• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.262-267
• /
• 2003

The heteroepitaxial ZnO thin film on sapphire (0001) substrate was prepared by an off-axis Radio Frequency(RF) magnetron sputtering. The crystallinity of ZnO thin film was affected by deposition pressure, RF power, and substrate temperature. High quality heteroepitaxial ZnO thin film was obtained when the kinetic energy of sputtered particles is well harmonized with the surface mobility. In the result of Photoluminescence(PL) of heteroepitaxial ZnO thin film, Ultraviolet(UV) emissions at 3.36 and 3.28 eV were observed at low(17 K) and Room Temperature(RT). respectively. As the ZnO thin film was annealed in O$_2$ambient, the crystallinity was improved while UV emission was drastically decreased.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1574-1579
• /
• 2016

This paper presents a self-powered sensor-node scheme using a RF wireless power harvesting techniques for improve drone time of flight. Sensor-node that is proposed is turned when two conditions satisfy: The one is input RF ID data from master-node should be same with sensor-node's ID, and the other one is RF wireless power harvesting system is turned on by hysteresis switch. In this paper, master-node's output is 26 dBm at 263 MHz. Maximum RF to DC power conversion efficiency is about 55% at 4-6 dBm input power condition (2 meter from master-node). The maximum RF wireless power harvesting range is about 13 meter form master-node. And power consumption of the sensor-node's load elements such as transmitter, MCU and temperature sensors is approximately average 15 mA at 5.0 V for 10 msec.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.86-86
• /
• 2011

RF magnetron sputtering을 이용하여 RF파워 변화에 따라 GZO 박막을 제작하였다. 박막제작은 유리기판 위에 하였고, 전기적, 광학적 특성을 조사하였다. 박막의 증착시 초기 압력은 $2.0{\times}10^{-6}Torr$, 증착온도는 상온으로 고정하여 증착하였으며, 기판은 Corning 1737 유리 기판을 사용하였다. RF 파워 공정변수는 20W, 50W, 80W, 110W로 변화를 시켰다. 유리기판에 증착된 모든 GZO박막은 200 nm의 두께로 증착되었으며 모든 GZO 박막에서 85% 이상의 투과율을 나타내었다. RF파워가 낮을수록 투과율을 증가하였으며, 광학적 밴드갭 또한 증가하였다. 공정별로 제작된 모든 GZO박막에서 (002)면의 배향성이 관찰되었고, RF파워가 낮을수록 박막의 결정성은 향상되었다. Hall 측정 결과 RF파워가 20W일 때 전기비저항 $1.85{\times}10^{-3}{\Omega}cm$, 전하의 농도 $3.794{\times}10^{20}cm^{-3}$, 이동도 $8.89cm^2V^{-1}s^{-1}$로 전극으로서의 특성을 나타내었다. GZO 박막의 경우 RF 파워가 낮을수록 결정성이 높아지고, 전극의 특성을 갖는 것을 확인할 수 있었다.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.3
• /
• pp.57-61
• /
• 2016

We have studied the structural, optical and electrical properties of IGZO thin films. The IGZO thin films were deposited on the silicon wafer by RF magnetron sputtering method. The RF power in sputtering process was varied as 15W, 30W, 45W, 60W, 75W, respectively. All of the thin films transmittance in the visible range was above 85%. XRD analysis showed that amorphous structure of the thin films without any peak. The Hall measurements in the low RF power is the high mobility above $10cm^2/V{\cdot}s$ and the low resistvity are obtained in the IGZO thin films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.117-117
• /
• 1999

최근 광소자와 더불어 발전과 더불어 고효율의 새로운 광소자에 대한 수요가 증가되고 있다. ZnO는 이러한 특성을 가진 재료중에 한가지로서 최근 들어 그 가능성에 대한 연구가 활발히 이루어지고 있다. 특히 상온에서 exciton binding energy가 다른 재료보다 큰 60meV로 고효율의 blue, UV 발광이 가능한 재료로 알려져 있다. 본 연구에서도 광소자로서 ZnO를 활용하기 위해서 RF magnetron sputtering법을 이용하기 위하여 광특성의 향상에 목적을 두고 연구하였다. ZnO 박막은 RF magnetron sputtering법을 이용하여 sapphire (0001) 기판위에 성장시켰다. RF power는 60W에서 120W까지 변화시켰고 박막의 성장온도는 55$0^{\circ}C$와 $600^{\circ}C$로 변화시켰으며, 박막의 성장시간은 60분, ZnO target과 기판과의 거리는 4.5cm로 하여 성장시켰다. 성장된 ZnO 박막은 XRD $\theta$-rocking scan 측정을 통해서 박막의 C-축 배향성과 RBS channeling를 이용하여 ZnO 박막의 epitaxial 성장 정도를 측정하였다. 박막의 상온 발광 특성은 He-Cd laser를 사용한 photoluminescence spectra로 측정하였다. 또한 표면의 morphology는 atomic force microscope(AFM)를 이용하여 관찰하였으며 transmission electron microscopy(TEM)을 사용하여 ZnO박막의 단면적을 관찰함으로서 grain의 성장과 광특성 및 결정성과의 영향에 대해서 연구하였다. ZnO 박막의 성장온도 55$0^{\circ}C$에서 RF power를 60W에서 120W까지 변화시킬 경우 XRD $\theta$-rocking peak의 반치폭이 0.157$^{\circ}$에서 0.436$^{\circ}$까지 변화하였고 80W에서 최소값을 가졌으며 in-plain에 대한 XRD 측정 결과 ZnO 박막의 성장은 sapphire 기판에 대해서 30$^{\circ}$회전되어 성장된 것으로 알 수 있었으며 이는 ZnO [100]∥ Al2O3[110]의 관계를 갖는다는 것을 나타낸다. 광특성의 측정 결과인 PL peak의 반치폭은 133.67meV에서 89.5meV까지 변화함을 알 수 있었고 80W에서 최대값을 가졌으며 이는 RF power의 변화에 따른 결정성의 변화와는 반대되는 현상임을 알 수 있었다. 그러나 성장온도 $600^{\circ}C$일때에는 XRD $\theta$-rocking peak의 반치폭이 0.129$^{\circ}$로 결정성이 우수한 박막임을 확인할 수 있었고 PL peak의 반치폭 또한 Ar과 O2의 비율에 따라 76.32meV에서 98.77meV로 광특성도 우수한 것으로 나타났다. RBS channeling 결과 55$0^{\circ}C$에서는 $\chi$min값이 50~60%였으나 $600^{\circ}C$일 때에는 $\chi$min값이 4~5%로 박막이 epitaxial 성장을 하였다는 것을 알 수 있었다. 결정성과 광특성과의 연관성을 알아보기 위해 TEM을 이용한 박막의 cross section image를 관찰한 결과 광특성이 우수한 시편일수록 grain의 크기가 큰 것으로 나타났고 결정성이 우수한 시편의 경우에서는 XRD분석 결과에서처럼 C-축배향성이 우수한 것을 확인할 수 있었다. 이상의 결과로부터 RF magnetron sputtering 법으로 광특성이 우수한 양질의 ZnO박막 성장이 가능하였다는 것을 알 수 있었으며 광소자로써의 가능성을 확인 할 수 있었다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.9
• /
• pp.24-29
• /
• 2010

This paper presents the RF modeling for silicon nanowire MOSFET with 30 nm channel length and 5 nm channel radius. Equations for analytical parameter extraction are derived by analysis of Y-parameter. Accuracies of the new model and extracted parameters have been verified by 3-dimensional device simulation data up to 100 GHz. The model verifications are performed under conditions of saturation region ($V_{gs}$ = $_{ds}$ = 1 V) and linear region ($V_{gs}$ = 1 V, $V_{ds}$ = 0.5 V). The RMS modeling error of Y-parameters was calculated to be 1 %.

• Current Photovoltaic Research
• /
• v.8 no.1
• /
• pp.27-32
• /
• 2020

CuS thin films were deposited on glass substrates at room temperature by RF magnetron sputtering. The structural and optical properties of CuS thin films grown by varying RF-power from 40 W to 100 W were studied. From the XRD analysis, we confirmed hexagonal crystal structures grown in the preferred orientation of the (110) plane in all CuS thin films, and the intensity of the main diffraction peak increased in proportion to the increase of RF-power. In the case of CuS thin film deposited at 40W, small-sized particles formed a thin and dense surface morphology with narrow pore spacing, relatively. As the power increased, the grain size and grain boundary spacing increased sequentially. The peaks for the binding energy of Cu 2p_3/2 and Cu 2p_1/2 were determined at 932.1 eV and 952.0 eV, respectively. The difference in binding energy for the Cu²⁺ states was the same at 19.9 eV regardless of process parameters. The transmittance and band gap energy in the visible region tended to decrease with increasing sputtering powers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.48-48
• /
• 2007

P-type transparent conducting $CuGaO_2$ thin films have been prepared by DC/RF sputtering using Quartz(0001) and sapphire(0001) substrates. The target was fabricated by heating a stoichiometric mixture of CuO and $Ga_2O_3$ at 1373K for 12h under $N_2$ atmosphere. The film were deposited under mixture gas of Ar and $O_2(Ar:O_2=4:1)$ during 10~30min. and the as-deposited films were annealed at 1123K and $N_2$ atmosphere. Room temperature conductivity and the activation energy of the sintered body in the temperature range of 223K ~ 423K were 0 004S/cm, 1.9eV, respectively. XRD revealed that all of the as-deposited films were amorphous. Heating of the films deposited on Quartz substrates above 1123K resulted in crystallization with a second phase of $CuSiO_3$, which was assumed owing to reaction with Quartz substrate. The single phase of $CuGaO_2$ was obtained at the film deposited on the sapphire substrates. The transmittance after annealing of DC- and RF-sputtered films were 55~75% at 550nm. From the transmittance and reflectance measurement. the direct band gap of the DC/RF-sputtered films were 3.63eV and 3.57eV. and there was little difference between DC and RF sputtered films.

• Proceedings of the IEEK Conference
• /
• 2000.06e
• /
• pp.61-64
• /
• 2000

This paper describes a RF Down-Conversion Mixer for mobile communication systems. This circuit achieves low voltage operation and low power consumption by reducing stacked devices of conventional gilbert cell mixer. In order to reduce stacked devices, we use source-follower structure. The proposed RF Down-Conversion mixer operates up to 1.85GHz at 1.5V power supply with 0.25um CMOS technology and consumes 2.2mA.

• Proceedings of the IEEK Conference
• /
• 2002.06e
• /
• pp.55-58
• /
• 2002

This paper describes an RF module for 2.4GHz wireless audio/video transmission. The pre-processed baseband input signals are FM-modulated using a VCO and then transmitted through an antenna after RF filtering. The designed circuits are implemented using a Teflon board of which the size is 52mm${\times}$62mm. The measured maximum output signal levels are around -3dBm and the harmonics are less than -450dBc. The manufactured module consumes 130mA from a 8V supply.