• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.418-419
• /
• 2006

We investigate the influence of the ambient gas during thermal annealing on the photoluminescence (PL) properties of europium-silicate thin films. The films were fabricated on substrates by using a radio-frequency magnetron sputtering method and subsequent rapid thermal annealing (RTA). The mechanism for the formation of the europium silicates during the annealing process was investigated by using X-ray diffraction (XRD) spectroscopy, Auger electron spectroscopy (AES) and transmission electron microscopy (TEM). A series of narrow PL spectra from $Eu^{3+}$ ions was observed from the film annealed in $O_2$ ambient. Broad PL spectra associated with $Eu^{2+}$ ions, with a maximum intensity at 600 nm and a FWHM of 110 nm, were observed from the thin film annealed at $1000^{\circ}C$ in $N_2$ ambient.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.288-291
• /
• 2002

Application of metal silicides such as TiSi$_2$ and CoSi$_2$ as contacts and gate electrodes are being studied. However, TiSi$_2$ due to the linewidth-dependance, and CoSi$_2$ due to the excessive Si consumption during silicidation cannot be applied to the deep-submicron MOSFET device. NiSi shows no such problems and can be formed at the low temperature. But, NiSi shows thermal instability. In this investigation, NiSi was formed with a Ti-capping layer to improve the thermal stability. Ni and Ti films were deposited by the thermal evaporator. The samples were then annealed in the N$_2$ ambient at 300-800$^{\circ}C$ in a RTA (rapid thermal annealing) system. Four point probe, FESEM, and AES were used to study the thermal properties of Ti-capped NiSi layers. The Ti-capped NiSi was stable up to 700$^{\circ}C$ for 100 sec. RTA, while the uncapped NiSi layers showed high sheet resistance after 600$^{\circ}C$. The AES results revealed that the Ni diffusion further into the Si substrate was retarded by the capping layer, resulting in the suppression of agglomeration of NiSi films.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.835-838
• /
• 1992

The $TiN/TiSi_2$ bilayer has been studied for contact barrier layer at ULSI recently. The $TiN/TiSi_2$ bilayer was formed by RTA in $NH_3$ ambient simultaneously after the Ti film was deposited on silicon substrate. In this paper, properties of $TiN/TiSi_2$ bilayer was evaluated according to $BF_2$ dopant concentration and dopant redistribution in $TiN/TiSi_2$ bilayer was also analyzed. In this experiment, the composition and structure of $TiN/TiSi_2$ bilayer were constant even though dopant concentration increased but silicide growth rate decreased. Boron atoms were redistributed within TiN film and at $TiSi_2Si$ interface during the bilayer formation.

• 한국재료학회지
• /
• 제13권7호
• /
• pp.460-464
• /
• 2003

Ni and Ti films were deposited by the thermal evaporator, and then annealed in the N$_2$ ambient at 300-80$0^{\circ}C$ in a RTA(rapid thermal annealing) system. Four point probe, AEM, FESEM, AES, and XPS were used to study the effects of Ti-capping layers on the thermal stability of NiSi thin films. The Ti-capped NiSi was stable up to $700^{\circ}C$ for 100 sec. RTA, while the uncapped NiSi layers showed high sheet resistance after $600^{\circ}C$. These results were due to that the Ni in-diffusion and Si out-diffusion were retarded by the capping layer, resulting in the suppression of the formation of NiSi$_2$and Si grains at the surface.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.35-35
• /
• 2009

Capacitorless one transistor dynamic random access memory (1T-DRAM) cells were fabricated on the fully depleted strained-silicon-on-insulator (FD sSOI) and the effects of silicon back interface state on buried oxide (BOX) layer on the memory properties were evaluated. As a result, the fabricated 1T-DRAM cells showed superior electrical characteristics and a large sensing current margin (${\Delta}I_s$) between "1" state and "0" state. The back interface of SOI based capacitorless 1T-DRAM memory cell plays an important role on the memory performance. As the back interface properties were degraded by increase rapid thermal annealing (RTA) process, the performance of 1T-DRAM was also degraded. On the other hand, the properties of back interface and the performance of 1T-DRAM were considerably improved by post RTA annealing process at $450^{\circ}C$ for 30 min in a 2% $H_2/N_2$ ambient.

• 한국세라믹학회지
• /
• 제33권9호
• /
• pp.1012-1018
• /
• 1996

To investigate the final structures and reactions of silicides a somewhat thick Ti monolayer Co monolayer and Co/Ti bilayer films were deposited on single Si(100) wafer by electron beam evaporation followed by heat treatment using RTA system in N2 ambient. TiO2 film formed between Ti and TiSi2 layers due to oxgen or moisture in the Ti monolayer sample. The final layer structure obtained after the silicidation heat-treatment of the Co/Ti bilayer sample turned out to be TiSi2/CoSi2/Ti-Co-Si alloy/CoSi2/Si sbustrate. This implies that imperfect layer inversion occurred due to the formation of Ti-Co-Si intermediate phase.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1270-1271
• /
• 2008

Effects of thin ZnO/Mg interlayers on electrical and optical properties between p-GaN and ITO were characterized for its application to GaN-LEDs. The ZnO and Mg layers were deposited to have various thicknesses (1${\sim}$6nm for ZnO and 1${\sim}$2nm for Mg) by sputtering. After RTA process, the atomic migration between Mg and ZnO and the formation of Ga vacancy were observed from SIMS depth profile, resulting in the increase of hole concentration and the reduction of band bending at the surface region of p-GaN. The sample using ZnO(2nm)/Mg(2nm) interlayer produced the lowest contact resistance with SBH(Schottky barrier height) of 0.576 eV and the transmittance higher than 83% at a wavelength of 460nm when annealed at 500$^{\circ}C$ for 3min in air ambient.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.42.2-42.2
• /
• 2010

Transparent conducting oxides (TCOs) are of significant importance for their applications in various devices, such as light-emitting diodes, thin-film solar cells, organic light-emitting diodes, liquid crystal displays, and so on. In order for TCOs to contribute to the performance improvement of these devices, TCOs should have high transmittance and good electrical properties simultaneously. Sn-doped $In_2O_3$ (ITO) is the most commonly used TCO. However, indium is toxic and scarce in nature. Thus, ZnO has attracted a lot of attention because of the possibility for replacing ITO. In particular, group III impurity-doped ZnO showed the optoelectronic properties comparable to those of ITO electrodes. Al-doped ZnO exhibited the best performance among various doped ZnO films because of the high substitutional doping efficiency. However, in order for the Al-doped ZnO to replace ITO in electronic devices, their electrical and optical properties should further significantly be improved. In this connection, different ways such as a variation of deposition conditions, different deposition techniques, and post-deposition annealing processes have been investigated so far. Among the deposition methods, RF magnetron sputtering has been extensively used because of the easiness in controlling deposition parameters and its fast deposition rate. In addition, when combined with post-deposition annealing in a reducing ambient, the optoelectronic properties of Al-doped ZnO films were found to be further improved. In this presentation, we deposited Al-doped ZnO (ZnO:$Al_2O_3$ = 98:2 wt%) thin films on the glass and sapphire substrates using RF magnetron sputtering as a function of substrate temperature. In addition, the ZnO samples were annealed in different conditions, e.g., rapid thermal annealing (RTA) at $900^{\circ}C$ in $N_2$ ambient for 1 min, tube-furnace annealing at $500^{\circ}C$ in $N_2:H_2$=9:1 gas flow for 1 hour, or RTA combined with tube-furnace annealing. It is found that the mobilities and carrier concentrations of the samples are dependent on growth temperature followed by one of three subsequent post-deposition annealing conditions.

• 전자공학회논문지A
• /
• 제33A권11호
• /
• pp.105-111
• /
• 1996

We have invetigated the characteristics of thermal instability of Co-silicides annealed at 850$^{\circ}$C ~ 1000$^{\circ}$C for 10~90 minutes in a furance with N$_{2}$ ambient. In our experiments, Co-silicides and Co/Ti bilayer silicides were formed by depositing (Co, Ti) films on the clean Si substrates in an E-beam evaporator and performing the RTA annelaing. The sheet resistances of Co-silicides formed form Co exhibited the nearly constant value under the post-annealing time above 900$^{\circ}$C showing the increase of 30% and 60% under the conditions annealed at 900$^{\circ}$C and 1000$^{\circ}$C for 30minutes. On the other hand, there were no remarkable changes in the sheet resistance sof Co-silicides formed form Co/Ti bilayer under the post-annealing conditons below 1000$^{\circ}$C.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.209-209
• /
• 2009

Fabrication of p-type ZnO has already proven difficult and usually inconsistent despite numerous worldwide efforts. Many research groups studied electrical and optical properties P, Li, As, N single doped ZnO thin film. In P-doped ZnO thin film, the reproducibility of p-type conduction with $P_2O_5$ as a dopant source was shown to be relatively poor. In this study, we made P single doped and Li & P co-doped ZnO target. To investigate electrical and optical properties of P single doped and Li & P co-doped ZnO thin film using $P_2O_5$ and $Li_3PO_4$ dopant source respectively was deposited by PLD. The growth temperature was changed 500, $700^{\circ}C$ and various oxygen partial pressure and post-annealing conditions was changed temperature, different gas ambient($O_2,N_2$). We investigate that how to change electrical and optical properties as function of growth temperature, oxygen partial pressure and post-annealing(RTA).