• Transactions on Electrical and Electronic Materials
• /
• v.18 no.5
• /
• pp.250-252
• /
• 2017

High-performance full swing logic inverters were fabricated using amorphous 1 wt% Si doped indium-zinc-oxide (a-SIZO) thin films with different channel layer thicknesses. In the inverter configuration, the threshold voltage was adjusted by varying the thickness of the channel layer. The depletion mode (D-mode) device used a TFT with a channel layer thickness of 60 nm as it exhibited the most negative threshold voltage (-1.67 V). Inverters using enhancement mode (E-mode) devices were fabricated using TFTs with channel layer thicknesses of 20 or 40 nm with excellent subthreshold slope (S.S). Both the inverters exhibited high voltage gain values of 30.74 and 28.56, respectively at $V_{DD}=15V$. It was confirmed that the voltage gain can be improved by increasing the S.S value.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.6
• /
• pp.891-896
• /
• 2002

In this paper, a new voltage-controlled tunable integrator for low-voltage applications is proposed. The proposed active element is composed of the CMOS complementary cascode circuit which can extend transconductance of an element. Therefore, the unity gain frequency which is determined transcon-ductance is increased than that of the conventional element. And then these results are verified by the $0.25{\mu}m$ CMOS n-well parameter HSPICE simulation. As a result, the gain and the unity gain frequency are 42dB and 200MHz respectively in the element on 2V supply voltage. And power dissipation of the designed circuit is 0.32mW.

• Journal of Power Electronics
• /
• v.7 no.1
• /
• pp.21-27
• /
• 2007

This paper investigates a PID fuzzy controller for output voltage regulation of a current-doubler-rectified asymmetric half-bridge (CDRAHB) DC/DC converter. The controller is a PD-type fuzzy controller in parallel with a linear integral controller. The PD type fuzzy controller is for providing the varying gain at the different operating conditions to regulate the output voltage. The linear integral controller is for removing the steady-state error of the output voltage. In order to show the outstanding dynamic characteristics of the proposed controller, PSIM simulation studies are carried out and compared to the results for which the conventional loop gain design method is used.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.7
• /
• pp.1195-1199
• /
• 2008

In this paper, peak detector of generator's output voltage and variable gain controller are introduced for a fast dynamic response. The conventional r,m.s, signal detected has inherent time delay, and the dynamic response of generator using conventional PID controller has some problem in sudden load change. In this paper, the peak detector and signal selector with variable gain controller is used to overcome this problem. The main controller can check the voltage state from the peak detector. When a sudden load change, the over-voltage and under-voltage signal from peak detector change the controller's gain and exciter's current reference. The proposed scheme can improve the dynamic response, which is verified from experimental test of 200kW diesel engine-generator.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.672-680
• /
• 2018

A bidirectional exponential-gain switched-capacitor (SC) DC-DC converter is developed in this paper. When compared with existing exponential SC converters, the number of switches is significantly reduced and its structure is simplified. The voltage transfer features, voltage ripple across capacitors, efficiency and output impedance of the proposed converter are analyzed in detail. Optimization of the output impedance is also discussed and the best type of capacitance distribution is determined. A common function of the voltage gain to the output impedance is found among the proposed converter and other popular SC voltage multipliers. Experimental evaluation is carried out with a 6-24V bidirectional prototype converter.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.3
• /
• pp.1235-1244
• /
• 2017

This paper proposes a fuzzy logic controlled new topology of high voltage gain zero voltage switching (ZVS) asymmetrical PWM full-bridge DC-DC boost converter for constant load and high power applications. The APWM full-bridge stage provides high voltage gain and soft-switching characteristics increase the efficiency and reduce the switching losses. Fuzzy logic controller (FLC) improves the performance and dynamic characteristics of the proposed converter. A comparison with a classical proportional-integral (PI) controller demonstrates the high performances of the proposed technique in terms of effective output voltage regulation under different operating conditions. Simulation is done by integrating two different simulation platforms $PSIM^{(R)}$ and $Matlab^{(R)}/Simulink^{(R)}$ by using SimCoupler tool of $PSIM^{(R)}$. Experimental results using 120W load have been provided to validate the results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.2
• /
• pp.142-151
• /
• 2020

This paper presents a DC/DC LLC resonant converter with wide input/output voltage gain characteristics and its control method for efficiency improvement. For a wide input/output voltage gain characteristics without designing small transformer magnetization inductance, the proposed converter changes the topology into three modes of operation according to the main switch switching pattern. In each operating mode, variable LINK voltage modulation and frequency modulation were performed to control output voltage and improve operating efficiency. A prototype of a 5-kW DC/DC LLC resonant converter was built and tested to verify the validity and applicability of the proposed converter.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.10
• /
• pp.61-66
• /
• 2007

A gain enhancement rail-to-rail buffer amplifier for liquid crystal display (LCD) source driver is proposed. An op-amp with extremely high gain is needed to decrease the offset voltage of the buffer amplifier. Cascoded floating current source and class-AB control block in the op-amp achieve a high voltage gain by reducing the channel length modulation effect in high voltage technologies. HSPICE simulation in $1\;{\mu}V$ 15 V CMOS process demonstrates that voltage gain is increased by 30 dB. The offset voltage is improved from 6.84 mV to $400\;{\mu}V$. Proposed op-amp is fabricated in an LCD source driver IC and overall system offset voltage is decreased by 2 mV.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.12-16
• /
• 2003

This paper presents a compensation method for a temperature-dependent gain tilt in L-band erbium-doped fiber amplifier using a voltage-controlled attenuator. The gain tilts in the L-band of 1570-1605 nm due to a temperature change have negative slopes, whereas they have positive slopes for the increasing optical input powers in a saturation region. The proposed method utilizes these opposite gain variations to compensate for the gain tilt over a wide range of temperature. While applying forty channels with a channel spacing of 100 GHz in the L-band and changing the ambient temperature from 0 to $50^{\circ}C$, the compensation method maintained the gain deviation within 1 dB.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.3
• /
• pp.225-230
• /
• 2018

This paper proposes a parametric design of an LLC resonant inverter used for a microwave oven. To improve the harmonic performance of the microwave oven, a current controller with a variable PI gain is proposed. Due to the recent strengthening of harmonics regulations, inverter control technology for microwave ovens is now required to satisfy harmonic performance. In an LLC resonant inverter, the voltage gain varies remarkably depending on the magnetron voltage, output power, and input voltage. To satisfy harmonic performance, a controller that can maintain operation in the zero-voltage switching (ZVS) region and control changes in voltage gain is required. The modified design of the LLC resonant inverter ensures ZVS operation even when the magnetron is heated. Application of the variable current controller improves harmonic control according to the instantaneous gain curve change. The validity of the proposed power control with a variable current controller is verified by experiments with a 1200 W microwave oven.