• Korean Journal of Materials Research
• /
• v.14 no.10
• /
• pp.683-687
• /
• 2004

The BON thin films were grown on the Si substrate by the RF-PECVD method. When stored at the room temperature, the phase separation or transition of BON thin films occurred on the surface, due to the hydrophilic property of BON. The oxidation of BON thin films occurred mainly by the evaporation of B, O and N. The oxidized BON thin films consisted of an amorphous phase and a bit of the polycrystalline phase.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.773-780
• /
• 1996

Silicon oxide films were prepared by using five kinds of organosilicon compound as gas sources without oxygen by rf plasma-enhanced CVD (PECVD). UV light was irradiated on a substrate vertically during deposition to enhance film oxidation and ablation of carbon contamination in a deposited films. Films prepared with UV irradiation contained less carbon than those prepared without UV irradiation. The oxidation of the films was improved by UN irradiation. The effect of UV irradiation was, however, not observed when the films were prepared with tetramethy lsilane (TMS) which contained no oxygen atom. Dissociated oxygen atoms from an organosilicon compound were excited in the plasma with UV irradiation around the substrate surface and affected the enhancement of film oxidation and ablation of carbon in the films.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.04a
• /
• pp.73-73
• /
• 2007

Amorphous BON and Si-DLC thin films were synthesized by the RF plasma enhanced CVD method, and their oxidation behavior was studied up to $500^{\circ}C$ in air. The oxidation of both films was accompanied by evaporation of volatile species. The oxidation of BON film was preceded by nitrogen escape from the film, and oxygen penetration into the film. The oxidation of Si-DLC film was preceded by carbon escape probably as CO or $CO_2$from the film, and oxygen penetration into the film. The inwardly transported oxygen simply stayed in the oxidized BON and Si-DLC thin films.

• Journal of Powder Materials
• /
• v.26 no.4
• /
• pp.305-310
• /
• 2019

In the present work, spheroidization of angular vanadium powders using a radio frequency (RF) thermal plasma process is investigated. Initially, angular vanadium powders are spheroidized successfully at an average particle size of $100{\mu}m$ using the RF-plasma process. It is difficult to avoid oxide layer formation on the surface of vanadium powder during the RF-plasma process. Titanium/vanadium/stainless steel functionally graded materials are manufactured with vanadium as the interlayer. Vanadium intermediate layers are deposited using both angular and spheroidized vanadium powders. Then, 17-4PH stainless steel is successfully deposited on the vanadium interlayer made from the angular powder. However, on the surface of the vanadium interlayer made from the spheroidized powder, delamination of 17-4PH occurs during deposition. The main cause of this phenomenon is presumed to be the high thickness of the vanadium interlayer and the relatively high level of surface oxidation of the interlayer.

• Korean Chemical Engineering Research
• /
• v.46 no.2
• /
• pp.408-413
• /
• 2008

In this work, the use of LPRTO (low pressure rapid thermal oxidation) and remote plasma oxidation was evaluated for the preparation of ultra thin silicon oxide layer with less than 5 nm. The silicon oxide thickness grown by LPRTO was rapidly increased and saturated. The maximum thickness could be controlled at about 5 nm. As RF power and oxygen flow rate at a remote plasma oxidation increased, the behavior of oxide growth was almost the same as that of LPRTO. The oxide thickness of 4 nm was the maximum obtained by a remote plasma oxidation in this work. The quality of silicon oxide grown by LPRTO was comparable to the thermally grown conventional oxide.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.9
• /
• pp.45-51
• /
• 2014

This work carried out for the effective synthesis characteristics of graphene nanowall film by controlling the electric field in a RF plasma CVD process. For that, the bipolar bias voltage was applied to the substrate such as Si and glass materials for the best chemical reaction of positive and negative charges existing in the plasma. For supplying the seed formation sites on substrate and removing the oxidation layer on the substrate surface, the electron bombardment into substrates was performed by a positive few voltage in hydrogen plasma. After that, hydrocarbon film, which is not a graphene nanowall, was deposited on substrates under a negative bias voltage with hydrogen and methane gases. At this step, the film on substrates could not easily identify due to its transparent characteristics. However, the transparent film was easily changed into graphene nanowall by the final hydrogen plasma treatment process. The resultant raman spectra shows the existence of significant large 2D peaks corresponding to the graphene.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.3
• /
• pp.51-57
• /
• 2019

To protect the Cu surface from oxidation in air, a two-step plasma process using Ar and $N_2$ gases was studied to form a copper nitride passivation as an anti-oxidant layer. The Ar plasma removes contaminants on the Cu surface and it activates the surface to facilitate the reaction of copper and nitrogen atoms in the next $N_2$ plasma process. This study investigated the effect of Ar plasma on the formation of copper nitride passivation on Cu surface during the two-step plasma process through the full factorial design of experiment (DOE) method. According to XPS analysis, when using low RF power and pressure in the Ar plasma process, the peak area of copper oxides decreased while the peak area of copper nitrides increased. The main effect of copper nitride formation in Ar plasma process was RF power, and there was little interaction between plasma process parameters.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.11
• /
• pp.934-940
• /
• 2001

Magnetic properties were investigated for Si/SiO$_2$/NiFe(300 )/A1$_2$O$_3$(t)/Co(200 ) junction related with the parameters of $Al_2$O$_3$. Insulating $Al_2$O$_3$ layer was formed by depositing a 5~40 thick Al layer, followed by a 90~120s RF plasma oxidation in an $O_2$ atmosphere. Magnetoresistance was not observed for tunnel junction with 5~10 thick Al layer, but magnetoresistance was observed large for tunnel junction with 15~40 thick Al layer. Oxidation time did not largely influence magnetoresistance. Tunnel magnetoresistance effect depended on magnetization behavior of two ferromagnetic layers. Tunneling junction was confirmed through nonlinear I-V curve. In this work, tunneling magnetoresistance(TMR) up to 30 % was observed. This apparent TMR is an artifact of the nonuniform current flow over the junction in the cross geometry of the electrodes.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.2
• /
• pp.397-400
• /
• 2010

Zirconium oxide thin films deposited on the p-type Si(100) substrates by radio-frequency (RF) reactive magnetron sputtering with different plasma gas ratios have been studied by using spectroscopic ellipsometry (SE), atomic force microscopy (AFM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The deposition of the films was monitored by the oxygen gas ratio which has been increased from 0 to 80%. We found that the thickness and roughness of the zirconium oxide thin films are relatively constant. The XRD revealed that the deposited thin films have polycrystalline phases, Zr(101) and monoclinic $ZrO_2$ ($\bar{1}31$). The XPS result showed that the oxidation states of zirconium suboxides were changed to zirconia form with increasing $O_2$ gas ratio.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.2
• /
• pp.331-334
• /
• 2010

In the present study, carbon supports mixed with purified multi-walled carbon nanotubes (MWNTs) and carbon blacks (CBs) were used to improve the cell performance of direct methanol fuel cells (DMFCs). Additionally, the effect of $O_2$ plasma treatment on CBs/MWNTs supports was investigated for different plasma RF powers of 100, 200, and 300 W. The surface and structural properties of the CBs/MWNTs supports were characterized by FT-IR, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and inductive coupled plasma-mass spectrometer (ICP-MS). The electrocatalytic activity of PtRu/CBs/MWNTs catalysts was investigated by cyclic voltammetry measurement. In the experimental results, the oxygen functional groups of the supports were increased with increasing plasma RF power, while the average Pt particle size was decreased owing to the improvement of dispersibility of the catalysts. The electrochemical activity of the catalysts for methanol oxidation was gradually improved by the larger available active surface area, itself due to the introduction of oxygen functional groups. Consequently, it was found that $O_2$ plasma treatments could influence the surface properties of the carbon supports, resulting in enhanced electrocatalytic activity of the catalysts for DMFCs.