• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1158-1160
• /
• 2004

In this paper, a PWM SEPIC AC-AC converter for VVCF applications such as AC line conditioner, phase shifter is presented. The PWM SEPIC AC-AC converter is modelled by using complex circuit DQ transformation whereby the characteristics equations such as voltage gain and input power factor is analytically obtained. Finally, the PSIM simulation shows the validity of the modelling and analysis.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.49-52
• /
• 2007

In this paper, we proposed a design photovoltaic generation systems with SEPIC-Flyback converter. The SEPIC-Flyback converter is operated to SEPIC converter the state turn-on of the switch and the state turn-off the switch is operated Flyback converter. Therefore application rate of the core increases and voltage stress of switch and transformer decreases with active clamp operation. Also we performed MPPT(Maximum Power Point Tracking) control for efficient working of Photovoltaic Dower generation system.

• Journal of Power Electronics
• /
• v.15 no.1
• /
• pp.39-53
• /
• 2015

This paper presents the regulation of the output voltage and inductor currents in a Single Ended Primary Inductor Converter (SEPIC), operating in the continuous conduction mode (CCM) using a sliding mode controller. Owing to the time varying nature of the SEPIC converter, designing a feedback controller is a challenging task. In order to improve the dynamic performance of the SEPIC, a Sliding Mode Controller (SMC) is developed. The developed SMC is designed by using a state space average model. The performance of the developed controller with the SEPIC converter is validated at different working conditions through Matlab simulations. It is also compared with the performance while using a PI controller. The results show that the designed controller gives very good output voltage regulation under different operating conditions such as a varying input voltage, changes in the load and component variations. A 48V, 46W experimental setup for has been developed in an analog platform to validate the performance of the proposed SMC.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.165-166
• /
• 2015

본 논문은 새로운 단일전력변환 SEPIC(Single-Ended Primary-Inductor Converter)-ZETA 절연형 양방향 컨버터를 제안한다. 제안된 컨버터는 SEPIC과 ZETA 컨버터가 결합된 구조로 절연을 통해 안정성을 강화했고, DC측 리플 전류가 낮아 에너지 저장장치의 수명을 연장시킨다. 그리고 SEPIC 컨버터 모드(DC/AC)와 ZETA 컨버터 모드(AC/DC)에서의 입출력 전압비가 동일해 양방향 제어 알고리즘이 간단하다. 또한, 기존 two-stage 구성의 양방향 컨버터와 달리 회로가 단순하며, 단일전력변환을 통한 고효율 저비용의 장점을 가지고 있다. 본 논문에서는 이론적 해석 및 제안한 컨버터의 250W급 시작품을 이용한 실험결과를 통해 컨버터의 우수성 및 성능을 검증한다.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.143-149
• /
• 2016

The two-stage converter is widely used in traditional DC/AC inverter. It has several disadvantages such as complex topology, large volume and high loss. In order to overcome these shortcomings, a novel half load-cycle worked dual SEPIC single-stage inverter, which is based on the analysis of the relationship between input and output voltages of SEPIC converters operating in the discontinuous conduction mode (DCM), is presented in this paper. The traditional single-stage inverter has remarkable advantages in small and medium power applications, but it can’t realize boost DC/AC output directly. Besides one pre-boost DC/DC converter is needed between the DC source and the traditional single-stage inverter. A novel DC/AC inverter without pre-boost DC/DC converter, which is comprised of two SEPIC converters, is studied. The output of dual SEPIC converters is connected with anti-parallel and half load-cycle control is used to realize boost and buck DC/AC output directly and work properly, whatever the DC input voltage is higher or lower than the AC output voltage. The working principle, parameter selection and the control strategy of the inverters are analyzed in this paper. Simulation and experiment results verify the feasibility of the new inverter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.3
• /
• pp.258-265
• /
• 2006

In this paper, an active clamping sepic-flyback converter has been proposed, which is suitable for a fuel cell based power generation system. The proposed converter is superposition of sepic converter mode and flyback mode. It has outstanding high boosting output voltage, component utilization and high efficiency characteristics under the inherently severe low output voltage of the fuel cell generator. In this paper, the validity of the proposed converter has been verified by the informative simulation and experimental results that make used of the PEMFC.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.1
• /
• pp.39-44
• /
• 2003

As the portable electronic equipments are developed and popularized, the batteies are more important. To prolong life of the equipments, engineers demand to have batteries of high-power density and they are used to use Li-ion batteries popularly Li-ion batteries are better than conventional batteries, Ni-cd, about power density per volume and weight, but they have a fault that discharge voltage of them goes down. In order to maximize life of the Li-ion batterries, we have to use a converter which is suitable for the characteristic of Li-ion batteries. Therefore, capacitive idling SEPIC(Single Ended Primary Inductance Converter) that is derived from the SEPIC topology is proposed as a source of the Portable low-power applications. The converter has characteristics of buck-boost porformance. Besides, that makes it possible to increase the switching frequency by partial soft commutation of power switches through adding a diode and a switch. This paper is presented the characteristics, DC voltage conversion ratio, circuits of operation modes, of the converter and it is analized and implemented.

• Journal of Power Electronics
• /
• v.11 no.5
• /
• pp.743-750
• /
• 2011

This article deals with the sensor-less control of a DC Motor via a SEPIC Converter-Full Bridge combination powered through solar panels. We simultaneously regulate, both, the output voltage of the SEPIC-converter to a value larger than the solar panel output voltage, and the shaft angular velocity, in any of the turning senses, so that it tracks a pre-specified constant reference. The main result of our proposed control scheme is an efficient linear controller obtained via Lyapunov. This controller is based on measurements of the converter currents and voltages, and the DC motor armature current. The control law is derived using an exact stabilization error dynamics model, from which a static linear passive feedback control law is derived. All values of the constant references are parameterized in terms of the equilibrium point of the multivariable system: the SEPIC converter desired output voltage, the solar panel output voltage at its Maximun Power Point (MPP), and the DC motor desired constant angular velocity. The switched control realization of the designed average continuous feedback control law is accomplished by means of a, discrete-valued, Pulse Width Modulation (PWM). Experimental results are presented demonstrating the viability of our proposal.

• Journal of Power Electronics
• /
• v.4 no.3
• /
• pp.152-160
• /
• 2004

This paper presents analysis, modeling, and design of a low-harmonic, isolated, active-clamped SEPIC for future avionics applications. Simpler converter dynamics, high switching frequency, zero voltage-Transition-PWM switching, and a single-layer transformer construction result. This paper describes complete design of a digital controller for a high-frequency switching power supply. Guidelines for the minimum required resolution of the analog-to-digital converter, the pulse-width modulator, and the fixed-point computational unit is derived. A design example based on a SEPIC converter operating at the high switching frequency is presented. The controller design is based on direct digital design approach and standard root-locus techniques.

• Proceedings of the KIPE Conference
• /
• 2007.11a
• /
• pp.187-189
• /
• 2007

본 논문에서는 연료전지 발전시스템을 제안하였다. 제안된 시스템에서 DC-DC 컨버터는 인덕터 에너지 저장형인 Flyback 컨버터와 커패시터 에너지 저장형인 SEPIC 컨버터를 변압기를 이용하여 2차측 출력을 결합한 SEPIC-Flyback 컨버터로 스위치의 온 오프시 모두 승압이 가능하여 저전압/대전류의 특징을 갖는 연료전지 시스템에 적합하다. 이를 계통연계형 인버터 시스템에 적용하여 최적화된 연료전지 발전시스템을 제안하였다.