• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.74-74
• /
• 2009

카본나노튜브(CNT) 복합체는 우수한 기계적 성질을 가지고 있어 다양한 분야에서 연구되고 있다. 본 연구에서는 카본나노튜브(CNT)를 간단한 볼밀공정을 사용하여 Sn3.5Ag solder ball과 SAC305 powder 표면에 혼합하고 이를 통해 접합부 특성을 관찰하였다. 볼밀을 실시하기 전 카본나노튜브(CNT)는 초음파을 이용하여 분산을 실시하였다. Sn3.5Ag solder ball의 직경은 450um이고 SAC305 powder의 직경은 약 30um이었으며 이때 사용한 볼밀볼의 직경은 각각 3mm, 1mm이다. 볼밀 회전속도는 약 300rpm이고 6, 12, 18, 24시간동안 볼밀을 실시하였다. 24시간 볼밀 후에도 solder ball과 solder powder의 모양은 크게 변하지 않았다. SEM을 통해 표면을 관찰한 결과 분산된 카본나노튜브(CNT)는 solder ball과 solder powder의 표면에서 관찰되었다. 카본나노튜브(CNT)가 삽입된 solder ball은 BGA coupon 위에 놓고 Reflow를 실시하여 접합하였고 solder powder은 flux를 첨가하여 paste로 제조하여 2012 chip에 대한 접합특성을 관찰하였다. 카본나노튜브(CNT)는 solder ball 내부의 표면근처에서 관찰되었으며 카본나노튜브(CNT)가 혼합된 solder ball은 Aging 실시 후에 IMC 두께가 카본나노튜브(CNT)가 혼합되지 않은 solder ball에 비해 두께가 작고 접합강도는 약 10% 증가하였다. 또한 카본나노튜브(CNT)가 혼합된 solder paste와 카본나노튜브(CNT)가 혼합되지 않은 solder paste를 비교한 결과 인쇄성은 모두 양호하였으며 카본나노튜브(CNT)가 혼합된 paste를 사용한 chip의 전단강도가 높게 나타났다.

• 마이크로전자및패키징학회지
• /
• 제27권3호
• /
• pp.35-39
• /
• 2020

Nonwet (Head in Pillow) 불량은 SMT(surface mount technology) 공정 불량 유형 중 하나로 이 불량은 solder paste misalign, reflow 조건, package warpage, package ball size 등과 같은 인자에 따라 불량이 발생을 한다. 이에 본 논문은 Nonwet 발생 인자 중 ① reflow 조건 ② package ball & solder paste misalign ③ package ball 크기 type에 대한 인자를 선정하여 nonwet 실험을 진행하였다. 먼저 reflow 조건의 경우 soldering 시간이 길 경우 nonwet risk가 증가를 하나, reflow 공정에 N₂를 적용할 시 solder ball 산화 억제에 따른 nonwet 개선을 확인 할 수 있었다. 또한 package ball과 solder paste misalign 발생 시 ball과 paste의 접촉 깊이가 20 ㎛ 이하의 경우 nonwet에 취약 했으며, package ball 체면적이 작을수록 nonwet 관점 개선됨을 확인 할 수 있었다.

• 한국공작기계학회논문집
• /
• 제16권6호
• /
• pp.159-162
• /
• 2007

Recently, Pb-free solder ball technology, which is getting more significant in miniaturization of electronic equipment, and resolution of recent environmental problems, is necessary to be developed. A plastic-core solder ball is much promising in those considerations. Plastic-core solder balls have the tendency to replace the usual metal-core solder ball from low material cost and superior mechanical properties. The thermal effects, however, are important in manufacturing process, such as deposing micro-sized metal thin film on the spherical polymer surface. Furthermore plastic-core solder balls are easy to be broken due to CTE and elastic coefficient of material property from heat transfer. We propose technical computational investigations for the manufacturing design and the reliability of plastic-core solder ball from thermal stress analysis.

• 한국안전학회지
• /
• 제25권6호
• /
• pp.14-21
• /
• 2010

A miniature single solder ball joint is designed to mimic the actual solder joints used in the micro-electric industries. Shear tests were conducted to evaluate the mechanical behavior of miniature single solder joints at intermediate strain rates from $0.019\;s^{-1}$ to $2.16\;s^{-1}$ at room temperature. The shear fracture strength of the present solder ball joints generally increased with increasing shear strain rate, ranging from 32 to 51MPa. This behavior is affected by the sensitivity of bulk solder strength to strain rate. Shear fracture mode changed from brittle to partial ductile (failure inside the bulk solder) with an increase of shear speed. The unloading shear fracture toughness is generally consistent with the measure of the amount of bulk solder on the fractured surface.

• 마이크로전자및패키징학회지
• /
• 제16권2호
• /
• pp.11-19
• /
• 2009

모아레 간섭계를 이용하여 와이어 본딩 플라스틱 볼 그리드 (WB-PBGA) 패키지의 열-기계적인 거동 특성을 연구하였다. 실시간 모아레 간섭계를 이용하여 각 온도단계 에서 변위분포를 나타내는 간섭무늬를 각각 얻고, 그로부터 굽힘변형 거동 및 솔더볼의 변형률에 대한 해석을 비교하여 수행하였다. 본 실험에서는 full grid와 perimeter with central connections 및 perimeter의 배열 형태를 갖는 세 가지 패키지를 사용하였으며, 이 배열 형태를 비교하여 굽힘변형 및 솔더볼의 평균변형률을 자세하게 해석하였다. 솔더볼의 유효변형률은 WB-PBGA-FG의 경우 칩 가장자리 바로 바깥쪽 솔더볼에서, WB-PBGA-P/C의 경우 가운데 연결 솔더볼의 가장 바깥 솔더볼에서, WB-PBGA-P의 경우는 칩과 가장 기까운 안쪽 솔더볼에서 최대값을 가지는 것으로 나타났다.

• Journal of Welding and Joining
• /
• 제29권1호
• /
• pp.99-106
• /
• 2011

Joint strength between a solder ball and a pad on a substrate is one of the major factors which have effects on electronic device reliability. The effort to improve solder joint strength via surface cleaning, heat treatment and solder composition change have been in progress. This paper will discuss the method of solder ball joint strength improvement using LF hydrogen radical cleaning treatment and focus on the effects of surface treatment condition on the solder ball shear strength and interfacial reactions. In the joint without radical cleaning, voids were observed at the interface. However, the specimens cleaned by hydrogen-radical didn't have voids at the interface regardless of cleaning time. The shear strength between the solder ball and the pad was increased over 120%(about 800gf) when compared to that without the radical treatment (680gf) under the same reflow condition. Especially, at the specimen treated for 5minutes, ball shear strength was considerably increased over 150%(1150gf). Through the observation of fracture surface and cross-section microstructure, the increase of joint strength resulted from the change of fracture mode, that is, from the solder ball fracture to IMC/Ni(P) interfacial fracture. The other cases like radical treated specimen for 1, 3, 7, 9min. showed IMC/solder interfacial fracture rather than fracture in the solder ball.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.873-878
• /
• 2000

Semiconductor packaging technology is changed rapidly according to the trends of the micro miniaturization of multimedia and information equipment. For I/O limitation and fine pitch limitation, DIP and SOP/QFP are replaced by BGA/CSP. This is one of the surface mount technology(SMT). Solder ball is bumped n the die pad and connected onto mounting board. In ball bump formation, vacuum suction type ball alignment process is widely used, However this type has some problems such as ionization, static electricity and difficulty of fifo(first-input first-out) of solder balls. Seesaw type is reducing these problems and has a structural simplicity and economic efficiency. Ball cartridge velocity and ball aligned plate angle are Important variables to improve the ball alignment Process. In this paper, seesaw-type CSP solder ball loader is developed and the optimal velocity and plate angle are proposed.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2007년도 SMT/PCB 기술세미나
• /
• pp.67-79
• /
• 2007

• 한국전기전자재료학회논문지
• /
• 제17권6호
• /
• pp.575-579
• /
• 2004

Package reliability test was conducted to investigate the effect of solder paste composition at BGA Package. It was found that the shape and size of the phase form are affected by the processing parameters. The material have used to fill in the via was Sn/36Pb/2Ag and Sn/0.75Cu type solder paste. Sn/36Pb/2Ag and Sn/0.75Cu paste were fabricated on Tape-BGA substrates by screen printing process, and via ball mount data were characterized with variations of dwell time of 85 seconds at reflow peak temperature at 22$0^{\circ}C$ or 24$0^{\circ}C$. The test condition was MRT 30 $^{\circ}C$/60 %RH/96 HR. Failures formed of a ball-off in solder paste process were observed by using a Optical Microscope and SEM(Scanning Electron Microscope). It was concluded that intermetallic layer growth played important roles in increasing solder fatigue strength for addition of Ag composition. The degradation of shear strength of solder composition is discussed.

• Journal of Welding and Joining
• /
• 제19권3호
• /
• pp.311-316
• /
• 2001

This paper presents that the affecting factors to the solderability and initial reliability. It is the factor that the coefficient of thermal expansion between package and PCB(Printed Circuit Board), the quantity of solder paste and reflow condition, and Au thickness of the solder ball pad on polyimide tape. As the reflow soldering condition for 48 ${\mu}BGA$ is changed, it is estimated that the quantity of Au diffusion at eutectic Sn-Pb solder surface and initial bonding strength of eutectic Sn-Pb solder and lead free solder. It is the result that quantitative measurement of Au diffusion quantity is difficult, but the shear strength of eutectic Sn-Pb solder joint is 842 mN at first reflow and increases 879 mN at third reflow. The major failure mode in solder is judged solder fracture. So, Au diffusion quantity is more affected by reflow temperature than by the reflow times.