• Journal of the Mineralogical Society of Korea
• /
• v.26 no.2
• /
• pp.119-127
• /
• 2013

Borosilicate glass dissolution is an important chemical process that impacts the glass durability as nuclear waste form that may be used for high-level radioactive waste disposal. Experiments reported that the glass dissolution rates are strongly dependent on the bulk composition. Because some relationship exists between glass composition and molecular-structure distribution (e.g., non-bridging oxygen content of $SiO_4$ unit and averaged coordination number of B), the composition-dependent dissolution rates are attributed to the bulk structural changes corresponding to the compositional variation. We examined Na borosilicate glass structures by performing classical molecular dynamics (MD) simulations for four different chemical compositions ($xNa_2O{\cdot}B_2O_3{\cdot}ySiO_2$). Our MD simulations demonstrate that glass surfaces have significantly different chemical compositions and structures from the bulk glasses. Because glass surfaces forming an interface with solution are most likely the first dissolution-reaction occurring areas, the current MD result simply that composition-dependent glass dissolution behaviors should be understood by surface structural change upon the chemical composition change.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.2
• /
• pp.269-278
• /
• 2022

Utilization of high-voltage electrolyte additive(s) at a small fraction is a cost-effective strategy for a good solid electrolyte interphase (SEI) formation and performance improvement of a lithium-rich layered oxide-based high-energy lithium-ion cell by avoiding the occurrence of metal-dissolution that is one of the failure modes. To mitigate metal-dissolution, we explored fluorinated dual-additives of fluoroethylene carbonate (FEC) and di(2,2,2-trifluoroethyl)carbonate (DFDEC) for building-up of a good SEI in a 4.7 V full-cell that consists of high-capacity silicon-graphite composite (15 wt% Si/C/CF/C-graphite) anode and Li_1.13Mn_0.463Ni_0.203Co_0.203O₂ (LMNC) cathode. The full-cell including optimum fractions of dual-additives shows increased capacity to 228 mAhg^-1 at 0.2C and improved performance from the one in the base electrolyte. Surface analysis results find that the SEI stabilization of LMNC cathode induced by dual-additives leads to a suppression of soluble Mn²⁺-O formation at cathode surface, mitigating metal-dissolution event and crack formation as well as structural degradation. The SEI and structure of Si/C/CF/C-graphite anode is also stabilized by the effects of dual-additives, contributing to performance improvement. The data give insight into a basic understanding of cathode-electrolyte and anode-electrolyte interfacial processes and cathode-anode interaction that are critical factors affecting full-cell performance.

• The Journal of Engineering Geology
• /
• v.25 no.1
• /
• pp.1-8
• /
• 2015

Deep geological disposal is the preferred storage method for high-level radioactive waste, because it ensures stable long-term storage with minimal potential for human disruption. Because of the risk of groundwater contamination, a buffer of steel and bentonite layers has been proposed to prevent the leaching of radionuclides into groundwater. Quartz is one of the most common minerals in earth's crust. To understand how deformation and dissolution phenomena affect waste disposal, here we study quartz samples at pressure, temperature, and pH conditions typical of deep geological disposal sites. We perform a dissolution experiment for single quartz crystals under different pressure and temperature conditions. Solution samples are collected and the dissolution rate is calculated by analyzing Si concentrations in a solution excited by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). After completing the dissolution experiment, deformation of the quartz sample surfaces is investigated with a confocal laser scanning microscope (CLSM). An empirical formula is introduced that describes the relationship between dissolution rate, pressure, and temperature. These results suggest that bentonite layers in engineering barrier systems may be vulnerable to thermal deformation, even when exposed to higher temperatures on relatively short timescales.

• Journal of the Mineralogical Society of Korea
• /
• v.9 no.1
• /
• pp.1-6
• /
• 1996

Woolastonite from Susan occurs as intercalations in limestone beds of Lower Paleozoic Joseon Supergroup. It is a thermal metamorphic product of impure limestone. Electron microprobe analysis shows that it is considerably pure wollastonite. It has triclinic cell with a=7.932$\AA$, b=7.328$\AA$, c=7.069$\AA$, $\alpha$=89.995$^{\circ}$, $\beta$=$95.255^{\circ}$, and $ \Upsilon=103.367^{\circ}$.Dissolution behaviors of wollastonite have been studied conducting three different dissolution experiments; two different reactions with HC1 (one batch and one re-initialization experiment) and one traction with distilled water. In the batch type powder wollastonite-HCl reaction, pH of solution rapidly increases in the early stage and then its rate of increase slows down to reach plateau resulting in parabolic relationship with time. It is represented by the early rapid rise and fall in pH giving a sharp pH-edge and succeeding slow rise in the re-initialization experiment. The early rapid rise in pH is due to the rapid sorption of H- in solution to oxygens on the reactive surface of wollastonite and the fall in pH means that all reactive surface sites are occupied by H- ions and no more H- adsorption occurs. The slow rise in pH following the pH- edge is due to the dissolution of wollastonite as evidenced by the correlation of pH variation and cation concentration. Dissolution of powder wollastonite in HCl shows linear trend with time. Si is dissolved predominantly over Ca at a constant rate. Ca is dissolved predominantly in the very early stage. Dissolution rate of coarse-grained wollastonite fragments in distilled water is parabolic with times howing a rapid reaction in the early stage and a slow reaction in the advanced stage. The Ca/Si ratio in solution is high in the case of coarse-grained wollastonite fragment as compared with powder wollastonite. The coarse-grained wollastonite fragment-water (acid) reaction resulted in the solution with an elevated constant pH value (alkaline) giving an important significance on the environmental view point.

• Resources Recycling
• /
• v.18 no.6
• /
• pp.38-45
• /
• 2009

Dissolution characteristics of magnesite ore in hydrochloric acid solution and removal of impurity were investigated. The dissolution yield increased with increasing temperature and with decreasing particle size. The optimum conditions for dissolution were found to be reaction period of 120 min, reaction temperature of $80^{\circ}C$ and mean particle size of 100. Under optimal dissolution condition the extraction of Mg was 98%. It was found that most of Si and Al exist in the residue, and they can be removed by filtering. Dissolved impurity ions were precipitated as metal hydroxides by pH adjustment. Polymers were used as coagulants for metal hydroxides and the suitable coagulant dosage was 1mg/100ml of non-ionic polymer.

• Applied Microscopy
• /
• v.8 no.1
• /
• pp.77-79
• /
• 1978

Al-Si junctions were made by vacuum deposition of aluminium on to silicon wafers and examined by TEM. The uneven interfaces of the junctions are formed due to the surface tension of the molten solution resulting in preferential dissolution of silicon in aluminium at some areas. These undesirable uneven interfaces affect the junction shape and so the over-all characteristics of the devices.

• Corrosion Science and Technology
• /
• v.23 no.2
• /
• pp.83-92
• /
• 2024

A hot-dip simulator was utilized to replicate abnormal coating buildup observed during line stops at galvanize lines, assessing the influence of processing conditions on buildup (up to 14 mm/side). Steel samples from 19 coils (comprising IF, BH, LCAK, HSLA, DP600-DP1180, Si: 0.006 - 0.8 wt%, P: 0.009 - 0.045 wt%) were examined to explore the phenomenon of heavy coating growth. It was discovered that heavy coating buildup (~3 mm/h) and rapid strip dissolution (~0.17 mm/h) in a GA or GI pot can manifest with specific combinations of steel chemistry and processing conditions. The results reveal the formation of a unique coating microstructure, characterized by a blend of bulky Zeta crystals and free Zn pockets/networks due to the "Sandlin" growth mechanism. Key variables contributing to abnormal coating growth include steel Si content, anneal temperature, dew point in heating and soaking furnaces, Zn pot temperature, Zn bath Al%, and cold-rolling reduction%. At ArcelorMittal Dofasco galvanize lines, an automatic online warning system for operators and special scheduling for incoming Si-bearing steels have been implemented, effectively preventing further heavy buildup occurrences.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.4
• /
• pp.340-347
• /
• 2008

Dissolution process of serpentine in distilled water was systematically investigated for study on pre-treatment of serpentine which was a candidate material for carbon dioxide sequestration. The metallic ions(Ca, Si, Mg etc.) were dissolved in distilled water at ambient condition and their concentrations were changed with dissolution time. The precise evaluation of dissolution process for serpentine dissolved solvent was performed by ion conductivity and pH measurement. Serpentine dissolution in distilled water was evaluated as a stable pre-treatment process without changes of crystallographic structure and chemical structure changes.

• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.350-356
• /
• 2013

Dissolution of ferronickel slag depending on aging condition was studied. Ferronickel slag typically contains 54.05% $SiO_2$, 34.33% MgO, and 5.51% $Fe_2O_3$. The main structure composite was similar to Enstatite [(Mg, $Fe^{2+}$ )$SiO_3$]. Ferronickel slag aging was made in 3 months under various experimental conditions, in water, bubbling water and wetting air. The most effective aging condition was the wetting air treatment. In this condition, the dissolving concentration of Mg and Fe was 80.0% and 75.1% respectively. The XRD and SEM data revealed that the wetting air condition also showed the biggest structural damage.

• Resources Recycling
• /
• v.24 no.1
• /
• pp.3-11
• /
• 2015

Soluble silica generated from acid leaching process is very difficult to filter and deceases the purity of products, and thus becomes one of hot issues in hydrometallurgy. This paper reviewed the dissolution and reactivities of silicates in acid solution, and the methods for treatment of soluble silica. Removal of silica with alkaline pre-treatment, crystallization to $SiO_2$ and precipitation behaviour of silica with coagulation under acid conditions were briefly described.