• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.389-390
• /
• 2006

The cycloidal reducer is one of the velocity controlling equipments in machinery. It has advantages of the higher reduction ratio, the higher accuracy, the easier adjustment of the transmission ratio and the smaller workspace than any other kinds of the reducers. This paper proposes a simple and exact approach for the lobe profile design of the two teeth difference cycloidal plate gear, which is different from the standard cycloidal reducer, by means of the principle of the instant velocity center in the general contact mechanism and the homogeneous coordinate transformation.

• 한국자동차공학회논문집
• /
• 제5권1호
• /
• pp.136-145
• /
• 1997

To analyzed ride quality and to predict durability in vehicle dynamics, it is essential to describe a road surface profile precisely. This paper presents a technique to generate road surface profiles in a spatial domain by using a power spectral density function. A single track power spectral density function is proposed to describe a road surface profile, which is also applicable for multi-track vehicle response analysis, The derived road surfaces are compared to ISO(International Organization for Standardization) standards and classifications, proposed by the MIRA(Motor Industry Research Association). The methodology in this paper is also proposed to generate road roughness description with a limited external data. A small amount of external curve data is combined with an internal PSD function to generate road surface roughness in a spatial domain.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.592-597
• /
• 2003

To solve a problem of micro drive due to small size and portability, it is necessary to understand and to investigate micro drive widely ,deeply. So, we performed modal analysis of suspension of micro drive, and load/unload experiment for Input current to VCM coil and disk speed. To determine the effect of ramp profile, curve fitting of lateral speed is performed with equation of speed. The results indicate that small load/unload speeds decrease the number of head/disk contacts, and during unloading process, low disk speed increase the number of head/disk contacts.

• Steel and Composite Structures
• /
• 제17권6호
• /
• pp.951-965
• /
• 2014

Point bending is commonly used for cambering and curving steel girders to large radii. In this system, a hydraulic ram or press is used to apply concentrated loads at selected points to obtain the required vertical (cambering) or horizontal (curving) curved profile from induced permanent deformations. This paper derives closed form solutions that relate loads to permanent deformations for horizontally curving wide flange steel beams based on their post-yield response. These solutions are presented in a parametric form to identify the relationship between key variables and their impact on the accuracy of the curving operation. It is shown that point bending could yield parabolic curved profiles that are within 1% of a desired circular curve if the span length to radius of curvature ratio (L / R) is less than 1.5 and the point loads are spaced at one third the beam length. Safe limits are then established on loads, strains and curvatures to avoid damaging the steel section. This leads to optimization of the point bending operation for inducing a circular profile in wide flange steel beams of any size.

• 한국유체기계학회 논문집
• /
• 제16권4호
• /
• pp.15-21
• /
• 2013

This study aims to estimate the fatigue resistance of small wind composite blade using the fatigue life estimation formula in the GL guideline. For this, firstly, we estimated a turbine blade's bending moment spectrum by using wind profile wind profile and BEMT. And fatigue tests were performed to obtain the S-N curve of composite materials used in blade. In addition, a finite element analysis was used to identify fatigue critical locations and fatigue stress spectrum. And the fatigue resistance of composite blade were evaluated using the rainflow cycle counting, and Goodman diagram and the fatigue life estimation formula in the GL guideline.

• 펄프종이기술
• /
• 제45권5호
• /
• pp.1-13
• /
• 2013

This study found fit optimum C, M, Y, K solid density and $CIEL^*a^*b^*$ value to paper & ink as well as check about printing machine state for color management in H-UV waterless off-set printing first. These values applied to GRACoL G7 calibration method. This method is one of color standard management method of printing. GRACoL G7 calibration method is possible stable tone reappearance by controlling gray balance by NPDC(Natural Printing Density Curve). Also, this study used values to make device profile as result that is gotten by application of GRACoL G7 calibration method. This profile was applied to CMS(Color Management System) of H-UV waterless off-set printing, and the result was possible by color management that correspond in printing quality standard of ISO 12647-2 and GRACol 2006 specifications.

• 한국태양에너지학회 논문집
• /
• 제32권2호
• /
• pp.74-86
• /
• 2012

For the improvement of environmental comfort in the buildings with the blind control, the objective of this study is to prevent the direct glare caused by the daylight inlet. During the process of solar profile prediction, time are significant factors that may cause error and glare during the blind control. This research proposes and evaluates the correction and control method to minimize prediction error. For the local areas with different longitude and local standard meridian, error occurred in the process of the time conversion from local standard time to apparent solar time. In order to correct error in time conversion, apparent solar time should be recalculated after adjusting the day of year and the equation of time. To solve the problems by the potential time errors, control method is suggested to divide the control sections using the calibrated fitting-curve and this method is verified through simulations. The proposed correction and control method, which considered potential time errors by loop lop leap years, could solve the problems about direct glare caused by daylight inlet on the work-plane according to the prediction errors of solar profile. And also these methods could maximize daylight inlet and solar heat gain, because the blocked area on windows could be minimized.

• 소음진동
• /
• 제8권5호
• /
• pp.841-848
• /
• 1998

In the gear manufacturing, tooth modification is usually applied for the prevention of tooth impact during the loading. In contrary, tooth profile error causes amplifying the whine noise which is cumbersome to reduce in the automobile gear box. So optimum quantity of the modifications must be obtained for the good performance in the vibrational sense. In this paper, a formulation to define the tooth curve by considering the profile manufacturing error and loading deformation of the gear tooth is suggested and the transmission error and loading deformation of the gear tooth is suggested and the transmission error with modified tooth in the gear system is evaluated. A pair of gear set is mathematically modelled. The equivalent excitation in the gear vibratonal model is formulated. For the experimental evaluaton on the derived transmission error function, a simple geared system is set up in which the gears are designed to give pre-designed tooth profile modification and manufactured by CNC Wire Cutting Machine. Under slow speed operaton, the transmission error of the gear pair is measured by using two rotational laser vibrometers, compared with the calculated one of which the result shows good agreement.

• 대한전자공학회논문지SD
• /
• 제48권10호
• /
• pp.62-66
• /
• 2011

본 연구에서는 측정된 S-파라미터를 사용하여 드레인-소스 전압 Vds에 무관한 게이트-소스 overlap 캐패시턴스를 추출하고, 이를 바탕으로 deep-submicron MOSFET의 Vds 종속 게이트-벌크 캐패시턴스 곡선을 추출하는 RF 방법이 새롭게 개발 되었다. 추출된 캐패시턴스 값들을 사용한 등가회로 모델과 측정된 데이터가 잘 일치하는 것을 관찰함으로써 추출방법의 정확도가 검증되었다. 추출된 데이터로부터 overlap과 depletion 길이의 Vds 종속 곡선이 얻어졌으며, 이를 통해 drain 영역의 채널 도핑 분포를 실험적으로 측정하였다.

• Restorative Dentistry and Endodontics
• /
• 제37권4호
• /
• pp.220-227
• /
• 2012

Objectives: The study was to compare the shaping ability of Reciproc (VDW) and WaveOne (Dentsply Maillefer) instruments compared with ProTaper, Profile and hand instrument during the preparation of simulated root canals. Materials and Methods: Five groups (n = 5) were established. Reciproc, WaveOne, ProTaper, Profile and K file (K-flexo file) were used to prepare the resin simulated canals. A series of preoperative and postoperative images were taken by a microscope and superimposed in 2 different layers. The amount of resin removed from both the inner and the outer sides of the canal was measured to the level of 10 mm from the apical tip, with a 1 mm increment. Results: The mean of resin removal from the inner canal wall was not different from the outer canal wall for Reciproc and WaveOne groups at apical third (1 - 3 mm level). There was no difference in the change of working length and maintenance of canal curvature. NiTi instruments are superior to stainless-steel K file in their shaping ability. Conclusions: Within the limitation of this present study, Reciproc and WaveOne instruments maintained the original canal curvature in curved canals better than ProTaper and Profile, which tend to transport towards the outer canal wall of the curve in the apical part of the canal.