• Journal of Applied Reliability
• /
• v.17 no.2
• /
• pp.92-102
• /
• 2017

Purpose: Reliability prediction standards consider environmental conditions, such as temperature, humidity and vibration in order to predict the reliability of the electronics components. There are many types of standards, and each standard has a different failure rate prediction model, and requires different environmental conditions. The purpose of this study is to make a sensitivity analysis by changing the temperature which is one of the environmental conditions. By observing the relation between the temperature and the failure rate, we perform the sensitivity analysis for standards including MIL-HDBK-217F, RiAC-HDBK-217Plus and FIDES. Methods: we establish environmental conditions in accordance with maneuver weapon systems's OMS/MP and mission scenarios then predict the reliability using MIL-HDBK-217F, RiAC-HDBK-217Plus and FIDES through the case of DC-DC Converter. Conclusion: Reliability prediction standards show different sensitivities of their failure rates with respect to the changing temperatures.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.288-292
• /
• 1998

In this paper, we fabricated $SnO_2$ composite ceramics doped with 0~20mol% $SnO_2$ of bulk type to investigate the CO and $H_2$ gas sensitivity in various composition, temperature, and concentration of CO and $H_2$ gas. At the temperature range from $100^{\circ}C\sim425^{\circ}C$, the measured 1000ppm and 250ppm CO gas sensitivities of $SiO_2-SnO_2$composite ceramics were about 1.0~7.6 and 1.0~5.6, respectively. These values were about 1.0~1.5 times larger than pure $SnO_2$. The maximum 1000ppm CO gas sensitivity of $SiO_2-SnO_2$composites were measured around $325^{\circ}C$. At the temperature range from $270^{\circ}C\sim380^{\circ}C$, the 1000ppm and 500ppm $H_2$gas sensitivities of $SiO_2-SnO_2$ composites were about 2.9~21.2 and 2.1~11.3, respectively. Also the maximum 1000, 500 ppm $H_2$ gas sensitivities of samples were measured around.

• Korean Journal of Remote Sensing
• /
• v.29 no.6
• /
• pp.589-593
• /
• 2013

Sea Surface Temperature (SST) is the temperature close to the ocean's surface and affects the Earth's atmosphere as an important parameter for the climate circulation and change. The SST from satellite still has biases from the error in specifying retrieval coefficients from either forward modeling or instrumental biases. So in this paper, we performed sensitivity analysis using input parameter of the SST to notice that the SST is most affected among the input parameter. We used Infrared (IR) data from the Communication, Ocean, and Meteorological Satellite (COMS)/Meteorological Imager (MI) from April 2011 to March 2012. We also used the Global Space-based Inter-Calibration System (GSICS) correction to quality of the IR data from COMS. SST was calculated by substituting the input parameters; IR data with or without the GSICS correction. The results of this sensitivity analysis, the SST was sensitive from -0.0403 to 0.2743 K when the IR data were changed by the GSICS corrections.

• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.5
• /
• pp.239-243
• /
• 2012

$SnO_2$ thin films were prepared on the Si substrate by radio frequency (RF) magnetron sputtering and then post deposition vacuum annealed to investigate the effect of annealing temperature on the structural properties and hydrogen gas sensitivity of the films. The films that annealed at $300^{\circ}C$ show the higher sensitivity than the other films annealed at $150^{\circ}C$. From atomic force microscope observation, it is supposed that post deposition annealing promotes the rough surface and also, increase gas sensitivity of $SnO_2$ films for hydrogen gas. These results suggest that the vacuum annealed $SnO_2$ thin films at optimized temperatures are promising for practical high-performance hydrogen gas sensors.

• Journal of the Korean Ceramic Society
• /
• v.36 no.12
• /
• pp.1322-1326
• /
• 1999

In2O3 thick film gas sensor for detecting NOx gas of high concentration was fabricated by a screen printing technique. This work focussed on investigation of the change of sensitivity to NOx gas with firing temperatures of sensing layer and on improvement of the sensitivity by adding catalysts such as Al,. Ru, and SnO2 The cross sensitivites of sensor to CO, H2, CH4 and i-C4H10 gases were also examined under NO2 gas concentration of 200ppm Pure In2O3 gas sensor prepared at a firing temperature of 50$0^{\circ}C$ showed a maximum sensitivity to NOx gas at the operating temperature of 40$0^{\circ}C$ Al(0.004 wt%)-In2O3 sensor largely improved the sensitivities to both NO2 and NO gas and showed a superior selectivity compared with other gas sensors.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.10
• /
• pp.800-809
• /
• 2008

Scanning Thermal Microscope (SThM) is the tool that can map out temperature or the thermal property distribution with the highest spatial resolution. Since the local temperature or the thermal property of samples is measured from the extremely small heat transferred through the nanoscale tip-sample contact, improving the sensitivity of SThM probe has always been the key issue. In this study, we develop a new design and fabrication process of SThM probe to improve the sensitivity. The fabrication process is optimized so that cantilevers and tips are made of thermally grown silicon dioxide, which has the lowest thermal conductivity among the materials used in MEMS. The new design allows much higher tip so that heat transfer through the air gap between the sample-probe is reduced further. The position of a reflector is located as far away as possible to minimize the thermal perturbation due to the laser. These full $SiO_2$ SThM probes have much higher sensitivity than that of previous ones.

• Journal of Sensor Science and Technology
• /
• v.22 no.5
• /
• pp.315-320
• /
• 2013

In this paper, the properties of strain sensors made of spin-capable multi-walled carbon nanotubes (MWCNTs) were characterized and their sensing mechanisms analyzed. The key contribution of this paper is a new fabrication technique that introduces a simpler transfer method compared to spin-coating or dispersion CNT. Resistance of the MWCNT sheet strain sensor increased linearly with higher strain. To investigate the effect of CNT concentration on sensitivity, two strain sensors with different layer numbers of MWCNT sheets (one and three layers) were fabricated. According to the results, the sensor with a three-layer sheet showed higher sensitivity than that with one layer. In addition, experiments were conducted to examine the effects of environmental factors, temperature, and gas on sensor sensitivity. An increase in temperature resulted in a reduction in sensor sensitivity. It was also observed that ambient gas influenced the properties of the MWCNT sheet due to charge transfer. Experimental results showed that there was a linear change in resistance in response to strain, and the resistance of the sensor fully recovered to its unstressed state and exhibited stable electromechanical properties.

• Journal of Sensor Science and Technology
• /
• v.29 no.6
• /
• pp.382-387
• /
• 2020

Hydrogen (H₂) is considered as a new clean energy resource for replacing petroleum because it produces only H₂O after the combustion process. However, owing to its explosive nature, it is extremely important to detect H₂ gas in the ambient atmosphere. This has triggered the development of H₂ gas sensors. 2-dimensional (2D) graphene has emerged as one of the most promising candidates for chemical sensors in various industries. In particular, graphene exhibits outstanding potential in chemoresistive gas sensors for the detection of diverse harmful gases and the control of indoor air quality. Graphene-based chemoresistive gas sensors have attracted tremendous attention owing to their promising properties such as room temperature operation, effective gas adsorption, and high flexibility and transparency. Pristine graphene exhibits good sensitivity to NO₂ gas at room temperature and relatively low sensitivity to H₂ gas. Thus, research to control the selectivity of graphene gas sensors and improve the sensitivity to H₂ gas has been performed. Noble metal decoration and metal oxide decoration on the surface of graphene are the most favored approaches for effectively controlling the selectivity of graphene gas sensors. Herein, we introduce several strategies that enhance the sensitivity of graphene gas sensors to H₂ gas.

• Journal of Plant Biology
• /
• v.36 no.1
• /
• pp.59-66
• /
• 1993

In maize coleoptile segments where auxin transport capacity decreases with time following excision, susceptability of the tissue to transport inhibitors such as N-1-naphthylphthalamic acid (NPA), 3,4,5-triiodobenzoic acid (TIBA) or high concentrations of IAA was found to be rather increased. A time-dependent increase in the sensitivity to NPA can be postulated since the dose-response curve for NPA was shifted in the‘aged’tissue to the left (i.e. lower concentration). Preincubation of the tissue at a low temperature abolished the time-dependent sensitivity change, suggesting that cellular metabolism could be involved. The NPA-sensitive state was also brought about by calcium depletion of the tissue, which can be partially reversed by addition of calcium. Presence of exogenous IAA in the preincubation medium kept the auxin transport system from decay, implicating auxin as an endogenous controlling factor. Results of our experiments indicate a reversible, time-dependent changes of auxin transport system in which transport capacity and sensitivity to NPA are tightly coupled. Changes in the sensitivity to NPA were also seen in auxin action as well.

• Journal of Ship and Ocean Technology
• /
• v.8 no.3
• /
• pp.50-60
• /
• 2004

In this paper, a continuum-based design sensitivity analysis (DSA) method is developed for the weakly coupled thermo-elasticity problems. The temperature and displacement fields are described in a common domain. Boundary value problems such as an equilibrium equation and a heat conduction equation in steady state are considered. The direct differentiation method of continuum-based DSA is employed to enhance the efficiency and accuracy of sensitivity computation. We derive design sensitivity expressions with respect to thermal conductivity in heat conduction problem and Young's modulus in equilibrium equation. The sensitivities are evaluated using the finite element method. The obtained analytical sensitivities are compared with the finite differencing to yield very accurate results. Extensive developments of this method are useful and applicable for the optimal design problems incorporating welding and thermal deformation problems.