• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.9
• /
• pp.1268-1273
• /
• 2011

The present study was conducted to determine a feasible method of protein concentrate extraction from rice bran (RBPC) and its effect as a substitution for skim milk in early weaning pig diets. An investigation to extract protein concentrate from full fat rice bran was undertaken to determine the best ratio of water and rice bran, the amount of NaOH and a HCl solvent to use in a simple paddle-type mixer with modified spinning to produce RBPC. The results stated that the best ratio for water mixing in the RBPC extraction process was 1:5 with 20 g NaOH and 30 min in a paddle-type mixer at 300 rpm. A mix of 250 ml 0.2 N HCl was optimum for neutralization and protein precipitation. After the fluid was spun out with a washing machine, the sediment was left for 12-14 hours to complete the filtration. One kilogram of rice bran could produce an average of 324.5 gram RBPC and it contained 3.40% ash, 496.48 kcal of GE/100 gram, 1.94% crude fiber, 28.20% ether extract, 7.64% moisture and 16.66% crude protein, respectively. A total of 45 crossbred piglets, weaned at 3 weeks of age were allotted into control diet (A) and dietary treatments formulated with a four different rates of RBPC substitution for skim milk at a percentage of 25 (B), 50 (C), 77 (D) and 100 (E) respectively, in a randomized complete block (RCB) design. All piglets had free access to feed and water until 8 week of age when the experiment ended. Feed intake, average daily gain, growth rate and feed efficiency were not affected by dietary treatments. Blood test parameters after completion of the growth trial indicated normal health. Even though the mean of cell hemoglobin concentration was significantly different between treatments (p<0.05) it was still within the normal range. The cost difference for BW gain of 100% RBPC substituted for skim milk in the weaning diet was approximately 35% lower than that of the control and the relative cost of production was 96.67, 92.85, 70.75 and 64.48% lower for the replacement of 25, 50, 75 and 100% of skim milk respectively. These results implied that this technology is feasible for use by small scale farmers to improve their self-reliance.

• Journal of Sericultural and Entomological Science
• /
• v.7
• /
• pp.65-74
• /
• 1967

This work has been carried out to find the fundamental reasons of raw silk size nonuniformity by studying with the physical nature and its bave formation through the worm spinnerate with anatomical device. Mean time, the uniformity improving method is also attached to this paper after throughfall theoretical study. 1. According to the anatomical study of the silkworm spinnerate, the physical form decides the fiber cross section and also spinns more finner size as the spinning is continued collaborating with the muscle pressure and decrease of liquid silk in the silk gland. 2. The bave size deviation of the Korean cocoons have shown a little difference among the varieties, but, they are conclued as 0.58 denier in average which caused some size deviation of the raw silk inevitably. 3. The raw silk nonuniformity increases when the cocoon have size is not suitable with the proposed raw silk size. 4. The nonuniformity is also increased very much during the filature process in case of poor technical work, but even if we do our best, the best result is found as 30 percent improvement which is still worser than the natural cocoon size deviation. 5. It is required to be careful for the selection of silkworm variety in order to improve the nonuniformity of raw silk so that the bave size be suitable for the proposed silk. 6. The definite size silk reeling method could made better uniform silk, 20 percent at least, than the definite cocoon number silk reeling method. 7. A newly developed denier(21d) gauge was applied for the multiends type silk reeling machine which is widely used in Korea, and the result of the method showed 1.30 denier size deviation, but, in case of no use of it was 1.57 denier size deviation, that is, it could improve two grades more than the normal reeling method.

• Journal of Powder Materials
• /
• v.13 no.5 s.58
• /
• pp.327-335
• /
• 2006

In the development of new hydrogen absorbing materials for a next generation of metal hydride electrodes for rechargeable batteries, metastable Mg-Ni-based compounds find currently special attention. Amor phous-nanocrystalline $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ alloys were produced by mechanical alloying and melt-spinning and characterized by means of XRD, TEM and DSC. On basis of mechanically alloyed Mg-Ni-Y powders, complex hydride electrodes were fabricated and their electrochemical behaviour in 6M KOH (pH=14,8) was investigated. The electrodes made from $Mg_{63}Ni_{30}Y_7$ powders, which were prepared under use of a SPEX shaker mill, with a major fraction of nanocrystalline phase reveal a higher electrochemical activity far hydrogen reduction and a higher maximum discharge capacity (247 mAh/g) than the electrodes from alloy powder with predominantly amorphous microstructure (216 mAh/g) obtained when using a Retsch planetary ball mill at low temperatures. Those discharge capacities are higher that those fur nanocrystalline $Mg_2Ni$ electrodes. However, the cyclic stability of those alloy powder electrodes was low. Therefore, fundamental stability studies were performed on $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ ribbon samples in the as-quenched state and after cathodic hydrogen charging by means of anodic and cathodic polarisation measurements. Gradual oxidation and dissolution of nickel governs the anodic behaviour before a passive state is attained. A stabilizing effect of higher fractions of yttrium in the alloy on the passivation was detected. During the cathodic hydrogen charging process the alloys exhibit a change in the surface state chemistry, i.e. an enrichment of nickel-species, causing preferential oxidation and dissolution during subsequent anodization. The effect of chemical pre-treatments in 1% HF and in $10\;mg/l\;YCl_3/1%\;H_2O_2$ solution on the surface degradation processes was investigated. A HF treatment can improve their anodic passivation behavior by inhibiting a preferential nickel oxidation-dissolution at low polarisation, whereas a $YCl_3/H_2O_2$ treatment has the opposite effect. Both pre-treatment methods lead to an enhancement of cathodically induced surface degradation processes.

• Korean Chemical Engineering Research
• /
• v.58 no.3
• /
• pp.466-473
• /
• 2020

Fabric current collector can be a promising electrode material for Capacitive Deionization (CDI) system that can achieve energy-efficient desalination of water. The one of the most attractive feature of the fabric current collector is its high tensile strength, which can be an alternative to the low mechanical strength of the graphite foil electrode. Another advantage is that the textile properties can easily make shapes by simple cutting, and the porosity and inter-fiber space which can assist facile flow of the aqueous medium. The fibers used in this study were made of woven structures using a spinning yarn using conductive LM fiber and carbon fiber, with tensile strength of 319 MPa, about 60 times stronger than graphite foil. The results were analyzed by measuring the salt removal efficiency by changing the viscosity of electrode slurry, adsorption voltage, flow rate of the aqueous medium, and concentration of the aqueous medium. Under the conditions of NaCl 200 mg/L, 20ml/min and adsorption voltage 1.5 V, salt removal efficiency of 43.9% in unit cells and 59.8% in modules stacked with 100 cells were shown, respectively. In unit cells, salt removal efficiency increases as the adsorption voltage increase to 1.3, 1.4 and 1.5 V. However, increasing to 1.6 and 1.7 V reduced salt removal efficiency. However, the 100-cell-stacked module showed a moderate increase in salt removal efficiency even at voltages above 1.5 V. The salt removal rate decreased when the flow rate of the feed was increased, and the salt removal rate decreased when the concentration of the feed was increased. This work shows that fabric current collector can be an alternative of a graphite foil.

• Korean Chemical Engineering Research
• /
• v.56 no.6
• /
• pp.819-825
• /
• 2018

Porous nanofibers comprising hollow ${\alpha}-Fe_2O_3$ nanospheres were prepared by applying both template method and Kirkendall diffusion effect to electrospinning process. During heat-treatment processes, the solid Fe nano-metals formed by initial heat-treatment in the carbon matrix were converted into the hollow structured ${\alpha}-Fe_2O_3$ nanospheres. In particular, PS nanobeads added in the spinning solution were decomposed and formed numerous channels in the composite, which served as a good pathway for Kirkendall diffusion gas. The resulting porous nanofibers comprising hollow ${\alpha}-Fe_2O_3$ nanospheres were applied as an anode material for lithium-ion batteries. The discharge capacities of the nanofibers for the 30th cycle at a high current density of $1.0A\;g^{-1}$ was $776mA\;h\;g^{-1}$. The good lithium ion storage property was attributed to the synergetic effects of the hollow ${\alpha}-Fe_2O_3$ nanospheres and the interstitial nanovoids between the nanospheres. The synthetic method proposed in this study could be applied to the preparation of porous nanofibers comprising hollow nanospheres with various composition for various applications, including energy storage.

• Applied Chemistry for Engineering
• /
• v.22 no.5
• /
• pp.467-472
• /
• 2011

This study investigated illite/polypropylene (PP) composite filament formation via melt-spinning and evaluated their physical properties to prepare functional fibers using natural materials. When composite filaments were formed, the composite filaments exhibited smaller fiber diameters compared to that of neat PP filament because of the lubricant effect of illite induced by its layered structure. Moreover, fluorination effect increased interfacial affinity and dispersion in the polymer, resulting in smaller diameter of fluorinated illite/PP composite filament, which was 2/3 of the neat PP filament diameter. Addition of raw and fluorinated illite improved thermal stability of illite/PP composite filament. Raw illite/PP composite filament cannot be used for a practical application, because it broke during drawing process, whereas the fluorinated illite/PP composite filament can be used for a practical application, because it exhibited similar tensile strength of the neat PP filament and 50% increased modulus. Even with improved illite/PP interfacial affinity and illite dispersion in the polymer, illite/PP composite filament formed microcomposite, because non-expandable illite had strongly bound layers, resulting in only a little illite exfoliation and PP intercalation into illite.

• New Physics: Sae Mulli
• /
• v.68 no.11
• /
• pp.1208-1214
• /
• 2018

The one-step spin coating method is reported as an excellent thin film process because it can be easily used to fabricate high-quality methyl-ammonium lead tri-iodide ($MAPbI_3$) perovskite layers. One of the important things in the one-step spin coating method towards obtaining high-quality $MAPbI_3$ layers is the anti-solvent (AS) engineering, which consists of an one-step deposition of the $MAPbI_3$ film and dripping of the AS. The properties of the $MAPbI_3$ layer were found to be strongly influenced by the amount, dispensing speed, and spraying time of the AS solution. The $MAPbI_3$ solution was prepared by dissolving lead iodide and methyl-ammonium iodide in N,N-dimethylformamide and adding N,N-dimethyl sulfoxide. Diethyl ether (DE) was used for the AS solution. The results indicate that a $MAPbI_3$ layer appropriately sprayed with DE is beneficial for improving film quality and device efficiency because nucleation of $MAPbI_3$ layer is affected by the characteristics of DE, which affect the film's crystallinity, density, and surface morphology. The $MAPbI_3$ layer, which was optimized by using 0.7 mL of DE, a 3.03 mL/sec dispensing speed, and a 7 second time to spray after spinning showed the best efficiency of 13.74%, which was reproducible.

• Membrane Journal
• /
• v.32 no.2
• /
• pp.150-162
• /
• 2022

In the field of water treatment and pharmaceutical bio an alumina hollow fiber membrane used for mixture separation. However, due to the lack of strengths it is very brittle to handle and apply. Therefore, it is necessary to study and improve the bending strength of the membrane to 100 MPa or more. In this study, as the mixing ratio of the nano-particles increased to 0, 1, 3, and 5 wt%, the viscosity of the fluid mixture increased. The pore structure of the hollow membrane produced by interrupting the diffusion exchange rate of the solvent and non-solvent during the spinning process suppresses the formation of the finger-like structure and gradually increases the ratio of the sponge-like structure to improve the membrane mechanical strength to more than 100 MPa. As a result, an interparticle space was ensured to improve the porosity of the sponge-like structure with high permeability, and it showed excellent N2 permeability of about 100000 GPU and high water permeability of 3000 L/m² h. Therefore, it can be concluded, that the addition of γ-Al₂O₃ nanoparticles as sintering aid is an important method to enhance the mechanical strength of the α-alumina hollow fiber membrane to maintain high permeability.

• Korean Journal of Heritage: History & Science
• /
• v.52 no.4
• /
• pp.170-183
• /
• 2019

Fiber scutching refers to the process of extracting fibers from plants by separating or extracting fibers from the raw materials. As the definition of the term implies, the "Fiber Scutching" is performed on plants with advanced bast fiber as the primary material processing technique performed on plant materials. Some of the most popular phosphorus plants are ramie, hemp, flax, and the paper mulberry, which have a long history of cultivation and a wide range of distribution, making them very universal as a material supporting human life and culture. This study was described in Oju-yeonmunjangjeon-sango but was designed to re-examine the method of breaking dried stalks, which is currently unused in Korea, to examine the feasibility and characteristics of the technology. As a result of sampling and experimenting with hemp bast using the method recorded in the literature, hemp fiber was actually produced. The criteria for removing the shell from the hemp stem were the degree of discoloration and drying, and only when the stalk was completely discolored to yellow could segregation of the stalk from the shell be performed. The amount of sunlight and temperature were conditions that accelerated drying. However, if exposed for a long time, it is confirmed that hemp bast will be in a suitable condition to process, regardless of the amount of sunlight and temperature. 'Breaking of dried stalks', which utilizes the physical power of 'threshing with a flail' is considered a core process of the fiber scutching technique in 'Yukjin' in Hamgyeong-do. The bark and the core of the hemp were separated by tapping, the bast was thinly split, and the shell was peeled off, making it suitable for collecting with thread. The method of collecting the fibers by applying physical power causes downing on the fibers, which is to be generally avoided in the manufacture of bast fabric woven hemp or ramie. However, Hamgyeong-do's fiber scutching method seems to have applied this principle to the method of making fragile fabrics by using it in reverse. This method is distinct from the steaming or boiling of the stalks' in Andong, Korea, and it is similar to the Western method of spinning fabrics.

• Journal of the Korean Geographical Society
• /
• v.29 no.3
• /
• pp.318-339
• /
• 1994

U.S. had given large amount of cotton to Korea as food aid program since 1945. This cotton aid had negative impact on cotton culture in Korean agriculture. Korean government used counterparts funds (sale proceeds of food aid) not for investment to agriculture sector, but for military budgets. And food aid on program type had influenced general economic policies, which neglected agricultural sector too. Anti-agricultural policy which was helped by U.S. food aid, had caused cotton cultivator an economic loss. So this economic loss had made many farmers abandon cotton culture. But in our times, cotton is cultivated for the purpose of domestic consumption in a few rural villages. The purposes of this study are 1) to analyze the process of spatial reduction of cotton culture since 1945 in regional contexts in Korea, and 2) to identify the function and meaning of cotton culture which does not pay off in agricultural region. Materials for acreage of cotton culture are acquired through the agricultural statistical year book(1952-1989) and census. To clarify the meanings of cotton culture, field survey are conducted in a rural village which is identified as only one where cotton was cultivated in 1993. In these contexts, this study has come to the following conclusions. In the period of under the rule of Japanese Imperialism (1910-1945), G. arboreum, species of cotton which was traditionally cultivated since 1364, had been driven out. And G. hirustun species, which is suitable for the production of highly qualified textile, has been hierarchically diffused by policy. In these period, regional structure of Korean agriculture was reorganized for the provision with food to Japan. Crops leading this dependent spatial structure were rice and cotton. So agricultural region, specialized with cotton, were distributed in the hinterland of the area which is specialized with rice. U.S. cotton aid to Korea began in 1947. U.S. took an interest in agricultural export because of her domestic surplus of cotton. Cotton aid is one mechanism by which U.S government developed agricultural market in recipient countries, Specially in the exchange rates, up-valuation of won to the U.S. dollars made domestic cotton more expensive than cotton imported, Production cost of domestic cotton is higher than Government's purchasing price of cotton which was also more expensive than price of cotton imported. Korean farmer could not help abandoning the cultivation of cotton, and this gave rise to spatial reduction of cotton culture. Spatially, cotton culture was abandoned in early stage of reduction in regions where stand at a disadvantage climatically, and in next stage in regions where other up-land crops which paid off in urban market, eg, fruits, could be cultivated. In the stage of extinction, cotton was cultivated only in area where G. hirustun species was originated in Korean peninsula. This region is not only suitable climatically for cotton culture, but is far away from urban market. Use of cotton produced is not for spinning, but for fillings of comforter. The main purpose of cotton culture in rural village is not for cotton yields, but for increase of production of seasame, which is grown together with cotton as mixed crops. Cotton product are used for domestic consumption and sold out to gin house. Though cotton culture is not paid off, farmer wanted to cultivate continuously for the cultural purpose, and they wanted the cotton culture promotion policy with the goverment subsidy.