• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.4
• /
• pp.628-635
• /
• 1999

At center frequency of 11.85 GHz, wideband left-handed circularly polarized microstrip array antenna is designed with the method of sequential ratation based on $2\times2$ radiation elements($0^{\circ}$, $45^{\circ}$, $90^{\circ}$, $135^{\circ}$ phase delay). Its return loss, axial ratio bandwidth, radration pattern, and gain are compared with those adopting sequential rotation based on $1\times2$ radiation elements($0^{\circ}$, $90^{\circ}$, $180^{\circ}$, $270^{\circ}$phase delay). The $8\times8$ array is manufactured and measured. The results show that 10 dB return loss bandwidth is 10.51~12.74GHz(18.82%) which is 1.57 times wider than the case using $1\times2$ sequential rotation method, 3 dB axial ratio bandwidth is 11.43~12.5 GHz(9.03%) which is 1.25 times as wide as that using $1\times2$ sequential rotation method and the antennal gain is 25.4 dB. The results of mesurements are almost similar to those of simulation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.6
• /
• pp.119-124
• /
• 2008

Transimpedance amplifier(TIA) is the most significant element to determine the performance of the optical receiver, and thus the TIA must satisfy tile design requirements of high gain and wide bandwidth. In f)is paper, we propose a novel single chip optical receiver that exploits an analog adaptive equalizer and a limiting amplifier to enhance the gain and bandwidth performance, respectively. The proposed optical receiver is designed by using a $0.13{\mu}m$ CMOS process and its post-layout simulations show $120dB{\Omgea}$ transimpedance gain and 5.88GHz bandwidth. The chip core occupies the area of $0.088mm^2$, due to utilizing the negative impedance converter circuit rather than using on-chip passive inductors.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1208-1213
• /
• 2010

In this paper, a microstrip balun-BPF of slotted-square-patch type is proposed. The conventional balun-BPF has some drawbacks of narrow bandwidth and high insertion loss. In order to improve these weak points, we used a square patch in designing balun-BPF on which two slots intersecting perpendicularly and one corner-edge perturbation are adopted. This structure allows one of the most effective use of the patch space so that the insertion loss can be decreased. Changing the slot lengths is use to control the operating frequency and the bandwidth of the balun-BPF. A fabricated balun-BPF shows wide bandwidth of 300 MHz(12.7 %), small insertion loss of 0.56 dB, phase difference of $184^{\circ}{\pm}15^{\circ}$ and amplitude imbalances of within 1 dB between two output ports at 2.4 GHz band.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.5
• /
• pp.251-258
• /
• 2002

In this paper, the dipole-fed planar array antenna applied Yagi-Uda antenna away theory to microstrip antenna is designed and fabricated at X-band. The design procedure of the dipole-fed planar array antenna with the wide bandwidth is presented to be easily practiced to a wireless communication system. The radiation pattern, return loss and bandwidth of the antenna are improved by the finite differential time domain(FDTD) numerical method. The propriety of analysis of planar dipole antenna is proved from the measured data. From the measured results, the antenna maximum gain is 4.9dBi at center frequency of 10GHz and frequency bandwidth is about 40%. Front-to-back ratio is 16dB, and half-power beam-width of E-plane and H-plane are 117$^{\circ}$and 156$^{\circ}$, respectively. When VSWR of antenna is less than 2, the measured results are agreed well with the theoretical values in the frequency range from 7.4GHz to 11.88GHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.3B
• /
• pp.204-211
• /
• 2012

Wireless Mesh Network (WMN) has drawn much attention due to wide service coverage with low system cost. However, WMN suffers from high bit error rate, which provides different link capacity among wireless mesh routers. The conventional routing metrics select the path based on link quality. The link with the best quality is preferred as the data transmission path, and they becomes the bottleneck links, which leads to network performance degradation. In this paper, we propose a routing metric that considers the available bandwidth and the number of nodes suffering congestion in the path. Through computer simulations, we verified that the proposed routing metric outperforms the existing routing metrics in terms of average transmission delay, packet loss, system throughput.

• Journal of Broadcast Engineering
• /
• v.10 no.2
• /
• pp.182-189
• /
• 2005

In this paper, an asymmetric WDM-EPON transmission scheme is proposed to be used in a high speed access network system, which is required to implement the convergence of broadcast and communication. WDM is used for downstream transmission from OLT to access nodes, satisfying wide bandwidth requirement for broadcasting and various multimedia services. And an EPON scheme, which is cheaper than WDM, is applied to upstream transmission where less bandwidth is required. A transmission test in physical layer was performed successfully and the results are provided. If ONUs are to be used in a home gateway, its protocol should be appropriate to its traffic pattern. Voice is sensitive to a time delay while data is not. A new dynamic bandwidth assignment protocol for PON system, which can cope with various types of data in access network is proposed and its performance is analysed. A maximum cycle time is specified to achieve the QoS of signals sensitive to time delay. And a minimum window is specified to prevent the downstream control signals from uprising. It is shown by simulation that the proposed EPON protocol can provide a better performance than previous ones.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.2 s.58
• /
• pp.38-49
• /
• 2006

In order to increase the spectrum efficiency, recently, there is the number of studies for CR technology. For instance, IEEE 802.22 WRAN(Wireless Regional Area Network) WG considered the CR technology as a solution of WRAN system to serve the high speed internet service(1.5 Mbps down stream and 384 kbps up stream) in 100 km overall coverage and 54 MHz-746 MHz band. Basically, in MAC point of view, the WRAN system have been standardizing based on the IEEE 802.16 MAC layer features such as Data transmission method, QoS provision and Bandwidth request schemes. Additionally, the WRAN system further include CR nature functions such as incumbent user protection, self coexistence which would be importantly considered. Also, the inherent WRAN functions are added such as channel bonding and fractional bandwidth usage. This paper mainly explained frame structure, IU protection, self coexistence which are key functions of WRAN system. Finally, in this paper, we expressed a prospect of IEEE 802.22 WRAN standardization.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.45-51
• /
• 2011

This paper presents a wideband low-noise amplifier (LNA) covering 800MHz~5.8GHz for various wireless communication standards by utilizing in a 0.13um CMOS technology. Particularly, the LNA consists of two stages to improve the low-noise characteristics, that is, a cascode input stage and an output buffer with noise cancellation technique. Also, a feedback resistor is exploited to help achieve wideband impedance matching and wide bandwidth. Measure results demonstrate the bandwidth of 811MHz~5.8GHz, the maximum gain of 11.7dB within the bandwidth, the noise figure of 2.58~5.11dB. The chip occupies the area of $0.7{\times}0.9mm^2$, including pads. DC measurements reveal the power consumption of 12mW from a single 1.2V supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.12
• /
• pp.1044-1052
• /
• 2016

In this paper, a cavity back slot antenna with a rotated rectangular patch is proposed. The proposed antenna consists of a ground plane with cavity structure, a microstrip feed line, and a rectangular patch with slot. With a dimension of $55mm{\times}40mm{\times}10mm$, the proposed antenna has the wide bandwidth due to the cavity structure. Measured 10 dB return loss bandwidth and fractional bandwidth of the proposed antenna is 5,030 MHz(3.02~8.05 GHz) and 90.9 % at the center frequency of 5.05 GHz. The proposed antenna is designed and simulated using ANSYS HFSS v.15.0.0. The designed antenna is fabricated and tested to validate its performances.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.12
• /
• pp.171-176
• /
• 2005

This study designed and fabricated a multi-purpose planar antenna for base stations that are accessible to DCS, WiBro, and ISM. The proposed antenna was designed into an open loop form from the existing monopole structure. The capacitance of the multi-purpose antenna was increased by the coupling of open parts. This makes the use of MMIC and LTCC convenient and the antenna is smaller and has a larger gain than existing antennas. The resonance distance and bandwidth can be adjusted by changing the open gap and the height of the loop of the antenna. The bandwidth of the designed antenna satisfies DCS, IMT-2000, WiBro, Bluetooth, wireless LAN and ISM bands based on VSWR 2. The entire frequency bandwidth is $58.75\%$ of $1.575GHz\~2.985GHz(1.41GHz)$. Also, the radiation pattern of the antenna displayed co-polarization and cross-polarization characteristics at 1.6GHz, 2.3GHz and 2.8GHz.