• Korean Journal of Metals and Materials
• /
• v.50 no.2
• /
• pp.159-163
• /
• 2012

A TCO-less ruthenium (Ru) catalytic layer on glass substrate instead of conventional Ru/TCO/ glass substrate was assessed as counter electrode (CE) material in dye sensitized solar cells (DSSCs) by examining the effect of the Ru thickness on the DSSC performance. Ru films with different thicknesses (34, 46, 69, and 90 nm) were deposited by atomic layer deposition (ALD) on glass substrates to replace both existing catalyst and electrode layer. In order to make our comparison, we also prepared an Ru catalytic layer by a similar method on FTO/glass substrate. Finally, we prepared the $0.45cm^2$ DSSC device the properties of the DSSCs were examined by cyclic voltammetry (CV), impedance spectroscopy (EIS), and current-voltage (I-V) method. CV measurements revealed an increase in catalytic activity with increasing film thickness. The charge transfer resistance at the interface between the electrolyte and Rudecreased with increasing Ru thickness. I-V results showed that the energy conversion efficiency increased up to 1.96%. Our results imply that TCO-less Ru/glass might perform as both catalyst and electrode layer when it is used in counter electrodes in DSSCs.

• Korean Journal of Optics and Photonics
• /
• v.31 no.1
• /
• pp.37-44
• /
• 2020

In this study, we propose a design method to optimize the electro-optical efficiency of a planar solar cell structure by adjusting one-dimensionally periodic emitter electrodes. Since the aperture ratio of the active layer decreases as the period of the emitter electrode decreases, the amount of light absorption diminishes, affecting the performance of the device. Here we design the optimal structure of the periodic emitter electrode in a simple planar solar cell, by simulation. In terms of optics, we find the condition that shows optical performance similar to that of a reference without the emitter electrode. In addition, the optimized electrode structure is extracted considering both the optical and electrical efficiency. This work will help to increase the utilization of solar cells by suggesting a structure that can most efficiently transfer charge generated by photoelectric conversion to the electrodes.

• Journal of Adhesion and Interface
• /
• v.22 no.4
• /
• pp.153-157
• /
• 2021

Graphene, a two-dimensional carbon allotrope, has outstanding mechanical and electrical properties. In particular, the charge carrier mobility of graphene is known to be about 100 times higher than that of silicon, and it has received attention as a core material for next-generation electronic devices. However, graphene is very sensitive to environmental conditions, especially vulnerable to moisture or oxygen. It becomes a disadvantage in that the stability of the graphene-based electronic device, so various attempts are being made to solve this problem. In this work, we report a method to greatly improve the stability by controlling the surface energy of the polymer layer used for transferring the insulating layer of the graphene field-effect transistor. As the surface energy of the polymer used as the insulating layer was lowered, the stability could be improved by effectively controlling the adsorption of impurities in the atmosphere such as water molecules or oxygen.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.290-296
• /
• 2019

Head-up displays for vehicles play an important role in displaying various information about the safety and convenience of driving on the windshield of the vehicle. In this study, ultra-precision machining was performed and evaluated as a method for machining a large-area aspheric free-form mirror that is applicable to augmented reality technology. Precision diamond cutting is highly accurate and suitable for the production of advanced parts with excellent surface integrity, low surface roughness, and low residual stress. By using an aspheric free-form mold, it is possible to improve the optical transfer function, reduce the distortion path, and realize a special image field curvature. To make such a mold, the diamond cutting method was used, and the result was evaluated using an aspherical shape-measuring machine. As a result, it was possible to the mold with shape accuracy (PV) below $1{\mu}m$ and surface roughness (Ra) below $0.02{\mu}m$.

• Journal of Convergence for Information Technology
• /
• v.11 no.2
• /
• pp.90-97
• /
• 2021

In this study, a Bi2Te3 thermoelectric generator (TEG) was fabricated to convert unused thermal energy into useful electrical energy. For the performance test, a dedicated experiment device consisting of a heating block operating with cartridge heaters and a cooling block through which a refrigerant flows was constructed. A 3×3 array of thermocouples was mounted on the heating block and the cooling block, respectively, to derive the temperature fields and heat transfer rate onto both sides of the TEG. Experiments were conducted for a total of 9 temperature differences, obtaining V-I and P-R curves. The results of 7 variables including Seebeck coefficients that have a major effect on performance were presented as a function of the temperature difference. The feasibility of the energy recovery performance of the developed TEG was verified from the maximum power output of 7.5W and conversion efficiency of 11.3%.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.21 no.4
• /
• pp.125-136
• /
• 2011

The vulnerabilities existed in Korean electricity control systems is unexposed because it is being operated in a closed network with superior security. The threat will become greater once the closed network develops into a smart grid environment with superior intelligence. Security will have a greater impact once each household will be connected to the power plant via the smart meter. This research focuses on stable data transfer in harsh external environment and whole-nation coverage network, and suggested standardized and optimized Virtual Private Network (VPN) Gateway architecture to support Power Line Communication (PLC). The functionality and stability of the prototype has been verified with field tests. For implementation of outdoor type VPN device for smart grid, we adopted PLC low voltage remote-meter-net for data communication. Also, IPSec type tunneling and ARIA algorithm based encryption of data collected by PLC low voltage remote meter is transmitted.

• Journal of the Korean Society of Safety
• /
• v.35 no.6
• /
• pp.32-45
• /
• 2020

The problem of determining the discharge rates of gases from pressurized vessels through pressure relief devices was dealt with comprehensively. First, starting from basic fluid flow equations, detailed modeling procedures were presented for isentropic nozzle flows and frictional flows in a pipe, respectively. Meanwhile, physical explanations were given to choking phenomena in terms of the acoustic velocity, elucidating the widespread use of Mach numbers in gas flow models. Frictional flows in a pipe were classified into adiabatic, isothermal, and general flows according to the heat transfer situation around the pipe, but the adiabatic flow model was recommended suitable for gas discharge through pressure relief devices. Next, for the isentropic nozzle flow followed by adiabatic frictional flow in the pipe, two equations were established for two unknowns that consist of the Mach numbers at the inlet and outlet of the pipe, respectively. The relationship among the ratio of downstream reservoir pressure to upstream pressure, mass flux, and total frictional loss coefficient was shown in various forms of MATLAB 2-D plot, 3-D surface plot and contour plot. Then, the profiles of gas properties and velocity in the pipe section were traced. A method to quantify the relationship among the pressure head, velocity head, and total friction loss was presented, and was used in inferring that the rapid increase in gas velocity in the region approaching the choked flow at the pipe outlet is attributed to the conversion of internal energy to kinetic energy. Finally, the Levenspiel chart reproduced in this work was compared with the Lapple chart used in API 521 Standatd.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.12
• /
• pp.173-186
• /
• 2020

In this paper, we design and implement a service system for mobile devices to utilize the integrated underground geospatial information map in underground exploration fields. The field utilization service system for mobile devices is designed to visualize tiled maps, 3D terrain information, underground structures, underground facilities, and ground information provided by the Integrated Underground Geospatial Information Map Management System according to current position. And It is designed to reflect the results obtained from field exploration in real time. Also, the proposed system is implemented to transfer and visualize the integrated underground geospatial information map in the form of a glTF format due to constraints on wireless networks and device characteristics of mobile devices. Implemented mobile service systems can prevent accidents in underground exploration field from occurring by providing users with accurate and integrated underground geospatial data by visualizing maps and geospatial objects in three dimensions at underground exploration fields. In addition, updated underground geospatial data is transmitted in real time to the Integrated Underground Geospatial Information Map Management Systems, which can maintain up to date and accuracy.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.10
• /
• pp.1188-1194
• /
• 2019

Among the many ways to measure the flow of fluid the hot air wind speed sensor is a device for measuring the speed or temperature by heat transfer of a fluid. However, the hot wire wind speed sensor is sensitive to external environmental factors, and has a disadvantage of inaccuracy due to ambient temperature, humidity, and signal noise. In order to compensate for this disadvantage, advanced technology has been introduced by adding temperature compensation circuits, but it is expensive. In order to solve this problem, this paper studies the wind speed sensor that does not need temperature compensation. Heated wind speed sensors are very vulnerable to the ambient temperature, which is generated by electronic circuits, even among external environmental factors. in order to improve this, the auxiliary heating element is additionally installed in the heating element to control a constant temperature difference between the auxiliary heating element and the heating element.

• Parasites, Hosts and Diseases
• /
• v.59 no.1
• /
• pp.77-82
• /
• 2021

As malaria remains a major health problem worldwide, various diagnostic tests have been developed, including microscopy-based and rapid diagnostic tests. LabChip real-time PCR (LRP) is a small and portable device used to diagnose malaria using lab-on-a-chip technology. This study aimed to evaluate the diagnostic performance of LRP for detecting malaria parasites. Two hundred thirteen patients and 150 healthy individuals were enrolled from May 2009 to October 2015. A diagnostic detectability of LRP for malaria parasites was compared to that of conventional RT-PCR. Sensitivity of LRP for Plasmodium vivax, P. falciparum, P. malariae, and P. ovale was 95.5%, 96.0%, 100%, and 100%, respectively. Specificity of LRP for P. vivax, P. falciparum, P. malariae, and P. ovale was 100%, 99.3%, 100%, and 100%, respectively. Cohen's Kappa coefficients between LRP and CFX96 for detecting P. vivax, P. falciparum, P. malariae, and P. ovale were 0.96, 0.98, 1.00, and 1.00, respectively. Significant difference was not observed between the results of LRP and conventional RT-PCR and microscopic examination. A time required to amplify DNAs using LRP and conventional RT-PCR was 27 min and 86 min, respectively. LRP amplified DNAs 2 times more fast than conventional RT-PCR due to the faster heat transfer. Therefore, LRP could be employed as a useful tool for detecting malaria parasites in clinical laboratories.