• 한국광학회지
• /
• 제9권2호
• /
• pp.111-116
• /
• 1998

활성층의 변형이 0.9%의 압축변형에서 1.4%의 인장변형에 이르는 13개의 InGaAs/InGaAsP 따로가둠 이종접합 다중양자우물 레이저의 문턱전류밀도 값을 계산하여, 변형이 문턱전류밀도에 미치는 영향을 살펴보았다. 양자우물의 띠간격이 1.55.mu.m가 되도록 양자우물의 두께를 정하였고, 레이저의 이득계산을 위한 띠구조 및 전이행렬요소의 계산에는 블록대각화된 8 * 8 이차 $k^{\rarw}$ * $p^{\rarw}$ 해밀토니안을 사용하여 전도띠의 비포물선형 효과 및 원자가띠의 섞임을 모두 고려하였다. 실온의 문턴전류밀도는 중양공띠와 경양공띠가 교차하는 0.4% 인장변형의 값과 두번째 전도부띠가 생기기 시작하는 0.5% 인장변형의 값에서 불연속점을 가졌다. 실온의 문턱전류밀도는 이 0.4-0.5% 인장변형 부근에서 극대가 되고, 양쪽으로 변형값이 달라지면서 감소하였다가 극소점을 거쳐 다시 약간 증가하는 모습을 보였는데, 이는 실험결과와 대체로 일치한다. 이 계산결과를 변형의 효과에 관한 다른 여러 이론적 혹은 실험적인 논문들과 비교 토론하였다.

• 한국방재학회 논문집
• /
• 제10권3호
• /
• pp.39-43
• /
• 2010

본 연구의 주목적은 아스팔트 혼합물의 피로균열에 대한 예측모델을 개발하는 것이다. 아스팔트 혼합물의 피로균열 시험을 위하여 응력제어 간접인장피로 시험이 수행되었다. 피로균열에 대한 예측모델 개발을 위하여 내적손상비 증가 개념이 도입되었다. 내적손상비증가 개념에서는 방출에너지 개념을 주로 사용하였으며 기준인장변형율 및 변형율 추이 요소 등이 추가로 사용되었다. 피로시험에서 나타난 방출에너지의 원인은 아스팔트 콘크리트 시료 내부의 손상증가와 재료 자체가 갖고 있는 고유의 점탄성 특성에 기인하는 것으로 판단된다. 방출에너지는 하중재하 횟수가 증가함에 따라 점차 증가함을 보였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.439-442
• /
• 2006

We evaluated a-Si:H TFTs fabricated on polyimide substrate (PI) at the highest temperature of $160^{\circ}C$ with uniaxial and tensile strain to imitate flexible display. With tensile strain, the threshold voltage of a-Si:H TFTs have positive shift due to extra dangling bond formation in a-Si:H layer. However, no significant degradation of the subthreshold swing and effective mobility with tensile strain of a-Si:H TFTs indicates the similar level of band tail state. The metal wire with the width of $10\;{\mu}m$ for connection on flexible substrate can sustain with curvature radius 2.5 cm.

• Composites Research
• /
• 제17권5호
• /
• pp.61-67
• /
• 2004

본 연구에서는 전자파 차폐용 도전성 개스킷 소재로 활용할 수 있는 은입자 충전 실리콘 복합 페이스트에 대한 전기전도성 및 응력-변형율 특성을 분석하였다. 불규칙한 구형의 은(Ag)입자와 상온습기경화형(RTV) 실리콘수지를 도입하여 복합 페이스트의 퍼콜레이션 농도(임계 농도)를 전기전도도 측정 결과로부터 결정하였다. 약 28%의 은입자 함량에서 퍼콜레이션 현상이 발생하였으며, 이 농도에서 급격한 감소를 보이는 은입자/실리콘 복합 페이스트의 체적 비저항, 인장강도 및 연신률의 특성 변화에 관하여 고찰하였다. 또한, 커플링제의 선택적 방법을 통해 퍼콜레이션 농도 이상으로 충전된 복합 페이스트의 응력-변형율 특성을 효과적으로 개선할 수 있음을 제시하여 주었다.

• 전기전자학회논문지
• /
• 제20권3호
• /
• pp.330-332
• /
• 2016

본 연구에서는 8와 $100{\mu}m$의 채널 길이를 가지는 밴더블 a-Si:H 박막 트랜지스터를 제작하고, 밴딩 스트레인에 따른 전기적 특성변화를 측정하였다. 1.69%의 밴딩 스트레인에서 $8{\mu}m$ 채널 길이를 가지는 박막트랜지스터는 문턱 전압이 5.25 V까지 이동하였으나 $100{\mu}m$ 채널 길이를 가지는 박막트랜지스터는 전기적 특성 변화 없이 안정적으로 동작하였다.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제6권2호
• /
• pp.135-150
• /
• 2006

Rubber material properties and lifetime evaluation are very important in design procedure to assure the safety and reliability of the rubber components. This paper discusses the failure mechanism and material tests were carried out to predict the useful lifetime of NBR and EPDM for compression motor, which is used in refrigerator component. The heat-aging process leads not only to mechanical properties change but also to chemical structure change so called degradation. In order to investigate the aging effects on the material properties, the accelerated test were carried out. The stress-strain curves were plotted from the results of the tensile test for virgin and heat-aged rubber specimens. The rubber specimens were heat-aged in an oven at the temperature ranging from $70^{\circ}C\;to\;100^{\circ}C$ for a period ranging from 1 to 180 days. Compression set results changes as the threshold are used for assessment of the useful life and time to threshold value were plotted against reciprocal of absolute temperature to give the Arrhenius plot. By using the compression set test, several useful lifetime prediction equations for rubber material were proposed.

• 대한조선학회논문집
• /
• 제45권5호
• /
• pp.530-537
• /
• 2008

Austenitic stainless steels(SUS 304, SUS 316), which are used for safety control valve of LNG carrier, are occasionally exposed in the cryogenic environment. In this regards, it is required to evaluate the mechanical characteristics under the low temperature environment. In this study, a series of uniaxial tensile test was carried out varying temperature for austenitic stainless steel. The phenomena of the strain-induced plasticity have been observed on the all temperature ranges. The critical value for threshold of 2nd hardening due to the phase transformation induced plasticity as well as the increase of hardening have been reported. The summarized experimental results would be used for the validation of numerical techniques applicable for the nonlinear hardening behavior of austenitic stainless steel under the cryogenic temperature environment.

• 전자공학회논문지A
• /
• 제32A권6호
• /
• pp.75-81
• /
• 1995

InGaAsP/InP uncooled LDs emitting at 1.3$\mu$m wavelength are of interest for several application of fiber-to-the-home, optical interconnection, long-haul high-bit-rate optical transmission systems, etc. The strain compensated PBH-MQW-LD employing 1.4% compressive strained well (${\lambda}=1.3{\mu}m$) and 0.7% tensile strained barrier (${\lambda}=1.12{\mu}m$) layers grown by low pressure metallicorganic vapor phase epitaxy was found to be low threshold current and stable temperature characteristics. The average threshold current of 5.6mA and average slope efficiency of 0.27mW/mA at room temperature were obtained for uncoated uncooled-LD.

• 전자공학회논문지A
• /
• 제33A권7호
• /
• pp.185-197
• /
• 1996

We have adopted the strain compensated PBH(planar buried heterostructure) - LD in which the MQW active layer consisted of 1.4% compressively strained GainAsP (E$_{g}$ = 0.905eV) wells and 0.7% tensile strained GaInAsP(E$_{g}$ = 1.107eV) barriers grown by metal organic vapor phase epitaxy (MOVPE). We hav einvestigated effects of number of wells and the structure of the separate confinement heterostructure (SCH) layer in the strain-compensated MQW-PBH-LD. The threshold current, the external quantum efficiency, the transparency current density J$_{o}$, and the gain constant .beta. have been evaluated for uncoated MQW-PBH-LD. As the number of wells increases, the internal quantum efficiency and the transparency current density decreases, whereas the gain contant increases. The small width of the SCH layer shows the large internal quantum efficiency. The small internal loss and the large gain constant have been obtained by inserting the large bandgap SCH layer.

• International Journal of Concrete Structures and Materials
• /
• 제11권2호
• /
• pp.343-363
• /
• 2017

The objective of this work was finding out the most advisable testing conditions for an effective and robust characterization of the tensile strength (TS) of concrete disks. The independent variables were the loading geometry, the angle subtended by the contact area, disk diameter and thickness, maximum aggregate size, and the sample compression strength (CS). The effect of the independent variables was studied in a three groups of experiments using a factorial design with two levels and four factors. The likeliest location where failure beginning was calculated using the equations that account for the stress-strain field developed within the disk. The theoretical outcome shows that for failure beginning at the geometric center of the sample, it is necessary for the contact angle in the loading setup to be larger than or equal to a threshold value. Nevertheless, the measured indirect tensile strength must be adjusted to get a close estimate of the uniaxial TS of the material. The correction depends on the loading geometry, and we got their mathematical expression and cross-validated them with the reported in the literature. The experimental results show that a loading geometry with a curved contact area, uniform load distribution over the contact area, loads projected parallel to one another within the disk, and a contact angle bigger of $12^{\circ}$ is the most advisable and robust setup for implementation of BT on concrete disks. This work provides a description of the BT carries on concrete disks and put forward a characterization technique to study costly samples of cement based material that have been enabled to display new and improved properties with nanomaterials.