• Journal of Environmental Science International
• /
• v.5 no.5
• /
• pp.593-603
• /
• 1996

A dual-porosity filmed agglomerate model for the porous cathode of the molten carbonate fuel has been investigated to predict the cell performance. A phenomenological treatment of molecular, kinetic and electrode parameters has been given. The major physical and chemical phenomena being modeled include mass transfer, ohmic losses and reaction kinetics at the electrode- electrolyte interface. The model predicts steady-state cell performance, given the above conditions that characterize the state of the electrode. Quasi-linearization and finite difference techniques are used to solve the coupled nonlinear differential equations. Also, the effective surface area of electrode pore was obtained by mercury porosimeter. The results of the investigation are presented in the form of plots of overpotential vs. current density with varied the electrode material, gas composition and mechanism. The predicted polarization curves are compared with the empirical data from 1 c$m^2$ cell. A fair correspondence is observed.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.34 no.2
• /
• pp.212-222
• /
• 1998

Heat transfer performance improvement by fin and groovs is studied for condensation of R-11 on integral-fin tubes. Eight tubes with trapczodially shaped integral-fins having fin density from 748 to 1654fpm(fin per meter) and 10, 30 grooves are tested. A plain tube having the same diameter as the finned tubes is also used for comparison. R-11 condensates at saturation state of 32 $^{\circ}C$ on the outside tube surface coded by inside water flow. All of test data are taken at steady state. The heat transfer loop is used for testing singe long tubes and cooling is pumped from a storage tank through filters and folwmeters to the horizontal test section where it is heated by steam condensing on the outside of the tubes. The pressure drop across the test section is measured by menas pressure gauge and manometer. The results obtained in this study is as follows : 1. Based on inside diameter and nominal inside area, overall heat transfer coefficients of finned tube are enhanced up to 1.6 ~ 3.7 times that of a plain tube at a constant Reynolds number. 2. Friction factors are up to 1.6 ~ 2.1 times those of plain tubes. 3. The constant pumping power ratio for the low integral-fin tubes increase directly with the effective area to the nominal area ratio, and with the effective area diameter ratio. 4. A tube having a fin density of 1299fpm and 30 grooves has the best heat transfer performance.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.3
• /
• pp.20-28
• /
• 2015

Performance parameters of solid rocket motor with multi axis pintle nozzles were analyzed theoretically and modeled. For figuring out the governed variable of dynamic characteristics of system, dynamic analysis was done by using established model. To present characteristics of this system, the model should include not only internal ballistics of propulsion unit but also actuating system to move pintle. For solid rocket motor with multi axis pintle nozzles, not only performance of steady state but also dynamic characteristic of transient state is important design parameter to precise thrust control. Therefore, response time of open-loop system was analyzed by using established model and requirement about response time was satisfied by controlling pressure.

• Journal of Power Electronics
• /
• v.19 no.3
• /
• pp.784-793
• /
• 2019

Two objectives can be pursued simultaneously with the ${\delta}$ control of a single-phase electric spring (ES). These objectives are the stabilization of the voltage across the critical load (CL) of a power system, and the achievement of a specific functionality similar to the pure compensation of reactive power or the correction of the power factor. However, existing control systems implementing the ${\delta}$ control do not cope with non-ideal operating conditions, such as line voltage distortions, and exhibit a somewhat sluggish regulation of the CL voltage. In an effort to improve both the steady-state and transient performances of an ES power system, this paper proposes implementing the ${\delta}$ control by means of a control system built up on the repetitive control and assisted by state feedback with pole assignment. This paper starts by analyzing the dynamics of an ES power system in terms of its poles and zeros. After that, a reduced second-order model of the dynamics is formulated to avoid a notch filter in the pole assignment. A repetitive control for an ES power system is then designed to meet the two above mentioned objectives. Experimental tests carried out on a laboratory setup demonstrate the effectiveness of the proposed control system in significantly improving the ES power system performance, while reaching the two objectives. In particular, the tests outline the large mitigation of harmonics in the CL voltage under line voltage distortions and its fast stabilization action.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.2 no.2
• /
• pp.39-46
• /
• 1982

A model of substrate removal by rotating discs has been developed for a better understanding of the process, and the performance of the system has been evaluated under steady and unsteady state. The model was constructed based upon mass transfer of the substrate from the bulk solution to the biofilm and a simultaneous removal of the substrate by the biomass. The model is composed of a few sets of differential equations representing mass balance within the elements of a liquid film and a biofilm, and in the bulk solution. Substrate removal efficiency of the process is largely dependent on a diffusion coefficient of the substrate within the biofilm and a maximum rate of substrate removal of the biomass. The efficiency is affected to a greater extent when the substrate concentration is low and the maximum substrate removal rate is high. The efficiency increases proportionally with increasing film depth when the biofilm is shallow, however, the rate of increase gradually decreases with an increase of the film depth. As the film reaches a limiting depth, the efficiency remains constant. Unlike the steady state, the effluent quality is affected by the tank volume under dynamic state. Increasing tank volume decreases peak concentration of the effluent under peak loading. Additional tank volume provides a buffer capacitya.gainst a peak loading and the holding tank behaves like an equalization tank.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.63-72
• /
• 2010

MOV(Main Oxidizer shut-off Valves) control the combustion of launch vehicle systems by the supply and the isolation of liquid oxygen to a main combustion chamber in launch vehicle systems. Moreover, the MOV should secure a constant flow rate of liquid oxygen for combustion instability in the steady operational state. Although it has been showed that a EM(Engineering Model) with a high discharge coefficient value compared with the TM(Technology Model) fills the overall performance requirements, additional design modifications in some critical parts of the EM were conducted to improve the performance. The configurations of the pressure-control body, the middle flange, and the rips of the inlet body of the EM were modified and the performance tests have been performed with test models. Consequently, the intended improvements have been verified by the performance tests.

• Journal of KIISE:Information Networking
• /
• v.34 no.3
• /
• pp.193-202
• /
• 2007

In this paper, a performance evaluation model of the Multistage Interconnection Network(MIN) with the multiple-buffered crossbar switches under Hot-spot environment is proposed and examined. Buffered switch technique is well known to solve the data collision problem of the MIN. The proposed evaluation model is developed by investigating the transfer patterns of data packets in a switch. The performance of the multiple-buffered $a{\times}a$ crossbar switch is analyzed. Steady state probability concept is used to simplify the analyzing processes. Two important parameters of the network performance, throughput and delay, are then evaluated. To validate the proposed analysis model, the simulation is carried out on a Baseline network that uses the multiple buffered crossbar switches. Less than 2% differences between analysis and simulation results are observed. It is also shown that the network performance is significantly improved when the small number of buffer spaces is given. However, the throughput elevation is getting reduced and network delay becomes increasing as more buffer spaces are added in a switch.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.5
• /
• pp.52-61
• /
• 2015

This paper performed a numerical study to analyse the transient performance behavior of a turbofan engine with variable inlet guide vane (IGV) and bleed air schedules. The low bypass ratio mixed flow turbofan engine was considered in this study. For modeling the compressor performance with IGV, the performance maps were generated by using a one-dimensional meanline analysis and feed to the engine simulation program. The IGV and bleed air according to the rotating speed were scheduled to satisfy 10% of surge margin at steady-state condition. The transient engine performance analysis was conducted with the schedules. The engine with IGV schedule showed a higher surge margin and lower turbine inlet temperature than the engine with bleed air schedule during the transient period.

• Journal of KIISE:Information Networking
• /
• v.32 no.2
• /
• pp.244-253
• /
• 2005

In this paper, a performance evaluation model of the switch router with the multiple-buffered crossbar switches is proposed and examined. Buffered switch technique is well known to solve the data collision problem of the crossbar switch. The proposed evaluation model is developed by investigating the transfer patterns of data packets in a switch with output-buffers. The performance of the multiple-buffered crossbar switch is analyzed. Steady state probability concept is used to simplify the analyzing processes. Two important parameters of the network performance, throughput and delay, are then evaluated. To validate the proposed analysis model, the simulation is carried out on a network that uses the multiple buffered crossbar switches. Less than $2\%$ differences between analysis and simulation results are observed. It is also shown that the network performance is significantly improved when the small number of buffer spaces is given. However, the throughput elevation is getting reduced and network delay becomes increasing as more buffer spaces are added in a switch.

• Journal of KIISE:Information Networking
• /
• v.29 no.6
• /
• pp.738-748
• /
• 2002

In this paper, a performance evaluation model of the Multistage Interconnection Network(MIN) with the multiple-buffered crossbar switches is Proposed and examined. Buffered switch technique is well known to solve the data collision problem of the MIN. The proposed evaluation model is developed by investigating the transfer patterns of data packets in a switch with output-buffers. The performance of the multiple-buffered${\alpha}{\times}{\alpha}$ crossbar switch is analyzed. Steady state probability concept is used to simplify the analyzing processes, Two important parameters of the network performance, throughput and delay, are then evaluated, To validate the proposed analysis model, the simulation is carried out on a Baseline network that uses the multiple buffered crossbar switches. Less than 2% differences between analysis and simulation results are observed. It is also shown that the network performance is significantly improved when the small number of buffer spaces is given. However, the throughput elevation is getting reduced and network delay becomes increasing as more buffer spaces are added in a switch.