• Journal of Information Display
• /
• v.10 no.4
• /
• pp.175-179
• /
• 2009

As the physical properties of nematic liquid crystals vary with respect to temperature, the performances of liquid crystal displays (LCDs) are highly dependent on temperature. Additionally, it is well known that the electro-optic characteristics of LCDs, such as transmittance and threshold voltage, also rely on the LCD switching modes. The temperature dependence of the electro-optic characteristics of the wide-viewing-angle LCD modes, such as in-plane switching (IPS), multidomain vertical alignment by patterned electrode (PVA), and fringe-field switching (FFS), have been studied, and the results showed that the FFS mode has lower temperature dependence compared to the IPS and PVA modes. Since the liquid crystal (LC) reorients in different ways in each mode, this result is associated with the temperature dependence of LC's bend and twist elastic constants, and also with the position of the main reorientation, either in the middle or on the surface of the LC layer.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.158-161
• /
• 1991

A new analytical expression for the temperature variation characteristics of hydrogenerated amorphous silicon (a-si:H) thin film transistors, between 223K and 433K, is presented and experimentally virified. The result show that the experimental transfer and output characteristics at several temperatures are easily modeled between $-50^{\circ}C\;and\;90^{\circ}C$. The model is based on three function obtained from the experimental data of $I_D$ versus $V_G$. Theoretical results comfirm the simple form of the model in terms of the device geometry. It was determined that as the temperature increaseed, the saturated drain current increased.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.6
• /
• pp.58-64
• /
• 2003

The performance of vibration-based damage detection methods is dependent upon the accuracy of modal parameters measured from structures of interest. Vibration monitoring, performed on a structure under uncertain temperature conditions, results in the uncertainty in model parameters of the structure. In this study, an experiment on the effect of various temperatures on modal characteristics of steel plate-girders is presented. First, the model plate-girder used for the experiment is described. Second, natural frequencies measured from the structure, using two different excitation sources, are described. Third, natural frequencies measured from the structure, under various temperatures, are described. Finally, the relationship between measurement temperature and natural frequency is analyzed.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.432-437
• /
• 2012

Electrical properties of the laminated SMD-type PTC thermistor for microcircuit protection were investigated as a function of calcination and sintering temperature. $BaTiO_3$ with $Y_2O_3$ and $MnO_2$ were calcined at 1000 to $1150^{\circ}C$ for 2h and the laminated SMD-type PTC thermistor was sintered at 1350 to $1400^{\circ}C$ for 2h in a reduced atmosphere (1% $H_2/N_2$). Sintered density of the sample was dependent on the calcination and sintering temperature. Electrical properties of the sintered samples were strongly dependent on the densities of samples. For the samples with density below 4.6 g/$cm^3$, the insulator characteristics were observed, while PTC jump characteristics (R150/R30) were disappeared for the sample with density above 5.05 g/$m^3$. Optimal PTC characteristics were obtained for the sintered samples with density of 5.05 g/$m^3$. The laminated SMD-type PTC thermistor prepared by calcination at $1100^{\circ}C$ for 2h and sintering at $1270^{\circ}C$ for 2h showed the room temperature resistivity of $11{\Omega}{\cdot}cm$ and PTC jump characteristics of $10^2$ order.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.7
• /
• pp.919-927
• /
• 1997

The main purpose of this study is to determine bifurcation as the primary instability of a glass melting furnace. Steady-state and unsteady characteristics of natural convection in the partially open cavity as appeared in a glass melting furnace is investigated by using numerical analysis. Three types of convection, such as steady laminar, unsteady periodic or unsteady quasi-periodic convection may occur according to the temperature difference between upper two isothermal surfaces along the depth of cavity in a glass melting furnace. In the temperature difference of 150-900 K between batch and free surface, the larger the temperature difference, the weaker the convection strength and unsteadiness. Since the glass viscosity is increasing exponentially in the lower temperature, the batch freezes the thermofluidic field especially below the surface of it. If the depth of cavity is 0.5 m, the bifurcation to time-dependent natural convection may occur in the range of 60-650 K. If that is 1.0 m, it may occur in the whole range of temperature difference.

• Transactions of Materials Processing
• /
• v.27 no.3
• /
• pp.160-164
• /
• 2018

The success of warm forming of Mg alloy sheets is very dependent on its frictional behavior at elevated temperatures. The effects of contact pressure and sliding length on the frictional characteristics of AZ31B Mg alloy sheet were investigated at elevated temperature and at room temperature. The contact pressure range for the friction test was determined through FE analysis of the roof panel which is a candidate for Mg alloy application. According to the experimental results, the frictional behavior of the Mg alloy sheet is equally highly influenced by both sliding length and contact pressure at room temperature. At elevated temperatures, however, the sliding length has a more dominant influence on the frictional characteristics of the Mg alloy sheet than the contact pressure, if the contact pressure is lower than a certain level.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.16 no.4
• /
• pp.109-116
• /
• 2008

Ground temperature restoration characteristics are the crucial factors to evaluate whether a ground source heat pump system can keep long time steady operation. They are mainly dependent on soil thermal properties, layout of pile group, operation/shutoff ratio, cooling/heating load, thermal imbalance ratio and so on. On the one hand, several types of vertical pile foundation heat exchangers are intercompared to determine the most efficient one by performance test and numerical method. On the other hand, according to the layout of pile group of a practical engineering and running conditions of a GSHP system in Shanghai, the temperature distribution during a period of five years is numerically studied. The numerical results are analyzed and are used to provide some guidance for the design of large-scale GSHP system.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.2
• /
• pp.222-227
• /
• 2009

The bias characteristics due to the changes of temperature and temperature gradient of fiber coil are investigated in fiber-optic gyroscope. The bias performance is degraded with the changes of temperature and temperature gradient of fiber coil. The temperature compensation using both the temperature-dependent bias measurement and the temperature-induced error model of fiber-optic gyroscope improves the bias stability about 3 times as much as the uncompensated original case, which leads to very stable bias performance over the temperature range from $-35^{\circ}C$ to $+77^{\circ}C$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.2
• /
• pp.105-114
• /
• 2015

Heated glasses are widely used to prevent surface condensation and freezing in ship and building windows. This study proposes a heated glass temperature control system composed of power and control circuits to control the temperature of heated glasses. The proposed temperature control system adopts a digital controller instead of a conventional analog controller. Thus, the proposed system has better characteristics, such as precise setup and control of glass temperature, setup and control of output power, and control mode change between ON/OFF and phase controls. The system can also implement multi-functional control algorithms. The control characteristics are not dependent upon external disturbances, such as ambient temperature and electrical noises. Furthermore, the proposed temperature control system utilizes the power line communication (PLC) method to control the number of heated glasses without any extra communication lines. The system proposes a new communication protocol with strong immunity to electrical switching noises. A new sensorless algorithm is used to detect the temperature of the heated glass. This study presents the design guidelines in detail and its effectiveness are confirmed by implementing a 4-kw prototype temperature control system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.186-187
• /
• 2007

In this work, a temperature stable PWM(Pulse width modulation) circuit is proposed. The designed PWM circuit has a temperature dependent current source and a temperature independent voltage to compensate electrical characteristics with operating temperature. The variation of driving current is from about 4% to -6% in the temperature range $0^{\circ}C\;to\;70^{\circ}C$ compared to the current at the room temperature. The variation of bandgap voltage reference is from about 1.3% to -0.2% with temperature when the supply voltage is 3.3 volts. From simulation results, the variation of output pulse width is less than from 0.86% to -0.38% in the temperature range $0^{\circ}C\;to\;70^{\circ}C$.