• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.646-653
• /
• 2001

LQG/LTR Control Methology is recently used for the analysis of multi-variable control in frequency domain. Target filter loop is designed by the demanding requirements such as cross-over frequency, disturbance rejection in low frequency domain, zero steady-state error, identification of maximum and minimum singular values and sensor noise rejection in high frequency domain. Loop transfer recovery is accomplished by solving the cheap control and then simulation close to the target filter loop. In this study, LQG/LTR Control Methodology is applied to the seat suspension system. It is found that this technique is very effective to control the system and improve the ride quality of human body.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.564-569
• /
• 2000

Model Based Compensator(MBC) is recently used for the analysis of multi-variable control in frequency domain. Target loop is designed by the demanding requirements such as cross-over frequency, disturbance rejection in low frequency domain, zero steady-state error, identification of maximum and minimum singular values and sensor noise rejection in high frequency domain. Loop transfer recovery will be continued in frequency domain until the plant with MBC comes close to the target loop. In this study, the technique using MBC is applied to the elevator vibration control system. It is found that this technique is very effective to control the vibration system.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.4
• /
• pp.534-542
• /
• 2017

This paper presents a fast locking technique for a fractional-N PLL frequency synthesizer. The technique directly measures $K_{VCO}$ on a chip, computes the VCO's target tuning voltage for a given target frequency, and directly sets the loop filter voltage to the target voltage before the PLL begins the normal closed-loop locking process. The closed-loop lock time is significantly minimized because the initial frequency of the VCO are put very close to the desired final target value. The proposed technique is realized and designed for a 4.3-5.3 GHz fractional-N synthesizer in 65 nm CMOS and successfully verified through extensive simulations. The lock time is less than $12.8{\mu}s$ over the entire tuning range. Simulation verifications demonstrate that the proposed method is very effective in reducing the synthesizer lock time.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.1028-1033
• /
• 1992

Loop shaping techniques are developed for the LQG/LTR controller design of singular multivariable sytems. One approach is to use the mode form of plant and the other is to replace the eigenvalues at 0 by ones at .epsilon.(.rarw.0). These two concepts for the target filter loop design are applied to a flight autopilot. And it is shown that these techniques are effective ones for the desired loop-shaping of singular multivariable systems.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.5
• /
• pp.35-41
• /
• 1998

This paper presents a decoupling controller of the missile seeker scan loop with a spin-stabilized platform. A precise seeker motion with respect to the scan command is essential for the higher acquisition probability of the target. As the seeker scan loop is a deeply cross-coupled two input two output system, an accurate pointing or scanning for each axis to the target is very difficult, even though provided with the help of a high performance controller. When a decoupling control is applied to the seeker scan loop, the cross-coupling between two axes can be reduced to a remarkable amount. As a low order of controller is required for the real time operation, a PI controller with decoupling filter is suggested and compared with other controllers. A linearized dynamic model of seeker scan loop is used and validated through the comparison of experimental results of step responses.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.1005-1010
• /
• 2005

In this paper, it is presented a frequency modulated continuous wave radar (FMCW) for distance measurement. The frequency range is $10{\sim}11$ GHz and the sweep time of the signal is 100 ms. The test target is 0.8 m2 of metal plate. The experiment is performed in open ground and the pyramidal horn antenna of about 22 dBi gain is used. The beat frequency according to the target moving to 40 m is measured. There is a good agreement between measured and calculated results. But the resolution of the FMCW radar is not good such as about 10 cm. It is result from the nonlinear signal of voltage controlled oscillator (VCO). To improve the nonlinear characteristic of VCO, a high pass filter and phase locked loop (PLL) frequency synthesizer are included in the radar system.

• The Journal of the Acoustical Society of Korea
• /
• v.30 no.2
• /
• pp.107-113
• /
• 2011

This paper describes a development of a loop filter design in a physical modeling of the plucked string instrument. The conventional method proposed by V$\"{a}$lim$\"{a}$ki cannot estimate right parameters if a sound has either very short sustain or no sustain. In order to overcome this drawback, we propose the use of the decay region and 5 to 20 harmonics of the sound in the estimation of loop filter parameters. The most appropriate filter coefficient is chosen by frequency signal to noise ratio. To verify the performance of the proposed method, the guitar, gayageum and geomungo were selected as the target because they have different shape, structure, and material of strings. Regardless of the duration of harmonics, the proposed method was able to estimate the loop filter parameters representing frequency-dependent damping of harmonics.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.11
• /
• pp.873-880
• /
• 2020

In this paper, we propose a guidance filter to estimate line of sight rate with strapdown seeker measurements and INS(Inertial Navigation System) information. The measurements of proposed guidance filter consisted of the LOS(Line of Sight) and relative position that can be calculated with the seeker's measurements, INS information and known target position, also the filter is based on an asynchronous filter to use outputs of the two sensors that are out of synchronous and period. Through the proposed filter, we can reduce the effect on parasitic loop that can be caused by using large time delay seeker and improve the estimation performance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.4A
• /
• pp.429-438
• /
• 2004

In this paper, a decision-feedback coherent code tracking loop is designed for WCDMA systems and its performance is analyzed in terms of jitter variance considering the effect of phase and symbol estimation errors for both AWGN and fading environments. An analytical closed-form formula for jitter variance is Int derived for AWGN environments as a function of a pulse-shaping filter, timing offset, signal-to-interference ratio, and loop bandwidth while involving the phase estimation error and bit error rate, and the upper bound of jitter variance is derived for fading environments. Finally a second-order coherent code tracking loop is designed with the DPCH frame format #13 of the WCDHA forward link selected as a target system, and its performance is evaluated by the closed-form formula and compared with the simulation results for both AWGN and Rayleigh fading environments.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.102-108
• /
• 2011

LQG/LTR control scheme is applied to the two axes stage using piezoelectric actuator for tracking reference input and suppressing hysteresis effect in this paper. The plant is combined with an integrator to improve the tracking ability. LQG/LTR controller is designed by making desirable target filter loop remove all poles except for an integrator included in new design plant model and loop transfer recovery. Decoupler in the shape of FIR filter is added to remove the coupling effect between the two axes motion and so feedback control loop is designed independently for the each axis motion.