• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.639-642
• /
• 2005

A new dual-slope ramp (DSR) reset waveform is proposed to improve the dark room contrast ratio in AC-PDPs. The proposed reset waveform has two different voltage slopes during a ramp-up period. The first voltage slope is lower than the conventional ramp voltage slope, causing a reduction in the background luminance, whereas the second voltage slope is higher than the conventional ramp voltage slope, causing an increase in the background luminance. Thus, a bias voltage is also applied during the second voltage-slope period to adjust the background luminance and address discharge characteristics. As a result, the proposed dual-slope reset waveform can lower the background luminance, thereby improving the high dark room contrast ratio of an AC-PDP without reducing the address voltage margin

• 대한인간공학회지
• /
• 제29권4호
• /
• pp.681-686
• /
• 2010

Although the height of a ramp is an important design element, it has not been considered in prior studies. Therefore, in this study, the ramp slope and height are considered as independent variables. To analyze the effects of the slope and height, five levels of slope (1:6, 1:8, 1:10, 1:12 and 1:14) and three levels of height (15cm, 30cm and 45cm) are considered. For the dependent variables, the total time, velocity and perceived discomfort were considered as usability measures, pulse rate changes and EMG signals of four related muscles (extensor carpi radialis, triceps brachii, anterior deltoid and posterior deltoid) were considered as physiology measures. As a result, differences among usability and physiological characteristic for the five slopes increased as the height increased. Additionally, slope effects were minor when the height was low (15cm). Almost domestic/international regulations and guidelines related to ramp recommended 1:12 slope for the ramp design, however, there was no significant difference between 1:10 and 1:12 according to result of this study. In addition, slope effects were minor at a low height; thus, a slope of 1:8 can be recommended if the installation space for a gentler ramp is not sufficient.

• Journal of Biosystems Engineering
• /
• 제26권6호
• /
• pp.517-524
• /
• 2001

Steep and narrow ramp installed in the paddy field makes it difficult and sometimes dangerous to drive agricultural machines on it. Because agricultural machinery become larger and heavier, it is necessary to revise design standard for ramp to provide safe travel. This study was conducted to revise the design standard fur paddy field ramp, especially for its width and slope. A mathematical model predicting travelling path of a tractor on paddy field ramp and farm road was developed and simulated. To verify this model, field tests were carried out. The model could predict trvelling path with RMS Error of 12.5cm and 8.2cm, which were judged to be adoptable fur determining the width of paddy field ramp. By applying this model to 110ps tractor, which was assumed to be the largest tractor in Korea, width of paddy field ramp was determined as over 3.6m. The slope of paddy field ramp, which provided tractor with 10% of the total weight of the tractor and the mounted implement as reaction force at front wheel against ground was analyzed by considering weight transfer effect on a ramp. The result showed that adequate slope of paddy field ramp was 14°.

• 의료ㆍ복지 건축 : 한국의료복지건축학회 논문집
• /
• 제26권2호
• /
• pp.31-38
• /
• 2020

Purpose: The ramp is an important facility for the barrier free access and vertical circulation of users of various buildings, including users of walker, wheelchair users, stroller users, and baggage carriers. The installation standards for ramps in Korea have various problems during construction and BF certification. It is necessary to improve the criteria for ensuring practical mobility and safety. Method: Korean standard, International Standard(ISO 21542, 2011), German Standard(DIN 18040-1, 2010), Austrian Standard(OENORM B 1600, 2017), Swiss Standard(Norm SIA 500, 2009), Canadian Standard(Building Standards Guide, 2017), American Standard(ADA Standards, 2010) were investigated and analyzed. A comprehensive improvement of the ramp installation standards is proposed. Results: The ramp is a necessary facility for the barrier free access and vertical circulation of the disabled. It shall be installed with comprehensive consideration of the appropriate slope of the ramp, the distance of the continuous slope, the handle and upstand for pedestrian safety. In order to improve convenience, setting the proper slope and limiting the length of the slope are very important, and improvements are required to the levels presented by international and foreign standards. The unclear standards of Korean law and BF certification standards should be clearly improved so as not to be misinterpreted in construction and Barrier Free Certification. Implication: International and foreign standards should be reviewed to ensure practical mobility and safety. And comprehensive improvement measures should be presented through continuous research.

• 한국소음진동공학회논문집
• /
• 제15권11호
• /
• pp.1248-1254
• /
• 2005

L/UL(Load/unload) mechanism has been widely used in SFF(Small form factor) HDD because L/UL technology has many advantages such as an increase of areal density, reduction of power consumption and improvement of shock resistance. In this system, the most important design goal is no slider-disk contact and fast air-hearing breaking during L/UL process. To do so, we should consider many design parameters related to L/UL system. The ramp shape is the most dominant component among parameters which dramatically affect the L/UL performance. This paper makes an advanced ramp model using ANSYS/LS-DYNA. Through this FE model, this paper investigates the effect of initial ramp slope and location of air-bearing breaking. From the experiment for three different ramps, we also verify that experimental results agree with simulation results. We conclude that the ramp design should have small ramp slope at the moment which a suspension tap contacts with ramp and large ramp slope after air-bearing breaking in order to improve L/UL Performance.

• 대한전자공학회논문지SD
• /
• 제43권1호
• /
• pp.59-64
• /
• 2006

단일 기울기 ADC에 사용되는 램프 신호의 기울기는 공정과 주파수 변화에 민감하다. 이러한 변화는 ADC 이득 변화와 이미지 신호 프로세싱의 성능까지 영향을 준다. 본 논문에서는 자동 교정된 램프 신호를 이용한 단일 기울기 ADC를 이용하여 공정과 주파수 변화에 영향을 받지 않은 CMOS 이미지 센서를 제안하다. 본 논문에서 제안된 built-in-self-calibration (BISC) 구조는 공정과 주파수 변화에 상관없이 입력 조도별로 일정한 출력 값을 갖는 단일 기울기 ADC 동작을 가능하게 한다. 제안된 BISC를 탑재한 CMOS 이미지 센서는 $0.35{\mu}m$ 공정을 이용하여 제작하였다. 측정 결과는 제안된 구조가 공정이나 클럭 주파수의 변화에 따라 효과적으로 램프 기울기를 교정한다는 것을 보여준다. 칩 면적의 증가 정도는 $0.7\%$ 미미하였다.

• International journal of advanced smart convergence
• /
• 제10권1호
• /
• pp.184-196
• /
• 2021

This study, in order to evaluate the safety of evacuation by comparing and analyzing the RSET according to the slope change of the ramp, which is a vertical evacuation route in case of fire in a high school building, Evacuation simulation was run the Pathfinder program changed the slope of the ramp to 10°, 15°, and 20° for each male students and female students. In the case of female students, it was analyzed that when the final RSET slope was 15°, 25.7 seconds were shorter than when 10°, and 4.2 seconds were shorter than when 20°. Male students also found that when the final RSET slope was 15°, 23.8 seconds were shorter than when 10°, and 5.4 seconds shorter than when 20°. It was analyzed that even if the number of participants was increased and the evacuation simulation was executed, the safety of evacuation could be improved when the slope of the slope is 15° as the RSET when the slope of the slope is 15° is shorter than that of 10° and 20°.

• 반도체디스플레이기술학회지
• /
• 제5권2호
• /
• pp.11-14
• /
• 2006

A new reset waveform with negative ramp pulse is proposed. Conventional reset waveform applied to the commercial PDP uses a positive ramp pulse. The reset waveforms, especially focused on ramp area, were examined with 2 dimensional fluid code. The proposed negative reset waveform showed much lower ignition voltage ($\sim$70V) as compared with the conventional reset waveform. When the negative ramp pulse was applied, all of the positive-charged ions are collected on the scan electrode. It is found that the ignition voltage of reset discharge due to the negative ramp pulse became lower than that of positive ramp discharge.

• Safety and Health at Work
• /
• 제11권3호
• /
• pp.307-313
• /
• 2020

Background: Many tasks in industrial and health care setting are involved with pushing and pulling tasks up or down on a ramp. An efficient method of moving cart which reduces the risk of low back pain should be concerned. This study aimed to investigate the effects of handling types (HTs) and slope on lumbar spinal load during moving a cart on a ramp. We conducted a 2 × 2 × 4 factorial design with three main factors: 2 HTs, 2 handling directions of moving a cart and 4 degrees of ramp slope. Methods: Thirty healthy male workers performed 14 tasks consist of moving a cart up and down on the ramp of 0°, 10°, 15°, and 20° degrees with pushing and pulling methods. Joint angles from a 3D motion capture system combined with subject height, body weight, and hand forces were used to calculate the spinal load by the 3DSSPP program. Results: Our results showed significant effect of HT, handling directions and slope on compression and shear force of the lumbar spine (p < 0.001). When the ramp gradient increased, the L4/5 compression forces increased in both pushing and pulling (p < 0.001) Shear forces increased in pulling and decreased in pushing in all tasks. At high slopes, pulling generated more compression and shear forces than that of pushing (p < 0.01). Conclusion: Using the appropriate technique of moving a cart on the ramp can reduce the risk of high spinal load, and the pushing is therefore recommended for moving a cart up/down on ramp gradients.

• 전력전자학회논문지
• /
• 제10권6호
• /
• pp.587-591
• /
• 2005

AC PDP의 구동파형은 Reset 구간에서 명암비를 높이고 화질향상을 위해서 전압파형을 서서히 증가시키고 또 감소시키는데, 이 전압파형의 기울기와 크기가 온도와 더불어서 PDP의 화질과 관련이 있다. 그래서 본 논문에서는 Reset 구간에서 Y 전극에 인가하는 램프파형의 setup 및 setdown 구간에서의 기울기와 -Vy전압을 온도에 따라서 가변함으로써, 주위의 온도가 상온에서 저온이나 고온으로 변화하여도 PDP의 화질이 영향을 받지 않고 최상으로 유지하게 하는 온도 적응형 RESET 파형 발생회로를 제안하였다.