• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.5
• /
• pp.492-498
• /
• 2015

As the integration of circuit components increases steadily, various EMS(Electromagnetic Susceptibility) problems have emerged from integrated circuits and electrical systems. The electromagnetic susceptibility of VCOs(Voltage Controlled Oscillator) is especially critical in RF systems. Therefore, in this paper, through the phase noise theory that models electrical oscillators as linear time variant systems, the EMS characteristics of representative VCO -ring VCO and LC VCO- with 1.2 GHz of reference oscillating frequency are analyzed under the existence of the electromagnetic noise coupled in power supply. An simulation algorithm is developed to extract impulse response function based on the phase noise theory. When there is no supply noise, the magnitude of the jitter of two oscillators were similar to around 2.1 ps, but in presence of supply noise, the jitter was significantly lower in LC VCOs than ring VCOs.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.10
• /
• pp.77-83
• /
• 2004

In low-power VLSI systems, it is effective to suppress leakage current by shutting down megablocks in idle states. Recently, multi-threshold voltage CMOS (MTCMOS) is widely accepted to shutdown power supply. However, it requires short wake-up time as operating frequency increases. This causes large current surge during wake-up process, and it often leads to system malfunction due to severe Power line noise. In this paper, a novel wake-up scheme is proposed to solve this problem. It exploits pipelined wake-up strategy in several stages that reduces maximum current on the power line and its corresponding power line noise. To evaluate its efficiency, the proposed scheme was applied to a multiplier block in the Compact Flash memory controller chip. Power line noise in shutdown and wake-up process was simulated and analyzed. From the simulation results, the proposed scheme was proven to greatly reduce the power line noise compared with conventional schemes.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.181-184
• /
• 2005

Operating conditions of photovoltaic power generator is very sensitive to the PV modules. The PV module's control is an importance issue in the removing DC ripple noise. In this paper, the phase-shifted-carrier technique, which is a new three-step dc-dc power multi-converter schemes, is applied to solar generator system to improve the output current waveform. The novel type of three-step dc-dc converter presented has many features such as the good output waveform, high efficiency, low switching losses, low acoustic noise. The circuit configuration is constructed by the conventional full-bridge type converter circuit using the isolated DC power supply for which the solar cell is very suitable. In the end, a circuit design for understanding three-step dc-dc converter and new solar power system were presented

• Journal of Korea Multimedia Society
• /
• v.6 no.1
• /
• pp.161-166
• /
• 2003

This paper presents a high gain LNA for a bluetooth application using 0.25$\mu\textrm{m}$ CMOS technology. The conventional one stage LNA has a low power gain. The presented one stage LNA using a cascode inverter LNA with a voltage reference and without a choke inductor has an improved Power gain. Simulation results of the 2.4GHz designed LNA shows a high power gain of 21dB, a noise figure of 2.2dB, and the power consumption of 255mW at 2.5V power supply.

• Journal of Sensor Science and Technology
• /
• v.26 no.1
• /
• pp.60-65
• /
• 2017

This paper describes the low noise and low power IC using the opamp sharing technique for the capacitive micro-sensor sensing platform. The proposed IC reduces noise using correlated double sampling (CDS) and reduces power consumption using the opamp sharing technique. The IC is designed to be fully programmable, and can be digitally controlled by serial peripheral interface (SPI). The power consumption and the integrated input referred noise are 1.02 mW from a 3.3 V supply voltage and $0.164aF_{RMS}$ with a bandwidth of 400 Hz. The capacitive sensitivity, the input-output linearity and the figure of merits (FoM) are 2.5 mV/fF, 2.46 %FSO, and 8.4, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.4
• /
• pp.492-498
• /
• 2017

In this paper, we integrate a divide-by-3 injection-locked frequency divider (ILFD) in CMOS technology with a $0.18-{\mu}m$ BiCMOS process. We propose a self-injection technique that utilizes harmonic conversion to improve the locking range, phase-noise, and input sensitivity simultaneously. The proposed self-injection technique consists of an odd-to-even harmonic converter and a feedback amplifier. This technique offers the advantage of increasing the injection efficiency at even harmonics and thus realizes the low-power implementation of an odd-order division ILFD. The measurement results using the proposed self-injection technique show that the locking range is increased by 47.8% and the phase noise is reduced by 14.7 dBc/Hz at 1-MHz offset frequency with the injection power of -12 dBm. The designed divide-by-3 ILFD occupies $0.048mm^2$ with a power consumption of 18.2-mW from a 1.8-V power supply.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.2
• /
• pp.72-75
• /
• 2011

In this paper, the voltage across the LED system supplied by positive voltage of power supply system the power consumption of the LED itself, and uses a lot of transformers and analog devices, such as converter startup problems and constant temperature even when the voltage driving abnormally LED current in the destruction caused by the flow of a lot of problems can occur. In this paper, we obtain the technology of consistent current using PWM(pulse width modulation) mode in order to minimize analog devices and eventually discuss the technology to develop consistent output converter using power drive IC.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.270-272
• /
• 2004

At the water supply field, high voltage induction motor is main facility of a load equipment. The motor is often out of order and its noise, generated heat, loss etc occurred occasionally. especially, transmission motor for flux control generates an amount of the harmonics then have a bad influence upon the electric power system. In this study, to analyze the total harmonics distortion of the water supply field receiving high voltage, the harmonics measured and analyzed using the PQA(Power quality Analyzer) according to the electric power system and electrical load and the reduction method presented.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.2
• /
• pp.53-57
• /
• 2017

This paper proposes a 401MHz-406MHz low noise amplifier for MedRadio applications. The proposed low noise amplifier adopts a common gate amplifier topology using current reuse gm-boosting technique. The proposed low noise amplifier shows better performance of voltage gain and noise figure than the conventional gm-boosted common gate amplifier in the same power consumption. The proposed current-reuse gm-boosted low noise amplifier achieves a voltage gain of 22 dB, a noise figure of 2.95 dB, and IIP3 of -17 dBm while consuming $170{\mu}W$ from a 0.5 V supply voltage in $0.13{\mu}m$ CMOS process.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.2
• /
• pp.37-44
• /
• 2008

This paper presents a 5.8 GHz PLL using high-speed ring oscillator for WLAN. The proposed ring oscillator has been designed using the negative skewed delay scheme and for differential mode operation. Therefore, the oscillator is insensitive to power-supply-injected noise, and it has the merit of low 1/f noise because tail current sources are not used. The output frequency ranges from 5.13 to 7.04 GHz with the control voltage varing from 0 to 1.8 V. The proposed PLL circuits have been designed, simulated, and proved using 0.18 um 1.8 V TSMC CMOS library. At the operation frequency of 5.8 GHz, the locking time is 2.5 us and the simulated power consumption is 59.9 mW.