• Journal of Sensor Science and Technology
• /
• v.19 no.3
• /
• pp.197-201
• /
• 2010

This paper describes the fabrication and characteristics of a NO sensor using ZnO thin film integrated 3C-SiC micro heater based on polycrystalline 3C-SiC thin film of operation in harsh environments. The sensitivity, response time, and operating properties in high temperature and voltages of NO sensors based SiC MEMS are measured and analyzed. The sensitivity of device with pure ZnO thin film at the heater operating power of 13.5 mW ($300^{\circ}C$) is 0.875 in NO gas concentration of 0.046 ppm. In the case of Pt doping, the sensitivity of at power consumption of 5.9 mW ($250^{\circ}C$) was 1.92 at same gas flow rate. The ZnO with doped Pt was showed higher sensitivity, lower working temperature and faster adsorption characteristics to NO gas than pure ZnO thin film. The NO gas sensor integrated SiC micro heater is more strength than others in high voltage and temperature environments.

• Journal of Sensor Science and Technology
• /
• v.18 no.4
• /
• pp.307-310
• /
• 2009

This paper describes the formation of porous 3C-SiC by anodization. 3C-SiC thin films were deposited on p-type Si(100) substrates by APCVD using HMDS(Hexamethyildisilane: $Si_2(CH_3)_6$). UV-LED(380 nm) was used as a light source. The surface morphology was observed by SEM and the pore size was increased with increase of current density. Pore diameter of 70 $\sim$ 90 nm was achieved at 7.1 mA/cm$^2$ current density and 90 sec anodization time. FT-IR was conducted for chemical bonding of thin film and porous 3C-SiC. The Si-H bonding was observed in porous 3C-SiC around wavenumber 2100 cm$^{-1}$. PL shows the band gap enegry of thin film(2.5 eV) and porous 3C-SiC(2.7 eV).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.185-185
• /
• 2009

The aligned liquid crystals (LCs) display on SiNx thin films using ion-beam (IB) irradiation was studied with controllability ofpretilt angle depending on incident energies of the IB. Plasma-enhanced chemical vapor deposition (PECVD) was used to orient the LCs on SiNx alignment films. The LCs alignment property for the SiNx thin films were observed to verify the practical application potential (figure1). A good LCs alignment of vertical alignment LCs cells on SiNx thin film surfaces irradiated with incident IB energy of 1800eV was achieved. Also, a good LC alignment by the IB irradiation on the SiNx thin film surface was observed at an annealing temperature of $180^{\circ}C$. However, the alignment defects of the nematic liquid crystal was observed at an annealing temperature above $230^{\circ}C$. The atomic force microscopy (AFM) images of LCs on SiNx thin film surfaces irradiated with IB energy was used for the surface analysis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.311-312
• /
• 2006

We studied homeotropic alignment effect for a nematic liquid crystal (NLC) on the $SiO_x$, thin film irradiated by the new ion beam method $SiO_x$ thin films were deposited by plasma enhanced chemical vapor deposition (PECVD) and were treated by the DuoPIGatron ion source. A uniform liquid crystal alignment effect was achieved over 2100 eV ion beam energy. Tilt angle were about $90^{\circ}$ and were not affected by various ion beam energy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.225-225
• /
• 2010

In this study, the optimum structure of a magnetic thin film inductor was designed for application of DC-DC converters. The $Ni_{81}Fe_{19}$ (at%) alloy was selected as a high-frequency($\geq$ MHz) magnetic thin film core material and deposited on various substrates (bare Si, $SiO_2$ coated Si) using a high vacuum RF magnetron sputtering system. As-deposited NiFe thin films show similar magnetic properties compared to bulk NiFe alloys, indicating that they have a good film quality. The optimum design of solenoid-type magnetic thin film inductors was performed utilizing a Maxwell computer simulator (Ansoft HFSS V7.0 for PC) and parameters obtained from the magnetic properties of magnetic core materials selected. The high-frequency characteristics of the inductance(L) and quality factor(Q) obtained for the designed inductors through simulation agreed well with those obtained by theoretical calculations, confirming that the simulated result is realistic. The optimum structure of high-performance ($Q{\geq}60$, $L\;=\;1{\mu}H$, efficiency${\geq}90%$), high-frequency (${\geq}5MHz$), and solenoid-type magnetic thin film inductors was designed successfully.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.1057-1059
• /
• 2002

ZnO-Si-ZnO multi-layer thin films have been deposited by pulsed laser deposition (PLD). And then, the films have been annealed at $300^{\circ}C$ in oxygen ambient pressure. Electrical properties of the films were improved slightly than ZnO thin film without Si layer. Also, the optical and structural properties changed by Si layer in ZnO thin film. The optical and structural properties of Si-doped ZnO thin films were characterized by PL(Photoluminescence) and XRD(X-ray diffraction method) respectively. Electrical properties were measured by van der Pauw Hall measurements.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.1
• /
• pp.26-35
• /
• 2024

Aluminum-induced crystallization (AIC) as a route to reduce the fabrication cost and to obtain polycrystalline Si (p-Si) thin-film of large grain size is a promising alternative of single-crystalline (s-Si) substrate or p-Si thin-film obtained by conventional methods such as solid phase crystallization (SPC) and laser-induced crystallization (LIC). As the AIC process occurs at the interface between a-Si and Al thin-films, there are various process and interface parameters. Also, it directly means that there is a certain parametric window to obtain p-Si of large grain size having uniform crystal orientation. In this article, we investigate the effect of the various process and interface parameters to obtain p-Si of large grain size and uniform crystal orientation from the literature review. We also suggest the potential use of the p-Si as a virtual substrate for the growth of various compound semiconductors in a form of low-dimension as well as thin-film as a way for their monolithic integration on Si.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.11a
• /
• pp.55-59
• /
• 1993

In this study, we developed new process for doping poly-Si film. Sb(antimony) thin film was used as doping source. Sb was evaporated on poly-Si film deposited by LPCVD fallowed by annealing. We investigate sheet resistance variation with annealing temperature and time. Finally we adapted this process to poly-Si TFT fabrication.

• 전기의세계
• /
• v.25 no.1
• /
• pp.104-107
• /
• 1976

The switching characteristics of Non-crystalline As-Te-Si-Ge thin film device using Ag, In and Al metal for electrode, has been investigated. Threshold voltage and holding current of each sandwich type device varied due the to formation of the potential barrier in between non crystalline solid and electrode interface.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.5
• /
• pp.197-199
• /
• 2011

In this paper, the bottom-gate thin-film transistors (TFTs) were fabricated with an amorphous/microcrystalline Si double layer (DL) as an active layer and the variations of the electrical characteristics were investigated according to the DC bias stresses. Since the fabrication process of DL TFTs was identical to that of the conventional amorphous Si (a-Si) TFTs, it creates no additional manufacturing cost. Moreover, the amorphous/microcrystalline Si DL could possibly improve stability and mass production efficiency. Although the field effect mobility of the typical DL TFTs is similar to that of a-Si TFTs, the DL TFTs had a higher reliability with respect to the direct current (DC) bias stresses.