• 한국유체기계학회 논문집
• /
• 제16권6호
• /
• pp.19-25
• /
• 2013

The effect of tip gap height on heat/mass transfer characteristics on the floor of cavity squealer tip has been investigated in a turbine cascade for power generation by employing the naphthalene sublimation technique. The squealer rim height is chosen to be an optimal one of $h_{st}/c$ = 5.51% for the tip gap height-to-chord ratios of h/c = 1.0, 2.0, 3.0 and 4.0%. The results show that heat transfer on the cavity floor is strongly dependent upon the behavior of the cavity flow falling down onto the floor. For lower h/c, the floor heat transfer is influenced by the tip leakage flow falling down along the inner face of the suction-side squealer, whereas the floor heat transfer for higher h/c is augmented mainly due to the impingement of leakage flow on the floor near the leading edge. Compared to the plane tip surface heat transfer, the cavity floor heat transfer is less influenced by h/c. For h/c = 1.0%, the average thermal load is as low as a half of the plane tip surface one, and the difference in the thermal load between the two cases tends to decrease with increasing h/c.

• 한국안전학회지
• /
• 제20권2호
• /
• pp.79-83
• /
• 2005

Recently, column-supported wall structural system is frequently adopted in mixed-use high-rise buildings. Due to the sudden change of stiffness at the transfer floor proper load transfer and avoiding stress concentration are very important in column-supported wall structural system. It is revealed by many investigators that 2-dimensional analysis is not reliable and inappropriate selection of element for modeling may lead to erroneous result for gravitational loading. In this study, structural behavior of column-supported wall structure at transfer floor subject to lateral loading is compared by changing modeling methods.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제12권2호
• /
• pp.97-107
• /
• 2004

Wall/floor intersection is important parts of a building envelope system. These intersections can be sources of thermal bridging effects and/or moisture condensation problems. This paper provides a detailed analysis of the thermal performance of wall/floor intersection. In particular, two-dimensional steady-state and transient solutions of the heat conduction within the wall/floor joint are presented. Various insulation configurations are considered to determine the magnitude of heat transfer increase due to wall/floor joint construction.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.175-181
• /
• 2006

The prediction of time-dependent column shortening is essential for tall buildings considering both strength and serviceability aspects. The Column shortening of tall buildings with transfer floor should be calculated considering the long-term deflection of transfer girder. In this study, both the column shortening and the deflection of transfer girder of 45-story tall concrete building are predicted. The column shortening considering deflection of transfer girder are compared with the actual column shortening by field measurement.

• 한국기계가공학회지
• /
• 제21권2호
• /
• pp.94-100
• /
• 2022

A study was conducted to significantly increase the heat transfer area by simultaneously burying the excel pipe in the floor and wall of a container house, thereby greatly reducing the initial heating time. In addition, a small hot water boiler suitable for the heating load of a small container house with a maximum area of 6 m² was studied. A wall-mounted hot water boiler was developed as a result of the study. When a hot water boiler is installed outdoors for heating, heat radiation energy is lost in winter from the hot water boiler and hot water pipe due to the low temperature. We propose an approach through which the energy loss was greatly reduced and the temperature of hot water increased in proportion to the operating time. Moreover, as the mass flow rate of the hot water flowing inside the excel pipe increased, the temperature of the hot water decreased. The temperature of the wall and floor surfaces of the container house increased in proportion to the increase in the mass flow rate of hot water flowing inside the excel tube. Natural convection heat transfer was realized from the wall and floor surfaces of the container house, and the heat transfer area was increased by a factor of 3 with respect to heat transfer area limited to the floor by the existing hot water panel. As a result, the initial temperature increase rate was much higher because of the larger heat transfer area.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.225-226
• /
• 2014

In multi-story buildings, heavy-weight floor impact noise propagates through multiple layers. In order to evaluate the influence of structural vibration and propagation, the actual twelve-story building was excited by an impact ball. Sound and vibration responses of each floor was measured using accelerometers and a microphone. Vibration characteristics and its transfer paths were different depending on the excitation floor locations due to differences in the structural characteristics. From the measurement result, transfer characteristics were quantified by statistical energy analysis. It was confirmed that the heavy-weight floor impact noise influence not only adjacent floor. The impact noise transferred and affected multiple layers.

• 한국건설관리학회논문집
• /
• 제15권6호
• /
• pp.53-62
• /
• 2014

최근 세계 경제가 금융위기로부터 회복되기 시작하면서 전 세계적으로 초고층 건축공사 프로젝트가 증가하는 추세에 있다. 수직 리프트 양중은 리프트 양중 장비 대수의 제약으로 인해 초고층 건축공사 프로젝트에 있어서 전체 프로젝트의 생산성 측면에서 매우 중요한 요소이다. 특히 건물 높이가 400m 이상 되는 초고층 건축공사에서는, 리프트의 최대 운행높이로 인해 환승운영방식의 리프트 양중이 필수적이다. 환승운영방식 리프트 양중에서의 환승층 지정은 자원들의 양중 시간 단축에 많은 영향을 미친다. 본 연구에서는 AnyLogic 프로그램을 통한 이산사건 시뮬레이션 모델 구축 및 OptQuest 최적화 프로그램을 통한 메타휴리스틱 방식의 최적해 탐색으로 오전 출근시간대의 작업원 양중 시 환승층 최적화를 위한 방법을 제안하였다. 중간층을 환승층으로 지정했을 때와 비교한 결과, 최적 환승층을 지정했을 때 작업자들의 전체 양중시간이 상당히 단축되는 것으로 분석되었다. 본 연구에서 제안하는 도구를 사용 시 초고층 건축공사 프로젝트에서 작업원들의 가용 작업시간 증가를 통한 비용 절감 및 프로젝트 공기 단축이 가능할 것으로 예상된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.441-446
• /
• 2008

The source transfer receiver model ('Source $\times$ Transfer = Response' model) which is widely used by NVH development process of vehicle/transport/machinery to analyze effectively and manage efficiently the structural dynamic behavior is also applicable to construction structure. If the evaluation assessment of the vibration level does not meet the target level, there are two methods, one is source treatment or replacement and the other is the reduction treatment on the transfer structure. In case of source treatment, it is done by source supplier and so, the latter is more practical method to reduce the vibration level. In this study, in order to get the accurate Transfer FE model(floor structure FE model), Experimental modal analysis of part of floor structure and FEM modal analysis of full floor structure are performed, then updating of FE model is performed after correlation analysis between these two results and finally, the modal model and FRF are compared between FE and Experimental results.

• 설비공학논문집
• /
• 제17권12호
• /
• pp.1123-1131
• /
• 2005

The floor material is known as the most influential emission source of the residential building, because most floor material is made of wood compound and adhesive like a plywood flooring. Moreover, floor heating system keeps the inside temperature of the material high. As the emission of hazardous chemical compound from the construction material is influenced by many factors, it is necessary to analyze the emission characteristics of the floor material to improve IAQ. In this study, numerical analysis is performed to investigate the emission characteristics of the floor material affected by several factors such as temperature, air exchange rate, initial concentration, and internal diffusion coefficient. A simulation program is also written based on the mass transfer theory. The simulation results show that there is some level of difference on the TVOC concentration when each of the factors is variable.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.510-513
• /
• 2006

Due to the location of vibration sensitive equipment on the floor, it is necessary for its vibration performance to be maintained within stringent limits, resulting in a design of higher mass and stiffness than would be usual for a floor of this type. Modal testing is conducted on the floor to obtain their dynamic characteristics. A considerable level of vibration transmission is observed by comparing the ratio of simulated transfer and point mobility FRFs of the floor.