• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.153-153
• /
• 2011

Ni $TiO_2$ nano composite coatings were fabricated by using pulse current electrodeposition technique at 100 Hz pulse frequency with a constant 50% pulse duty cycles and reference was taken with respect to the direct current electrodeposition. The properties of the composite coatings were investigated by using SEM, XRD, Wear test and Vicker's microhardness test. XRD patterns of pulse deposited composite coatings were found to be changed from preferred (100) orientation to the random mixed orientations. The results demonstrated that the Vickers microhardness of composite coatings under pulse condition was significantly improved than that of pure nickel coating as well as direct current electrodeposited Ni-$TiO_2$ composite coatings. Wear tracks have shown the less plastic deformation at pulse condition with reduced coefficient of friction. Nickel matrix grain size was also found to be lower in pulse plated composite coatings as compared to direct current electrodeposited composite coatings.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.3
• /
• pp.153-160
• /
• 2019

This study proposes a current source-type pulse generator to improve output voltage and current waveforms under a capacitively coupled plasma (CCP) system. The proposed circuit comprises two parallel-connected current source-type converters. These converters can satisfy the required output waveforms of plasma processing. The parallel-connected converters operate without reverse current fault by applying a time-delay control technique. Conventional voltage source converters based on pulse power supply exhibit drawbacks in short-circuit current, and problems occur when they are applied to a CCP system. The proposed pulse power supply based on a current source converter fundamentally solves the short-circuit current problem. Therefore, this topology can improve the voltage and current accuracy of a CCP system.

• Proceedings of the KIEE Conference
• /
• 1998.07e
• /
• pp.1773-1775
• /
• 1998

This paper deals with the pulse generator using PFN(Pulse Forming Network), and its operation characteristics and application. Two kinds of pulse generator were composed of the best appropriate condition circuit. The output current of the one pulse generator has the rise time of 28 ns and the pulse duration of $7{\mu}s$. The other pulse generator has high current of about 2kA. By use of the former generator with rapid rise time, the impulse impedance characteristic of ground electrodes was investigated with measuring the ground potential rise when the pulse current was injected into the ground electrode.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.90.1-90.1
• /
• 2012

1934년 J. R. Winkler에 의해 처음으로 개발된 pulse current 도금은 연속적인 직류 단속을 이용한 전기도금으로써 종래의 연속적인 직류(direct current) 전기 도금이 가지는 다공성 및 거친 도금 등의 한계를 극복하기 위해 연구되고 있다. 최근 전기 전자 산업의 급속한 발달과 함께 Au, Pd, Rh 등의 귀금속 도금에 있어서 Pulse 도금은 광택, 다공도, 내부 응력, 불순물 및 수소 함유량의 감소와 같은 특성 향상을 가질 수 있으며 기존 DC 전기 도금의 문제점 해결책으로서 많은 연구가 이루어지고 있다. 하지만 현재까지 Pulse 도금의 정확한 기구(mechanism)에 대한 명확한 정립이 되어 있지 않아 모든 도금계에 적용할 수 있는 standard pattern이 없는 실정이다. 본 연구에서는 귀금속 도금 중 Ag pulse 도금에 있어서 Peak current density, duty cycle, time이 Ag 도금의 표면 형상, 두께, 열전도율에 미치는 영향에 대해 연구하였다.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.685-688
• /
• 2000

Pulse plating is about to deposit material at high current density compared to conventional DC plating. For example pulse plating can get more fine grain can improve adhension and metal distribution and current efficiency can reduce internal stress and crack. therefore we studied pulsed power supply which has high current density and improve deposition quality and increase plating speed in this paper.

• Journal of the Korean institute of surface engineering
• /
• v.55 no.5
• /
• pp.292-298
• /
• 2022

In this study, PEO (plasma electrolytic oxidation) film formation behavior of AZ31 Mg alloy under application of 300 Hz pulse current was studied by the analyses of V-t curve, arc generation behavior, PEO film thickness and morphology of PEO films with treatment time in 0.05 M NaOH + 0.05 M Na₂SiO₃ + 0.1 M NaF solution. PEO films was observed to grow after 10 s of application of pulse current together with generation of micro-arcs. PEO film grew linearly with treatment time at a growth rate of about 5.58 ㎛/min at 200 mA/cm² of pulse current but increasing rate of film formation voltage became lowered largely with increasing treatment time after passing about 250 V, suggesting that resistivity of PEO films during micro-arc generation decreases with increasing film formation voltage at more than 250 V.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.5 no.2
• /
• pp.8-14
• /
• 1968

A linear current-pulse discriminator consisting: of a transistor monostable multivibrator and a Si tunnel diode is described. The input currant pulse range is about 50$\mu$A~5.23mA. The measured maximum linearity deviation is $\pm$0.75% in the input current pulse range mentioned above. The pulse resolving ability of the discriminator measured depends upon the bias current through the T, D. ; and, under the reverse bias current of 3mA, the resolving time is 2rs if allow the excess pulse amplitude of 5%. The threshold stability of the discriminator depends mainly upon the stability of the peak current Ip of the T. D. ; and, under the ambient temperature variation from $0^{\circ}C$ to 5$0^{\circ}C$, no bigger threshold variation than the maximum linearity deviation, i. e. $\pm$ 0.75%, was observed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.10a
• /
• pp.367-370
• /
• 2001

This paper proposes a new deterioration diagnostic technique for power facilities by analyzing the pulse-height analysis of leakage current. Until now, various deterioration diagnostic techniques to prevent power system failures by deterioration of power facilities are suggested, and most of which measures leakage current amplitude only as a estimation parameter. In this experiment, it is known that the pulse heights of the leakage current are increased according to deterioration progress as well as there comes remarkable changes in pulse height distribution thereto. Therefore, the use of pulse height distribution in deterioration diagnostic technique makes more accurate diagnosis than the conventional method by using only leakage current value. From the application test, it is confirmed that the proposed technique has sufficient performance to diagnose deterioration of power facilities.

• Journal of information and communication convergence engineering
• /
• v.8 no.5
• /
• pp.566-569
• /
• 2010

This paper describes the sinusoidal, pulse, triangular oscillator using second generation current conveyor. To obtain the sinusoidal waveform the circuit blocks are constructed by using all pass filter and integrator. The pulse and the triangular waveforms are obtained from the output of sinusoidal oscillator. The peak-to-peak voltages of sinusoidal and triangular waveforms can be easily controlled by the dc offset voltage. Also the output frequency of the oscillator can be controlled by varying passive elements. The designed circuit is verified by HSPICE simulation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.3
• /
• pp.280-289
• /
• 2015

A high-efficiency full-bridge DC-DC converter with a current-doubler rectifier and an asymmetric pulse-width modulation is proposed. Through the asymmetric pulse-width modulation, the proposed converter achieves zero-voltage switching of power switches without the circulating currents. The proposed converter reduces the output current ripple through the current-doubler rectifier. A control strategy is suggested for the proposed converter to charge battery banks. A constant current and constant voltage charging is performed. The proposed converter achieved a higher efficiency compared with the conventional full-bridge DC-DC converter with a phase-shift modulation. The performance of the proposed converter is evaluated by the experimental results for a 1.0 kW prototype circuit.