• Journal of the Korean Institute of Intelligent Systems
• /
• v.21 no.6
• /
• pp.679-685
• /
• 2011

This paper presents an algorithm identifying devices that generate observed mixed signals that are collected at main power-supply line. The proposed algorithm, which is necessary for low cost electric power monitoring system at appliance-level, that is non-intrusive load monitoring system, divides incoming mixed signal into multiple time intervals, calculating difference-signals between consecutive time interval, and identifies which device is operating at the time interval by analysing the difference-signals. Since the features of one device can remain when the time interval is short enough and the features are independent and additive, well-known classification algorithms can be used to classify the difference-signals with features of N individual devices, otherwise $2^N$ features might be necessary. The proposed algorithm was verified using data mixed in a laboratory with individual devices's data collected from field. When maximum 4 devices operate or stop sequentially and when features satisfy the requirements of proposed algorithm, the proposed algorithm resulted nearly 100% success rate under the constrained test condition. In order to apply the proposed algorithm in real world, the number devices shall increase, the time interval shall be smaller and the pattern of mixture shall be more diverse. However we can expect, if features used follow guidelines of proposed algorithm, future system could have certain level of performance without the guideline.

• Journal of the Korea Institute of Building Construction
• /
• v.6 no.1 s.19
• /
• pp.101-107
• /
• 2006

While a Study with regard to the measurement on Concrete Strength and the Change of Drying Shrinkage in accordace with Content Ratio of Crushed Stone Powder, it is being analyzed as the result that the strength according to Content Ratio of crushed Stone Powder is somewhat lowering. Accordingly, it is the real situation that the Concrete mixed with Crushed Stone Powder is utilized for non-structural material, not for the structural material. Therefore, this Research willing to furnish the suitable utilizing scheme for construction site as well as practical life by means of conduct the experiment on both Concrete Pressure Strength according to mixture with Crushed Stone Powder and Elastic Modulus, it also presumes the optimum Elastic Modulus Equation after analysis of comparison with common concrete strength. As the result of the experiment, in case of the Content Ratio of Crushed Stone Powder is less than 5%, it did not display a big difference in its both strength and matter-property compare with common concrete. In case of Elastic Modulus, when the Pressure Strength is 50% and 40% respectively, the Elastic Modulus Equation accords very well with the provided condition of Quadratic function, and as the result of the Presumption on Elastic Modulus according to Content of Crushed Stone Powder, in case the Pressure Strength is 50%, Elastic Modulus Equation showed that Error Ratio of Cubic function is at degree of 0.0005%, in case the Pressure Strength is 40%, Elastic Modulus Equation was accorded well with the value of the experimental data likely as the Error Ratio of Cubic function is at the degree around 0.0034%, respectively.

• Proceedings of the SCSK Conference
• /
• 2003.09b
• /
• pp.149-162
• /
• 2003

Moisturizing the skin is one of the most important functions of skincare cosmetics, because water plays a significant role in keeping the skin healthy. There are various humectants including polyol (glycerin and 1,3-butylene glycol), water-soluble polymers, and botanical extracts. It is well known that the increased amount of polyol in lotion for obtaining high moisturizing effect gives a sticky feeling to the skin. Therefore, a few humectants that can give high moisturizing effect without a sticky feeling for lotion formula is available. On the other hand, oil-based lipstick is well known to have a difficulty to contain a large amount of hydrophilic humectants, because the humectants is unable to be mixed well into oil-based lipsticks and give the lips a peculiar taste. There are newly developed humectants, polyoxyethylene/polyoxypropylene dimethyl ether (EPDME) that can solve these problems describable above. EPDME is a random copolymer of ethylene oxide and propylene oxide. EPDME gives a low sticky feeling with a high moisturizing effect when it is used in lotion. As a remarkable character, EPDME can show not only a preventing effect on rough and dry skin, but also a improving effect upon the use for 1-4 weeks. EPDME can show a synergistic effect with glycerin on preventing to rough and dry skin. Since EPDME can be dissolved in oil-based formulation and used as an ingredient of lipsticks, EPDME can give a moisturizing effect that allows lip to be healthy condition. EPDME can also give no peculiar taste even upon the use of a large amount. EPDME is a useful cosmetic ingredient that can show a good skin care effect in both water-based formula and oil-based formula. EPDME of which polarity can be controllable is expected to be used for various cosmetic applications in near future.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.1
• /
• pp.51-56
• /
• 2016

In this study, for the tube-to-tube friction welding of hose nipple materials, the main parameters of friction welding were investigated using tensile tests, Vickers hardness surveys of the bond area (HAZ), and observations of the microstructure to increase the quality of friction welding based on visual examination. As-welded and post weld heat treated (PWHT) specimens were tested. The optimal welding conditions were found to be n = 1000 rpm, HP = 10 MPa, UP = 15 MPa, HT = 9 s, and UT = 5 s when the metal loss (Mo) was 7.5 mm. Furthermore, the peak of the hardness distribution of the friction welded joints could be eliminated by PWHT. Moreover, the two materials of the friction weld were thoroughly mixed with a well-combined structure of micro-particles, without any molten material, particle growth, or defects.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.4 s.247
• /
• pp.402-408
• /
• 2006

Dissimilar friction welding were produced using 15(mm) diameter solid bar in chrome molybedenum steel(KS SCM440) to carbon steel(KS S45C) to investigate their mechanical properties. The main friction welding parameters were selected to endure good quality welds on the basis of visual examination, tensile tests, Vickers hardness surveys of the bond of area and H.A.Z and microstructure investigations. The specimens were tested as-welded and post-weld heat treated(PWHT). The tensile strength of the friction welded steel bars was increased up to 100% of the S45C base metal under the condition of all heating time. Optimal welding conditions were n=2,000(rpm), $P_1=60(MPa),\;P_2=100(MPa),\;t_1=4(s),\;t_2=5(s)$ when the total upset length is 5.4 and 5.7(mm), respectively. The peak of hardness distribution of the friction welded joints can be eliminated by PWHT. Two different kinds of materials are strongly mixed to show a well-combined structure of macro-particles without any molten material and particle growth or any defects.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.534-537
• /
• 2005

Free Vibration Analysis using Non-dimensional Dynamic Influence Function (NDIF) is extended to arbitrarily shaped plates including polygonal plates. Since the corners of polygonal plates have indefinite normal directions and additional boundary conditions related to a twisting moment at a corner along with moment and shear force zero conditions, it is not easy to apply the NDIF method to polygonal plates wi th the free boundary condition. Moreover, owing to the fact that the local polar coordinate system, which has been introduced for free plates with smoothly varying edges, cannot be employed for the straight edges of the polygonal plates, a new coordinate system is required for the polygonal plates. These problems are solved by developing the new method of modifying a corner into a circular arc and setting the normal direction at the corner to an average value of normal direct ions of two edges adjacent to the corner. Some case studies for plates with various shapes show that the proposed method gives credible natural frequencies and mode shapes for various polygons that agree well with those by an exact method or FEM (ANSYS).

• New & Renewable Energy
• /
• v.3 no.4
• /
• pp.54-62
• /
• 2007

In this paper, we report the research highlight on the preparation and characterization of Indium-free $Cu_2ZnSnSe_4$ and Indium-reduced $CulnZnSe_2$ thin films in order to seek the viability of these absorber materials to be applied in thin film solar cells. The films of $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ were prepared using mixed binary chalcogenides powders. It was observed that Cu concentration was a function of substrate temperature as well as CuSe mole ratio in the target. Under an optimized condition, $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ thin films grew with strong [112]. [220/204] and [312/116] reflections. Both $Cu_2ZnSnSe_4\;and\;CulnZnSe_2$ films were found to exhibit a high absorption coefficient of $104^4cm^{-1}\;Cu_2ZnSnSe_4$ film showed a band gap of 1.5eV which closes to the optimum band gap of an ideal solar absorber for a solar cell. On the other side, an increase of optical band gap from 1.0 to 1.25eV was found to be proportional with an increase of Zn concentration in the $CulnZnSe_2$ film. All films in this study revealed a p-type semiconductor characteristic.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.2
• /
• pp.243-253
• /
• 1999

The dual reciprocity boundary element method (DRBEM) is used to solve the Graetz problem of laminar flow inside circular duct. In this method the domain integral tenn of boundary integral equation resulting from source term of governing equation is transformed into equivalent boundary-only integrals by using the radial basis interpolation function, and therefore complicate domain discretization procedure Is completely removed. Velocity profile is obtained by solving the momentum equation first and then, using this velocities as Input data, energy equation Is solved to get the temperature profile by advancing from duct entrance through the axial direction marching scheme. DRBEM solution is tested for the uniform temperature and heat flux boundary condition cases. Local Nusselt number, mixed mean temperature and temperature profile inside duct at each dimensionless axial location are obtained and compared with exact solutions for the accuracy test Solutions arc in good agreement at the entry region as well as fully developed region of circular duct, and their accuracy are verified from error analysis.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.1166-1171
• /
• 2008

Despite of the increasing number of the application of drilled shaft piles in construction site, most studies on pile capacity have been focused on the side shear resistance. But it is common that the drilled shaft is socketed on the rock so as to use its bearing resistance. The prediction of the end movement and characteristics of the bearing capacity of the pile is great important as well. Therefore, a series of scaled model tests were carried out in order to study the characteristics of the bearing capacity on rock mass. The material of the test block was cement mortar which was mixed with sand, cement and water, and the size of a test block size was $240{\times}240{\times}240mm$. The axial load was applied by a miniaturized pile of 45mm in diameter and flat jacks and steel plate were used for confinement to simulate the real underground loading conditions. The relation of load-displacement was measured in various different conditions of rock mass such as strength, discontinuity of the rock mass and in-situ stress, so q-w curves of the end of the pile were presented for each condition.

• Korean Journal of Health Education and Promotion
• /
• v.26 no.1
• /
• pp.141-158
• /
• 2009

Community-Based Participatory Research(CBPR) has gained attention as a public health approach to develop community health interventions to address health disparities in recognition of the community relevance of specific health issues associated with social determinants of health. It emphasizes community involvement in equal partnership with researchers and public health professionals to address community-identified needs. The characteristics and principles of CBPR discussed in this paper highlight participatory nature, capacity development, partnership building, and process-orientation of CBPR. A 6-step process model for community empowerment is then introduced as a CBPR operationalization strategy. Mixed methods research approaches are valuable in CBPR as well as process evaluation. For the application of CBPR in Korean contexts, the Diffusion of Innovation theory is suggested as a theoretical framework for implementation. Building public health partnerships between public and private sectors to create partnership synergy is a necessary condition for successful CBPR for health promotion in Korea. Accompanying critical factors for the CBPR application include: common understanding of CBPR and its values, establishment of the definition of 'community,' 'community-based' and 'participation' in community health, development of accommodating research infrastructure for CBPR, recognition of the importance of program evaluation (particularly process evaluation), and training CBPR specialists.