• The Journal of Engineering Geology
• /
• v.31 no.4
• /
• pp.541-547
• /
• 2021

To assess the stability of a slope and the likelihood of its loss or collapse requires information about the ground, such as the composition of the stratum and its mechanical characteristics. This information is generally gathered through standard penetration testing (SPT) and cone penetration testing. SPT is not widely used due to problems with accessing slopes, most of which are steep and without ramps. A drop cone penetrometer, a portable device that can make up for these shortcomings, can be used in a limited way in some circumstances. Therefore, we developed a portable drilling machine and a small dynamic cone penetration test module that can easily access a slope site and perform SPT. The correlation of the developed system's results with those from SPT was analyzed. Analysis of the correlation between the energy shear rate passing to the load during the different test types established that the energy shear rate is reflected in the test result. The correlation between corrected dynamic cone penetration testing and corrected SPT was N_d' = 3.13 N'.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.5
• /
• pp.134-140
• /
• 2015

A control program of an engine control module (ECM) was developed, and its control performance was verified on a 750Ps marine diesel engine. The control method was designed for an engine rotational speed control system. For ECM hardware, the commercial rapid control prototype (RCP) ECM was used. The programming tool for control algorithm development was the MatLab/Simulink. The main control algorithm assembled many control models as engine cranking, run, and stall. Each model has sub-models to input/output control signals. The target engine speed was input signal from a speed control lever, and control output signal of the ECM was sent to the unit-injectors for fuel injection. The engine test was performed under various conditions of engine rotational speeds and dynamometer loads. The test results show that the control function of the ECM is suitable for electrical marine diesel engines.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.91-94
• /
• 2008

The designed module save to memory after received Image from CMOS image Sensor(CIS), and set a motion of Encoder module, read from memory per one macroblock each original Image and reference image then supply or save. the time required 470 cycle when processed one macroblock. For designed construct verification, I develop reference Encoder C like JM 9.4 and I proved this module with test vector which achieved from reference encoder C.

• Smart Structures and Systems
• /
• v.30 no.2
• /
• pp.159-172
• /
• 2022

To improve the accuracy of the standard penetration test (SPT) results, smart measurement system, which considers the energy transfer ratio into the sampler (ETR_Sampler), is required. The objective of this study is to evaluate the effects of joints and rod length on the transferred energy into the sampler. The energy transfer ratios into the rod head (ETR_Head) and ETR_Sampler, and the energy ratio from the head to the sampler (ER_HS) were obtained using energy modules, which were installed at the rod head and above the SPT sampler. Linear regression analyses are conducted to correlate the ER_HS with the number of joints, rod length, and SPT N-values. In addition, the dynamic resistances are calculated using both transferred energies into the rod head and into the sampler, and are compared with the corrected cone tip resistance measured from the cone penetration test (CPT). While the ETR_Head are generally constant, but the ETR_Sampler and ER_HS gradually decrease along the depth or the number of joints, except at certain depths with high SPT N-values. Thus, the ER_HS can be estimated using the number of joints, rod length, and SPT N-values. The dynamic resistance evaluated by E_Sampler produces a better correlation with the corrected cone tip resistance than that by E_Head. This study suggests that transferred energy into the SPT sampler may be effectively used for more accurate subsurface characterization.

• Korean Journal of Optics and Photonics
• /
• v.5 no.3
• /
• pp.423-430
• /
• 1994

We designed and fabricated the single mode fiber pigtailed DFB-LD module for 2.5 Gbps optical communication system. In the design of the DFB-LD module, we made the module divided into two parts of inner sub-module and outer 14-pin butterfly package and cylindrical shaped sub-module contain quasi confocal 2 lens system including optical isolator and electrical connection between these parts via hybrid substrate of bias T circuit. Laser welding was used to assemble the sub-module which requires accurate fixing between optical elements. The fabricated DFB-LD module showed optical coupling efficiency of 20% and - 3 dB small signal response of more than 2.6 GHz. We confirmed mechanical reliability of the module by temperature cycle test where the tested module exhibit optical power fluctuation of less than 10%. Finally we evaluated the performance of the fabricated DFB-LD module as light source of 2.5 Gbps optical communication system, sensitivity of - 30.2 dBm was obtained through 47 km optical fiber transmission under the criterion of $1\times10^{-10}$ BER and transmission penalties were 1.5 dB caused by extinction ratio and 1.0 dB caused by chromatic dispersion of normal single mode fiber. fiber.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.6
• /
• pp.439-444
• /
• 2020

An increase in the temperature of photovoltaic (PV) modules causes reduced power output and shorter lifetime. Because of these characteristics, demands for the heat dissipation of PV modules are increasing. In this study, we attached a heat dissipation sheet to the back sheet of a shingled PV module and observed the temperature changes. The PV shingled module was tested under Standard Test Conditions (STCs; irradiance: 1,000 W/㎡, temperature: 25℃, air mass: 1.5) using a solar radiation tester, wherein the temperature of the PV module was measured by irradiating light for a certain duration. As a result, the temperature of the PV module with the heat dissipation sheet decreased by 3℃ compared to that without a heat dissipation sheet. This indicated that the power loss was caused by a temperature increase of the PV module. In addition, it was confirmed that the primary parameter contributing to the reduced PV module output power was the open circuit voltage (Voc).

• Proceedings of the KIPE Conference
• /
• 2018.11a
• /
• pp.163-164
• /
• 2018

본 논문에서는 새로운 MMC(Modular Multilevel Converter)용 SM(Sub-Module) 시험회로와 이를 제어하기 위한 제어기법을 제안한다. 계통연계형 MMC 시스템에서 한 상의 암(arm)에 흐르는 전류는 계통주파수의 2고조파 성분과 DC 전류를 포함하고 있다. 제안하는 시험회로는 암 전류를 선형적으로 근사화하고, 시험전류의 DC 성분을 제어하여 시험할 SM의 전압을 일정하게 유지한다. 시뮬레이션을 통해 제안하는 SM 시험회로와 제어의 타당성을 검증하였다.

• The Bulletin of The Korean Astronomical Society
• /
• v.45 no.1
• /
• pp.70.3-70.3
• /
• 2020

Previous numerical simulations on planet-disk interactions revealed a lot of interesting phenomena including the planetary migration and the formation of many sub-structures inside the disks. However, these simulations were limited to an isothermal or adiabatic equation of state which does not account for various heating and cooling processes in the disks. Recent studies showed that the behavior of the planet-disk interaction can be significantly influenced by the disk thermodynamics. We develop a radiative diffusion module based on the two-temperature flux-limited diffusion approximation accounting for viscous heating and the accretion feedback. In this presentation, we describe our radiative diffusion solver, present some test results, and discuss potential applications of the module to planet-disk interactions,

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.209.2-209.2
• /
• 2012

UFFO Burst Alert & Trigger telescope (UBAT) is one of major instruments of UFFO-Pathfinder. The UBAT aims at 10 arcmin resolution localization of Gamma Ray Bursts with X-ray coded mask technique. It has $400mm{\times}400mm$ coded mask aperture, hopper, shielding and detector module with effective area of $191cm^2$. The detector module consists of an assembly of 36 64-ch MAPMTs and $25mm{\times}25mm$ pixellated YSO crystal array, and associated analog and digital electronics of about 2500 channels. We performed a vibration test using a dummy MAPMT with the detector module structure to measure the indused stress applied onto the MAPMT. We designed a sub-structure on the detector module to avoid the resonance that would otherwise deforms the detector module structure. A finite element analysis confirms the reduction of the load acceleration down to 12g. The experimental results are to be reported. Consequently, it proves that the MAPMT arrays of the flight UBAT detector module structure would survive in the space launch environment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.2C
• /
• pp.143-149
• /
• 2002

Complexity of the hardware system grows larger, the fault testing becomes more difficult. As we divide system into the functional sub-modules and analyze reliability of a sub-modules on the system, We improve the system test performance. And the analysing results help us to set up the effective strategies for the system test. Also describing the system to a formalized sub-modules, we can analyze the logical accuracy and the characteristics of system. So we can predict the reliability of the system based on execution characteristics. In this paper we propose a reliability analysis method of a system based on the execution characteristics of sub-module.