• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.3
• /
• pp.380-386
• /
• 2016

This paper presents a compact and low-power on-chip touch sensor and readout circuit using shunt proximity touch sensor and its design scheme. In the proposed touch sensor readout circuit, the touch panel condition depending on the proximity of the finger is directly converted into the corresponding voltage level without additional signal conditioning procedures. Furthermore, the additional circuitry including the comparator and the flip-flop does not consume any static current, which leads to a low-power design scheme. A new prototype touch sensor readout integrated circuit was fabricated using complementally metal oxide silicon (CMOS) $0.18{\mu}m$ technology with core area of $0.032mm^2$ and total current of $125{\mu}A$. Our measurement result shows that an actual 10.4 inches capacitive type touch screen panel (TSP) can detect the finger size from 0 to 1.52 mm, sharply.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.3
• /
• pp.352-358
• /
• 2016

A 5-phase phase-locked loop (PLL) for USB2.0 applications was implemented by using an all-synthesis technique. The length of the time-to-digital converter for the fine phase detector was halved by the operation of a coarse phase detector that uses 5-phase clocks. The maximum time difference between the rising edges of two adjacent-phase clocks was 6 ps at 480 MHz. The PLL chip in a 65-nm process occupies $0.038mm^2$, consumes 4.8 mW at 1.2 V. The measured rms and peak-to-peak output jitters are 8.6 ps and 45 ps, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.3
• /
• pp.287-292
• /
• 2016

A multiphase clock and data recovery (CDR) circuit having a novel rotational bang-bang phase detector (RBBPD) is demonstrated. The proposed 1/4-rate RBBPD decides the locking point using a single clock phase among sequentially rotating 4 clock phases. With this, our RBBPD has significantly reduced power consumption and chip area. A prototype 10-Gb/s 1/4-rate CDR with RBBPD is successfully realized in 65-nm CMOS technology. The CDR consumes 5.5 mW from 1-V supply and the clock signal recovered from $2^{31}-1$ PRBS input data has 0.011-UI rms jitter.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.706-711
• /
• 2014

A low power 6-bit flash ADC that uses an input voltage range detection algorithm is described. An input voltage level detector circuit has been designed to overcome the disadvantages of the flash ADC which consume most of the dynamic power dissipation due to comparators array. In this work, four digital input voltage range detectors are employed and each input voltage range detector generates the specific clock signal only if the input voltage falls between two adjacent reference voltages applied to the detector. The specific clock signal generated by the detector is applied to turn the corresponding latched comparators on and the rest of the comparators off. This ADC consumes 68.82 mW with a single power supply of 1.2V and achieves 4.3 effective number of bits for input frequency up to 1 MHz at 500 MS/s. Therefore it results in 4.6 pJ/step of Figure of Merit (FoM). The chip is fabricated in 0.13-um CMOS process.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.789-796
• /
• 2014

A CMOS photo detection bias quenching circuit is developed to be used with single photon avalanche photodiodes (SPADs) operating in Geiger mode for the detection of weak optical signals. The proposed bias quenching circuits for the performance improvement reduce the circuit size as well as improve the performance of the quenching operation. They are fabricated in a $0.18-{\mu}m$ standard CMOS technology to verify the effectiveness of this technique with the chip area of only $300{\mu}m^2$, which is about 60 % of the previous reported circuit. Two types of proposed circuits with resistive and capacitive load demonstrated improved performance of reduced quenching time. With a commercial APD by HAMAMATSU, the dead time can be adjusted as small as 50 ns.

• Journal of Industrial Technology
• /
• v.32 no.A
• /
• pp.103-107
• /
• 2012

Due to improvement of the semiconductor technology, the LED replaces the conventional lighting source and LED drivers have been studied and developed. The LED is driven by the constant current control method according to its characteristics. For the constant current control method, the linear regulator and the switching regulator is used. The switching regulator is usually used to LED drivers because it has specific characteristics as the wide input dynamic range and the high efficiency. In this paper, we have described the principle and the implement of the switching regulator, using the drive IC and the low cost DSP chip. Also, both methods have been implemented and its electrical characteristics had almost same experimental results in the steady state and the transient state.

• Journal of Power Electronics
• /
• v.2 no.1
• /
• pp.67-75
• /
• 2002

This paper presents the control algorithm for maximum efficiency drives of an induction motor system with the high dynamic performance. This system uses a simple model of the induction motor that includes equations of the iron losses. The model, which only requires the parameters of the induction motor, is referred to a field-oriented frame. The minimum point of the input power can be obtained at the steady state condition. The proposed optimal efficiency control algorithm calculates the reference torque and flux currents for the vector control of the induction motors. A 32 bit floating point TMS320C32 DSP chip implements the drive system with the efficiency optimization controller. The results show the effectiveness of the control strategy Proposed for the induction motor drive.

• ETRI Journal
• /
• v.36 no.4
• /
• pp.635-642
• /
• 2014

Three-dimensional integrated circuits (3D ICs) implement heterogeneous systems in the same platform by stacking several planar chips vertically with through-silicon via (TSV) technology. 3D ICs have some advantages, including shorter interconnect lengths, higher integration density, and improved performance. Thermal-aware design would enhance the reliability and performance of the interconnects and devices. In this paper, we propose thermal-aware floorplanning with min-cut die partitioning for 3D ICs. The proposed min-cut die partition methodology minimizes the number of connections between partitions based on the min-cut theorem and minimizes the number of TSVs by considering a complementary set from the set of connections between two partitions when assigning the partitions to dies. Also, thermal-aware floorplanning methodology ensures a more even power distribution in the dies and reduces the peak temperature of the chip. The simulation results show that the proposed methodologies reduced the number of TSVs and the peak temperature effectively while also reducing the run-time.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.8
• /
• pp.62-71
• /
• 1994

A novel semiconductor device is proposed to be used as a processing element for the implementation of pulse-mode neural networks which consists of alternating n' GaAs quantum wells and undoped AlGaAs barriers sandwitched between n' GaAs cathode and P' GaAs anode and in simple circuit in conjunction with a parallel capacitive and resistive load the trigger circuit generates neuron-like pulse train output mimicking the function of axon hillock of biological neuron. It showed the sigmoidal relationship between the frequency of the pulse-train and the applied input DC voltage. In conjunction with MQWIMD the various neural circuits are proposed especially a neural chip monolithically integrated with photodetectors in order to perfrom the pattern recognition.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.1
• /
• pp.124-130
• /
• 2014

In highly reliable and durable systems, failures due to aging might result in catastrophes. Aging monitoring techniques to prevent catastrophes by predicting such a failure are required. This paper presents a scan-based on-line aging monitoring scheme which monitors aging during normal operation and gives an alarm if aging is detected so that the system users take action before a failure occurs. We illustrate our modified scan chain architecture and aging monitoring control method. Experimental results show our simulation results to verify the functions of the proposed scheme.