Zn is substituted into tetrahedron A-site of the inverse-spinel $Fe_3O_4$. M-H curves exhibit clear ferromagnetism for the sample with $T_g=500^{\circ}C$ whereas no ferromagnetism is observed for the film with $T_g=300^{\circ}C$.

• Journal of the Korean Chemical Society
• /
• v.25 no.6
• /
• pp.367-375
• /
• 1981

Single crystals of Potassium Sulfate ($K_2SO_4$) have been grown from the saturated solution by the evaporation method at the optimum conditions. Radiation damages in the crystal by ${\gamma}$-irradiation of about $12{\times}10^6$ Roentgen have given rise to paramagnetic centers or paramagnetic defects. Electron spin resonance (ESR) spectra of the centers are obtained with the X-band EPR spectrometer at room temperature. The ESR peaks of the paramagnetic species are found to be anisotropic but the peak of $SO_3-$ radical is an isotropic of Gaussian shape at g = 2.0036. A number of ESR spectra of the crystal for angular variation of the anisotropic peaks are recorded at various orientations of rotation about a, b and c crystallographic axes respectively. The g-values are calculated from the line position between anisotropic peaks and the isotropic one and then principal g-values and its direction cosines of the species are obtained by diagonalization of 9 matrix elements of the corresponding g-values. All the paramagnetic defects are identified by the characteristic principal g-values and its direction cosines.

• Applied Chemistry for Engineering
• /
• v.32 no.1
• /
• pp.83-90
• /
• 2021

In this study, effects of the physical and chemical properties of low temperature heated carbon on electrochemical behavior as a secondary battery anode material were investigated. A heat treatment at 600 ℃ was performed for coking of petroleum based pitch, and the manufactured coke was heat treated with different heat temperatures at 700~1,500 ℃ to prepare low temperature heated anode materials. The physical and chemical properties of carbon anode materials were studied through nitrogen adsorption and desorption, X-ray diffraction (XRD), Raman spectroscopy, elemental analysis. Also the anode properties of low temperature heated carbon were considered through electrochemical properties such as capacity, initial Coulomb efficiency (ICE), rate capability, and cycle performance. The crystal structure of low temperature (≤ 1500 ℃) heated carbon was improved by increasing the crystal size and true density, while the specific surface area decreased. Electrochemical properties of the anode material were changed with respect to the physical and chemical properties of low temperature heated carbon. The capacity and cycle performance were most affected by H/C atomic ratio. Also, the ICE was influenced by the specific surface area, whereas the rate performance was most affected by true density.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.2
• /
• pp.33-39
• /
• 2015

$BaTiO_3$ is typical ferromagnetic materials with dielectric constant of above 200. $BaTiO_3$ nanoparticles applications are available for multiple purposes such as nanocapacitors, ferroelectric random access memories, and so on. Applications are is diverse from the dispersion of nanoparticles depending on the route of synthesis. In this study, $BaTiO_3$ nanoparticles were synthesized by two different methods such as oxalate method and sol-gel process (ambient condition sol method). Particle size and dispersion condition were studied according to the preparation method and capping agent. Poly vinyl pyrrolidone (PVP) was used as a capping agent in oxalate method and tetrabutylammonium hydroxide (TBAH) used as a capping agent in sol-gel process each. Cubic crystal structure of $BaTiO_3$ phase could be confirmed by X-ray diffraction analysis. Fourier transform-infrared spectroscopy was employed for the confirmation of the capping agent and $BaTiO_3$ nanoparticles. The particle size and distribution analysis was also performed by particles size analyzer and scanning electron microscope.