• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1608-1615
• /
• 2010

In this paper, we proposed the method called "DoublePico"(Double Piconet) forovercoming low data transmission rate in a scatternet. This needs a new Ad-hoc network topology to transmit with high rate. Every node performs the function of the relay station. DoublePico has two bluetooth devices that should form two different poconets; every node can make a link between two different piconets. Two different piconets are linked in one node by the link with two bluetooth divices thereby forming the Ad-Hoc network. In this paper, we shows the method of DoublePico which supports about 457kbps of the maximum data transmission rate. This method supports a higher data transmission rate than the traditional bluetooth's Ad-Hoc topology by using analysis and comparison of existing algorithm of bluetooth specification and simulation results. Specifically, this paper focuses on the impact of intererence on the PER (Packet Error Rate), throughput performance, and the throughput improvement with SAW(Stop and Wait)-ARQ scheme in DoublePico.

• Archives of Plastic Surgery
• /
• v.50 no.3
• /
• pp.248-253
• /
• 2023

Metal fixation systems for cranial bone flaps cut by a drill are convenient devices for cranioplasty, but cause several complications. We use modified craniotomy using a fine diamond-coated threadwire saw (diamond T-saw) to reduce the bone defect, and osteoplasty calcium phosphate cement without metal fixation. We report our outcomes and tips of this method. A total of 78 consecutive patients underwent elective frontotemporal craniotomy for clipping of unruptured intracranial aneurysms between 2015 and 2019. The follow-up periods ranged from 13 to 66 months. The bone fixation state was evaluated by bone computed tomography (CT) and three-dimensional CT (3D-CT). The diamond T-saw could minimize the bone defect. Only one wound infection occurred within 1 week postoperatively, and no late infection. No pain, palpable/cosmetically noticeable displacement of the bone flap, fluid accumulations, or other complications were observed. The condition of bone fixation and the cosmetic efficacy were thoroughly satisfactory for all patients, and bone CT and 3D-CT demonstrated that good bone fusion. No complication typical of metal fixation occurred. Our method is technically easy and safety, and achieved good mid-term bone flap fixation in the mid-term course, so has potential for bone fixation without the use of metal plates.

• The Journal of the Acoustical Society of Korea
• /
• v.15 no.4E
• /
• pp.14-20
• /
• 1996

The double mode SAW resonator filters have the serious shortcoming that out-of-band rejection above the passband is quite poor. Hence a new structure of the double mode filter is designed with the COM (Coupling Of MOdes) theory with better out-of-band rejection characteristics while keeping all the beauties of the conventional type. The second goal of the design is to reduce the planar size of the structure so that mass productivity of low frequency devices can be improved. For those purposes, several IDT's and relfector gratings are added to or subtracted from the conventional structure so that the modification can lead to better overall performance as a filter. As results of the investigation, several new double mode SAW resonator filter structures are developed. A new structure shows 10dB more out-of-band rejection that the conventional type with 25% reduced device size. Good agreement is demonstrated between the analytical results and experimental results for an illustrative 325MHz four pole resonator filter on 64°YX LiNbO3.

• Korean Journal of Crystallography
• /
• v.2 no.2
• /
• pp.32-40
• /
• 1991

The effects of compositional variation, rotation speel and pulling rate on the growth of optical quality Bi120e02(1 crystals were examined. It was found to flatten the shape of crystal-melt interface for yowing a single crystals less than about 30mm in diameter at the rotation speed of 50rpm. Diameter of crystals with flat interface was increased as the pulling rate. The precipitation of Bi40e3012 phase set limits to pulling rate of BGO crystals. Precipitate-free BGO crystals were grown under pulling rate of 2mm l hr which released the stress resulted from too hi어 Pulling rate, and from 6. IBi203·GeO2 batch composition obtained by addition of 0.1 mole Bi203 into Bi-deficient melts to fill up the deficiency resulted from gradual volatilization of Bi2O). The pale-yellow colored crystals had good quality in that dislocation density was less than 103pits/cm, and it also exhibited transmittance of 70% and optical activity of 23°/mm. and SAW velosity was measured 1700m/sec on 111 cut 110 propagating BGO crystals. The SAW filter with electrode thickness of 9.8um was fabricated by using the electron beam and dry etching technique, it makes Bi12GeO20 devices intersting for color TV IF with half device size.

• The Journal of the Acoustical Society of Korea
• /
• v.13 no.1E
• /
• pp.45-54
• /
• 1994

Characteristics of a piezoelectric material are evaluated to pick up the optimal crystal cut and propagation direction for a SAW device. For the piezoelectric single crystal $LiTaO_4$, such items are investigated as the Rayleigh wave velocity, the electromechanical coupling factor, the surface permittivity, the frequency-temperature coefficient, the air loading attenuation, the pure mode propagation, the beam steering and the misalignment sensitivity. Theoretical calculations reveal that Y-cut and Z-propagation is the optimal SAW propagation path. The results are confirmed through experiments. The method empolyed in this paper is applicable to other crystals, too, either single or poly crystals.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1488-1490
• /
• 2000

ZnO:Cu thin films are deposited by using an RF magnetron co-sputtering system with Cu chips attached on ZnO target. Structural and electrical properties are analyzed as a function of deposition conditions, such as Cu chip areas, $O_2/(Ar+O_2)$ ratios, and working pressures, The results show that a higher electrical resistivity above $10^{10}$ ${\Omega}cm$ along with an excellent c-axial growth can be easily achieved by Cu-doping. SAW filters based on the ZnO:Cu films are also fabricated to estimate the electric-mechanical coupling coefficient($K^{2}_{eff}$). Higher $K^{2}_{eff}$ and lower insertion losses are observed for ZnO:Cu films, compared with those for ZnO films.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.6
• /
• pp.534-549
• /
• 2009

As the thin film technology has emerged in various fields, adhesion of the film interface becomes an important issue in terms of the longevity and durability of thin film devices. Diverse nondestructive methods utilizing acoustic techniques have been developed to assess the interfacial integrity. As an effective technique based on the ultrasonic wave focusing and the surface acoustic wave(SAW) generation, scanning acoustic microscopy(SAM) has been investigated for adhesion evaluation. Visualization of film microstructures and quantification of adhesion weakness levels by SAW dispersion are the recent achievements of SAM. To overcome the limitations in the theoretical dispersion model only suitable for perfectly elastic and isotropic materials, a new model has been more recently developed in consideration of film anisotropy and viscoelasticity and applied to the adhesion evaluation of polymeric films fabricated on semiconductive wafers.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.9 s.240
• /
• pp.1276-1281
• /
• 2005

Compound semiconductors are the semiconductors composed of more than two chemical elements. Lithium Tantalate$K_I$ wafer is used for several optical devices, especially surface acoustic wave(SAW) device. Because of the lithography in SAW device process, $LiTaO_3$ polishing is needed. In this paper, the commercial slurries $(NALC02371^{TM},\; ILD1300^{TM},\;ceria slurry)$ used for chemical mechanical polishing(CMP) were tested, and the most suitable slurry was selected by measuring material removal rate and average centerline roughness$(R_a)$. From these result, it was proven that $ILD1300^{TM}$ was the most suitable slurry for $LiTaO_3$ wafer CMP due to the chemical reaction between solution in slurry and material.

• Proceedings of the KIEE Conference
• /
• 2007.10a
• /
• pp.393-394
• /
• 2007

In this study, to minimize the above effect Zinc Oxide(ZnO) thin films on Si(100) substrate were deposited by RF magnetron sputter with changing sputtering conditions such as Ar/$O_2$ gas ratios, RF power, substrate temperature, chamber prsssure and target-substrate distance. To analyze a crystallographic properties of the films, ${\Theta}/2{\Theta}$ mode X-ray diffraction, rocking curve and Alpha-step were performed. SAW filters were fabricated to evaluate the feasibility of ZnO thin film as a piezoelectrical materials and the processes of ZnO SAW filters using etch and lift-off were compared.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.5
• /
• pp.69-75
• /
• 2001

In this paper, a fast and easy impedance matching method, which could give the impedance matching component for the general 1 or 2-port network was introduced. First, the entire network structure was defined which consists of the network part to be matched and the impedance matching part composed of inductors and capacitors. Next, the transmission matrix and input and output impedances of the entire network from the terminal impedance conditions were calculated, then the exact solutions for the matching components were obtained. To verify the efficiency of this method, this method was applied to the CDMA If band withdrawal weighted SAW transversal filter, and investigated the effects of the impedance matching before and after, through the simulation and experiment. As the result, the performance of a fractional bandwidth of 1.2%, insertion loss of 29 dB, and VSWR of 80 have improved to a factional bandwidth of 1.8％, insertion loss of 9 dB, VSWR of 3 at 85.38 MHz center frequency. The result shows that this impedance matching method could be used in the SAW devices and other types of 1 or 2-port network.