• Journal of Biosystems Engineering
• /
• v.26 no.6
• /
• pp.503-508
• /
• 2001

In this paper, time-fiequency analysis and multi-dimensional spectral analysis methods are applied for source identification and diagnosis of non-stationary sound/vibration signals. Sound or vibration problems of general vehicle and agricultural machinary are under 500 Hz. So We used linearly increased chirp signals under 500 Hz. By checking the coherences on concerned time, fur time-variant non-stationary signals, this simulation it very well coincident to expected results.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.32B no.6
• /
• pp.899-908
• /
• 1995

In this paper, the probabilistic relations of dual morphological operations, such as dilation and erosion, closing and opening, and close- open and open-close, and the statistical properties for a continuous stationary lst order Gauss-Markov source are analyzed. The result is that the dual filters have symmetrical means and skews, and equal variances. Also, the statistics of morphological filters are very similar with those of input source, as correlation coefficient increases.

• Proceedings of the Korean Information Science Society Conference
• /
• 2002.04b
• /
• pp.289-291
• /
• 2002

Host of source separation methods focus on stationary sources so higher-order statistics is necessary In this paler we consider a problem of source separation when sources are second-order nonstationary stochastic processes . We employ the natural gradient method and develop learning algorithms for both 1inear feedback and feedforward neural networks. Thus our algorithms possess equivariant property Local stabi1iffy analysis shows that separating solutions are always locally stable stationary points of the proposed algorithms, regardless of probability distributions of

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.138-142
• /
• 2006

Time Difference of Arrival (TDOA) algorithm was applied to sound source positioning. Using measured microphones signal, difference of distance from source to sensors were estimated by TDOA and speed of sound, and taken by navigational measurements. And iteration procedures were induced to find the actual source location. For the case of stationary and moving sound source, validation test were performed in the anechoic room. In the stationary case, the error of positioning is less then 1.3% in length scale, and it could be seen proper filtering processes were required in the application of moving sound source.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.9 s.252
• /
• pp.1154-1159
• /
• 2006

In this paper, time-frequency analysis and multi-dimensional spectral analysis methods are applied to source identification and diagnostic of non-stationary sound vibration signals. By checking the coherences for concerned time, this simulation is very well coincident to expected results. The proposed method analyzes the signal instantaneously in both time and frequency domains. The MDSA (Multiple Dimensional Spectral Analysis) analyzes the signal in the plane of instantaneous time and instantaneous frequency at the same time. And it was verified by using the 1500cc passenger car which is accelerated from 70Hz to 95Hz in 4 seconds, the proposed method is effective in determining the vehicle diagnostic problems.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.10a
• /
• pp.147-152
• /
• 2012

An instantaneous environmental noise simulation method emitted by a moving high-speed train by quasi-stationary analysis is proposed in this study. In the method, the propagation attenuations from stationary point sources on segmented railways to a receiver are calculated using a general purpose environmental noise prediction program ENPro based on the ISO 9613-2 method. Then, the instantaneous environmental noise at a receiver due to a moving high-speed train considering convection effect is evaluated with the information on the propagation attenuations from the instantaneous train location to the receiver and the sound power levels and directivity of stationary point sources evaluated by German Schall 03 (2006). To demonstrate the validity of proposed method, simulated and measured time history of instantaneous noise for KTX-I and KTX-II on running are compared and the results show that the method can be utilized for the train noise source identification as well as the simulation of instantaneous environmental noise emitted by a high-speed train.

• Journal of Environmental Science International
• /
• v.14 no.6
• /
• pp.543-553
• /
• 2005

In recent days, photochemical smog due to the rapid industry development and vehicle increasement has become a critical pollutant in the metropolitan area and the number of ozone alarm signal has increased every year. This research was performed to evaluate VOCs emission source characteristics and concentration of VOCs in Daegu. The site average concentration was observed in the following order: industrial area > commercial area > residential area. Most of the VOCs species except toluene showed variations with higher concentration during nighttime, and lower concentration during the daytime. The major VOCs of stationary emission source were BTEX(benzene, toluene, ethylbenzene. xylene) and methylene chloride, trichloroethene and styrene. Also, those of automobile exhaust were toluene and benzene. Also, the major VOCs concentration emited by the vehicle fuel was observed in the following order: gasoline > light oil > liquefied petroleum gas (L.P.G). Correlation coefficients values were estimated between major VOCs such as toluene, ethylbenzene, m,p-xylene, o-xylene. Results showed that correlation coefficient values were significant magnitude above 0.76. Also, there showed highly significant correlations among ethyl benzene, m,p-xylene, and o-xylene concentration(Pearson correlation coefficients, r=0.868-0.982). Calculated correlation coefficients among commercial area,industrial area and residential area were 0.934-0.981, they showed high correlation. There showed highly correlation between stationary emission source and industrial area, compared with commercial area and residential area. Also, calculated correlation coefficients among commercial area, industrial area, residential area and automobile exhaust were 0.732, 0.725, 0.777, respectively.

• Journal of Magnetics
• /
• v.16 no.4
• /
• pp.391-397
• /
• 2011

An inductance measurement method for interior permanent magnet synchronous machine (IPMSM) is proposed in this paper. In this method, the motor is measured at standstill condition, and only a 3-phase voltage source, an oscilloscope and a DC voltage source are required. Depending on the deductive dq-axis voltage equations in the stationary frame of reference, the dq-axis inductances at different current magnitude and vector angle can be calculated by the measured 3-phase voltages and currents. And hence, the saturation and cross-magnetizing effect of the inductances are measurable. This paper introduces the principle equations, experiment setup, data processing, and results comparison on the concentrated-winding and distributed-winding IPMSMs.

• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.994-1005
• /
• 2015

This paper presents a novel power control strategy for PWM current-source rectifiers (CSRs) in the stationary frame based on the instantaneous power theory. In the proposed control strategy, a virtual resistance based on the capacitor voltage feedback is used to realize the active damping. In addition, the proportional resonant (PR) controller under the two-phase stationary coordinate is designed to track the ac reference current and to avoid the strong coupling brought about by the coordinate transformation. The limitations on improving steady-state performance of the PR controller is investigated and mitigated using a cascaded lead-lag compensator. In the z-domain, a straightforward procedure is developed to analyze and design the control-loop with the help of MATLAB/SISO software tools. In addition, robustness against parameter variations is analyzed. Finally, simulation and experimental results verify the proposed control scheme and design method.

• International Journal of Aeronautical and Space Sciences
• /
• v.10 no.2
• /
• pp.125-133
• /
• 2009

To numerically simulate aerodynamics of rotor-airframe interaction in a rigorous manner, we need to solve the Navier-Stokes system for a rotor-airframe combination as a whole. This often imposes a serious computational burden since rotating blades and a stationary body have to be simultaneously dealt with. An efficient alternative is to adopt a momentum source method in which the action of rotor is approximated as momentum source over a rotor disc plane in a stationary computational domain. This makes the simulation much simpler. For unsteady simulation, the instantaneous momentum sources are assigned only to a portion of disk plane corresponding to blade passage. The momentum source is obtained by using blade element theory with dynamic inflow model. Computations are carried out for the simple rotor-airframe model (the Georgia Tech model) and the results of the simulation are compared with those of the full Navier-Stokes simulation with moving mesh system for rotor and with experimental data. It is shown that the present simulation yields results as good as those of the full Navier-Stokes simulation.