• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.5
• /
• pp.470-475
• /
• 2015

This paper presents a wideband Current-Reused Voltage Controlled Oscillator (VCO) with 2-Step Automatic Amplitude Calibration (AAC). Tuning range of the proposed VCO is from 1.95 GHz to 3.15 GHz. The mismatch of differential voltage is within 0.6 %. At 2.423 GHz, the phase noise is -116.3 dBc/Hz at the 1 MHz offset frequency with the current consumption of 2.6 mA. The VCO is implemented $0.13{\mu}m$ CMOS technology. The layout size is $720{\times}580{\mu}m^2$.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.6
• /
• pp.202-207
• /
• 1997

Design and fabrication issues for an L-band GaAs Monolithic Microwave Integrated Circuit(MMIC) Voltage Controlled Oscillator(VCO) as a component of Personal Communications Systems(PCS) Radio Frequency(RF) transceiver are discussed. An ion-implanted GaAs MESFET tailored toward low current and low noise with 0.5mm gate length and 300mm gate width has been used as an active device, while an FET with the drain shorted to the source has been used as the voltage variable capacitor. The principal design was based on a self-biased FET with capacitive feedback. A tuning range of 140MHz and 58MHz has been obtained by 3V change for a 600mm and a 300mm devices, respectively. The oscillator output power was 6.5dBm wth 14mA DC current supply at 3.6V. The phase noise without any buffer or PLL was 93dB/1Hz at 100KHz offset. Harmonic balance analysis was used for the non-linear simulation after a linear simulation. All layout induced parasitics were incorporated into the simulation with EEFET2 non-linear FET model. The fabricated circuits were measured using a coplanar-type probe for bare chips and test jigs with ceramic packages.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.1
• /
• pp.68-72
• /
• 2004

The integrated voltage-controlled-oscillator(VOC) operating at 1.75 ㎓ is designed using the InGaP/GaAs HBT process. The proposed noise removal circuit and FR-4 substrate structure in this letter show the better characteristic of the phase noise and reduce the size of the VCO. The frequency tuning range of the VCO is about 200 ㎒ and the phase noise at 120 ㎑ offset is -119.3 ㏈c/㎐. The power consumption of the VCO core is 11.2 ㎽ at 2.8 V supply voltage and the output power is -2 ㏈m. The calculated figure of merit(FOM) is 191.7, which shows the best performance compared with the previous FET or HBT VCO.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.506-510
• /
• 2016

A triple-band (TB) oscillator was implemented in the TSMC $0.18{\mu}m$ 1P6M CMOS process, and it uses a cross-coupled nMOS pair and two shunt $4^{th}$ order LC resonators to form a $6^{th}$ order resonator with three resonant frequencies. The oscillator uses the varactors for band switching and frequency tuning. The core current and power consumption of the high (middle, low)- band core oscillator are 3.59(3.42, 3.4) mA and 2.4(2.29, 2.28) mW, respectively at the dc drain-source bias of 0.67V. The oscillator can generate differential signals in the frequency range of 8.04-8.68 GHz, 5.82-6.15 GHz, and 3.68-4.08 GHz. The die area of the triple-band oscillator is $0.835{\times}1.103mm^2$.

• Journal of electromagnetic engineering and science
• /
• v.6 no.1
• /
• pp.30-35
• /
• 2006

This paper describes fully integrated low phase noise MMIC voltage controlled oscillators(VCOs). The Asymmetrical Inductance Tank VCO(AIT-VCO), which optimize the shortcoming of the previous tank's inductance optimization approach, has lower phase noise performance due to achieving higher equivalent parallel resistance and Q value of the tank. This VCO features an output power signal in the range of - 11.53 dBm and a tuning range of 261 MHz or 15.2 % of its operating frequency. This VCO exhibits a phase noise of - 117.3 dBc/Hz at a frequency offset of 100 kHz from carrier. A phase noise reduction of 15 dB was achieved relative to only one spiral inductor. The AIT-VCO achieved low very low figure of merit of -184.6 dBc/Hz. The die area, including buffers and bond pads, is $0.9{\times}0.9mm^2$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.7
• /
• pp.1538-1543
• /
• 2013

In this paper, a novel split ring resonator is proposed for improvement of phase noise characteristics that is weak point of oscillator using planar type microstrip line resonator. Oscillator using proposed split ring resonator is designed, it has improved phase noise characteristics. At the fundamental frequency of 5.8GHz, 7.22dBm output power and -83.5 dBc@100kHz phase noise have been measured for oscillator with split ring resonator. The phase noise characteristics of oscillator is improved about 9.7dB compared to one using the general ${\lambda}/4$ microstrip resonator. Next, we designed voltage controlled oscillator using proposed split ring resonator with varactor diode. The VCO has 125MHz tuning range from 5.833GHz to 5.845GHz, and phase noise characteristic is -118~-115.5 dBc/Hz@100KHz. Due to its simple fabrication process and planar type, it is expected that the technique in this paper can be widely used for low phase noise oscillators for both MIC and MMIC applications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.1A
• /
• pp.134-141
• /
• 2007

This paper presents a frequency synthesizer(FS) for 5.2GHz/2.4GHz dual band wireless applications which is designed in a standard $0.18{\mu}m$ CMOS1P6M process. The 2.4GHz frequency is obtained from the 5.2GHz output frequency of Voltage Controlled Oscillator (VCO) by using the Switched Capacitor (SC) and the divider-by-2. Power dissipations of the proposed FS and VCO are 25mW and 3.6mW, respectively. The tuning range of VCO is 700MHz and the locking time is $4{\mu}s$. The simulated phase noise of PLL is -101.36dBc/Hz at 200kHz offset frequency from 5.0GHz with SCA circuit on.

• Journal of Power Electronics
• /
• v.13 no.4
• /
• pp.679-691
• /
• 2013

High-power electromagnetic transmitter power supplies are an important part of deep geophysical exploration equipment. This is especially true in complex environments, where the ability to produce a highly accurate and stable output and safety through redundancy have become the key issues in the design of high-power electromagnetic transmitter power supplies. To solve these issues, a high-frequency switching power cascade based emission power supply is designed. By combining the circuit averaged model and the equivalent controlled source method, a modular mathematical model is established with the on-state loss and transformer induction loss being taken into account. A triple-loop control including an inner current loop, an outer voltage loop and a load current forward feedback, and a digitalized voltage/current sharing control method are proposed for the realization of the rapid, stable and highly accurate output of the system. By using a new algorithm referred to as GAPSO, which integrates a genetic algorithm and a particle swarm algorithm, the parameters of the controller are tuned. A multi-module cascade helps to achieve system redundancy. A simulation analysis of the open-loop system proves the accuracy of the established system and provides a better reflection of the characteristics of the power supply. A parameter tuning simulation proves the effectiveness of the GAPSO algorithm. A closed-loop simulation of the system and field geological exploration experiments demonstrate the effectiveness of the control method. This ensures both the system's excellent stability and the output's accuracy. It also ensures the accuracy of the established mathematical model as well as its ability to meet the requirements of practical field deep exploration.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.9
• /
• pp.30-37
• /
• 2000

In this paper, design and fabrication of miniature voltage-controlled oscillator(VCO) is discussed . Based on the two-port circuit analysis technique, VCO for 900MHz cellular mobile phone is designed and circuit parameters are optimized using the circuit simulator. Using the optimized design parameters, miniature VCO with 6${\times}$6${\times}$1.8 mm$^3$(0.065cc) dimensions is fabricated and experimented. Experimental results show that implemented VCO has -3.5 dBm output power level and 45MHz tunung range, respectively, and has -101.5dB/Hz Phase noise performance at 10 KHz frequency offset.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.503-504
• /
• 2006

This paper presents the design and fabrication of a LC voltage-controlled oscillator (VCO) using 1-poly 6-metal mixed signal CMOS process. To obtain the high-quality factor inductor in LC resonator, patterned-ground shields (PGS) is placed under the symmetric inductor to reduce the effect from image current of resistive Si substrate. Moreover, due to the incapability of using thick top metal layer of which the thickness is over $2{\mu}m$, as used in many RF CMOS process, the structure of dual-metal layer in which we make electrically short circuit between the top metal and the next metal below it by a great number of via materials along the metal traces is adopted. The circuit operated from 2.63 GHz to 3.09 GHz tuned by accumulation-mode MOS varactor. The corresponding tuning range was 460 MHz. The measured phase noise was -115 dBc/Hz @ 1MHz offset at 2.63 GHz carrier frequency and the current consumption and the corresponding power consumption were about 2.6 mA and 4.68 mW respectively.