• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.2
• /
• pp.489-494
• /
• 2006

The strain distribution in the vicinity of a hole in a tensile strip was measured using an image correlation method. The objective of this study is to evaluate the capability of predicting the strain component response using a constitutive model that was developed for use with paper materials. The need for a special constitutive model for paper derives from the characteristics of pronounced anisotropy and the fact that the material behaves differently under compressive loading than it does under tensile loading. The results of the simulation showed that predictions of strain distribution around the hole were in agreement with the experimental result trends, however, the agreement deteriorated as the edge of the hole was reached. It was observed that there is extensive inelastic strain that takes place around the hole prior to failure of the tensile strip. The simulation results showed that any difference between tensile and compressive behavior that may exist for paper material does not have any significant effect for the problem of this study because the level of compressive stress is quite low in comparison with compressive failure values.

• 한국분말재료학회지
• /
• 제28권4호
• /
• pp.301-309
• /
• 2021

In this study, an AISI 316 L alloy was manufactured using a selective laser melting (SLM) process. The tensile and impact toughness properties of the SLM AISI 316 L alloy were examined. In addition, stress relieving heat treatment (650℃ / 2 h) was performed on the as-built SLM alloy to investigate the effects of heat treatment on the mechanical properties. In the as-built SLM AISI 316 L alloy, cellular dendrite and molten pool structures were observed. Although the molten pool did not disappear following heat treatment, EBSD KAM analytical results confirmed that the fractions of the low- and high-angle boundaries decreased and increased, respectively. As the heat treatment was performed, the yield strength decreased, but the tensile strength and elongation increased only slightly. Impact toughness results revealed that the impact energy increased by 33.5% when heat treatment was applied. The deformation behavior of the SLM AISI 316 L alloy was also examined in relation to the microstructure through analyses of the tensile and impact fracture surfaces.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.401-407
• /
• 2004

This study is on the constant-current stress corrosion test related to the load stress in welded zone and non-welded zone of high tensile strength steel for natural gas transmission. The surface corrosion pattern of the welded zone of API 5L-X65 specimens for natural gas transmission showed global corrosion and narrow pitting, and the pitting was increased by increasing the load stress. Initially, the average relative electrode potential and the average relative current of the high tensile strength steel for natural gas transmission specimens was decreased suddenly, and the average relative electrode potential was higher and the average relative current was lower in welded zone than base metal. and the average relative electrode potential was decreased by increasing the load stress, and the average relative current was somewhat increased by increasing the load stress. The corrosion rate was less in welded zone than base metal, and the corrosion rate was decreased by increasing the load stress.

• Structural Engineering and Mechanics
• /
• 제14권4호
• /
• pp.455-472
• /
• 2002

The paper involves the study on the elastic and elasto-plastic stress wave propagation in the 1-D and 2-D solid media. The Smooth Particle Hydrodynamics equations governing the elastic and elasto-plastic large deformation dynamic response of solid structures are presented. The proposed additional stress points are introduced in the formulation to mitigate the tensile instability inherent in the SPH approach. Both incremental rate approach and leap-frog algorithm for time integration are introduced and the new solution algorithm is developed and implemented. Two examples on stress wave propagation in aluminium bar and 2-D elasto-plastic steel plate are included. Results from the proposed SPH approach are compared with available analytical values and finite element solutions. The comparison illustrates that the stress wave propagation problems can be effectively solved by the proposed SPH method. The study shows that the SPH simulation is a reliable and robust tool and can be used with confidence to treat transient dynamics such as linear and non-linear transient stress wave propagation problems.

• 대한기계학회논문집
• /
• 제8권2호
• /
• pp.127-132
• /
• 1984

본 연구에서는 상술한 점들을 고려하고 우선 다음과 같은 사항을 고찰하려고 노력하였다. 즉 슬롯 및 노치주위에는 어떤 응력들이 분포되며 응력분포거동은 어떤 인자에 의하여 좌우되는가, 어떤 응력이 응력집중을 지배하며 응력집중현상은 어떤 인 자에 의하여 좌우되는가를 주로 고찰하였다. 참고로 실험에서 노치 및 슬롯선단의 응력측정에는 실제로 기계나 구조물에 직접 사용할 수 있는 스트레인 게이지를 사용하 였고 측정치의 정도를 높이기 위하여 스트레인 게이지율 교정방법을 이용하였다. 참 고로 노치 및 슬롯주위에 발생하는 응력집중과 파괴거동과의 관계에 대해서는 다음에 보고하겠다.

• 대한토목학회논문집
• /
• 제40권2호
• /
• pp.183-189
• /
• 2020

이 논문은 인장 응력, 주변 온도 및 인가 주파수에 대한 강선의 전기적 임피던스 민감도에 관한 실험적 조사이다. 다양한 응력 수준 및 온도에 대해서, 강선의 전기적 임피던스가 자가진단 시스템에서 측정되었다. 세 가지 경우의 실험이 다양한 온도 조건, 응력 수준 및 적용 주파수에 대해서 수행되었다. 주어진 주파수에서 온도가 상승하고 응력이 감소하면 강선의 전기 임피던스가 증가한다. 실험 결과는 전기적 임피던스와 온도 사이의 상관관계가 모든 응력 수준에서 선형 관계임을 보여준다. 온도에 대한 임피던스의 감도는 응력보다 훨씬 높다는 점이 주목 된다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권9호
• /
• pp.665-671
• /
• 1999

The paper represents the effects of the drive-in process parameters on the residual stress profile of the $p^+$ silicon film. Since the residual stress profile is notuniform along the direction normal to the surface, the residual stress is assumed to be a polynomial function of the depth. All the coefficients of the polynomial can be determined by measuring of the thicknesses and the deflections of cantilevers and the deflection of a rotating beam with a surface profiler meter and a microscope. As the drive-in temperature or the drive-in time increases, the boron concentration decreases and the magnitude of the average residual tensile stress decreases. Then, near the surface of the $p^+$ film the residual tensile stress is transformed into the residual compressive stress and its magnitude increases.

• Elastomers and Composites
• /
• 제45권4호
• /
• pp.250-255
• /
• 2010

비뉴톤 점탄성 Maxwell 요소와 탄성 스프링으로 이루어진 3 요소 비뉴톤 모델로부터 응력완화 식을 유도하였다. 이 식을 응력완화 실험 결과에 적용하여 여러 가지 모델 파라메타를 계산하였다. 모델 파라메타로부터 계산한 이론 곡선은 실험적인 응력완화 곡선과 잘 일치하였다. 비선형 점탄성 모델 파라메타로부터 섬유고분자 물질의 홀부피, 미세구조, 점탄성성질, 역학적인 성질 등을 연구하였다. 응력완화 실험은 용매기를 부착한 인장 시험기를 사용하였으며, 시료는 두 종류의 polyacrylonitrile-polyvinylchloride 공중합체와 또 다른 두 종류의 PVC 모노 필라멘트 섬유를 여러 온도의 공기와 물속에서 응력완화 실험을 하였다.

• 콘크리트학회논문집
• /
• 제28권4호
• /
• pp.481-488
• /
• 2016

콘크리트는 공용기간동안 구조물 자체의 자중 및 이동 하중에 따른 응력을 받게 되며, 이러한 응력은 구조적인 거동뿐 아니라 내구적인 거동에도 영향을 준다. 대단위 콘크리트 부재의 시공은 시공이음을 요구하는데, 면처리 불량 또는 이어치기의 지연에 의해 콜드조인트가 발생하게 된다. 이러한 콜드조인트는 전단력에 취약할 뿐 아니라 염화물 확산성에도 영향을 미친다. 본 연구에서는 응력조건과 콜드조인트가 콘크리트의 염화물 확산에 미치는 영향을 정량적으로 평가하였다. 콜드조인트를 가진 콘크리트는 인장하중 수준이 30%에서 60%로 커질 때, 확산계수는 꾸준하게 증가하여 건전부와 큰 차이를 보이지 않았다. 그러나 압축부에서는 하중재하 30% 수준부터 콜드조인트 콘크리트에서 염화물 확산계수가 크게 증가하여 확산계수가 170% 이상 증가하였다. 이러한 특성은 압축하중을 받는 건전부 콘크리트와 큰 차이가 있으므로 이음부를 가지는 콘크리트의 내구성 설계에 주의가 필요하다.

• Geomechanics and Engineering
• /
• 제7권4호
• /
• pp.403-430
• /
• 2014

Shale gas formations exhibit strong mechanical and strength anisotropies. Thus, it is necessary to study the effect of anisotropy on the hydraulic fracture initiation pressure. The calculation model for the in-situ stress of the bedding formation is improved according to the effective stress theory. An analytical model of the stresses around wellbore in shale gas reservoirs, in consideration of stratum dip direction, dip angle, and in-situ stress azimuth, has been built. Besides, this work established a calculation model for the stress around the perforation holes. In combination with the tensile failure criterion, a prediction model for the hydraulic fracture initiation pressure in the shale gas reservoirs is put forward. The error between the prediction result and the measured value for the shale gas reservoir in the southern Sichuan Province is only 3.5%. Specifically, effects of factors including elasticity modulus, Poisson's ratio, in-situ stress ratio, tensile strength, perforation angle (the angle between perforation direction and the maximum principal stress) of anisotropic formations on hydraulic fracture initiation pressure have been investigated. The perforation angle has the largest effect on the fracture initiation pressure, followed by the in-situ stress ratio, ratio of tensile strength to pore pressure, and the anisotropy ratio of elasticity moduli as the last. The effect of the anisotropy ratio of the Poisson's ratio on the fracture initiation pressure can be ignored. This study provides a reference for the hydraulic fracturing design in shale gas wells.