• 한국수소및신에너지학회논문집
• /
• 제27권5호
• /
• pp.503-509
• /
• 2016

Fuel cell is a device for producing electricity by using the hydrogen produced by the fuel processor. At this time, CO is also created by the fuel processor. The resulting CO enters the stack where is produce electricity and leads to the adsorption of anode catalyst, finally the CO poisoning occurs. Stack which occurred CO poisoning has a reduction in performance and shelf life are gradually fall because they do not respond to hydrogen. In this paper, experiments that using a PROX reactor to prevent CO poisoning were carried out for removing the CO concentration to less than 10ppm range available in the fuel cell. Furthermore experiments by the PROX reaction was designed and manufactured with a water-cooling heat exchange reactor to maintain a suitable temperature control due to the strong exothermic reaction.

• 한국수소및신에너지학회논문집
• /
• 제30권6호
• /
• pp.601-607
• /
• 2019

Ammonia would be formed in natural gas containing small amount of nitrogen reforming process in the process natural gas, which might damage the Pt catalyst and Prox catalyst. In the article, the effect of nitrogen contents on the formation of ammonia in the reforming process has been studied. In the experiments, Ru based and Ni based catalysts were used and the concentration of ammonia in the reformate gas at various gas hourly space velocity was measured. Experimental result shows that relatively higher ammonia concentration was measured with Ru based catalyst than with Ni based catalyst. It also shows that the concentration of ammonia increased rapidly after most of the methane converted into hydrogen. Based on the experimental results to reduce ammonia concentration it might be better to finish methane conversion at the exit position of the reforming reactor to minimize the contact time of catalyst and nitrogen with high concentration of hydrogen.

• 한국표면공학회지
• /
• 제45권2호
• /
• pp.75-80
• /
• 2012

A sputter-sublimation source was tested for high rate deposition of protective coating of PEMFC(polymer electrolyte membrane fuel cell) with high electrical conductivity and anti-corrosion capability by DC biasing of a metal rod immersed in inductively coupled plasma. A SUS(stainless steel) tube, rod were tested for low thermal conductivity materials and copper for high thermal conductivity ones. At 10 mTorr of Ar ICP(inductively coupled plasma) with 2.4 MHz, 300 W, the surface temperature of a SUS rod reached to $1,289^{\circ}C$ with a dc bias of 150 W (-706 V, 0.21 A) in 2 mins. For 10 min of sputter-sublimation, 0.1 gr of SUS rod was sputter-sublimated which is a good evidence of a high rate deposition source. ICP is used for sputter-sublimation of a target material, for substrate pre-treatment, film quality improvement by high energy particle bombardment and reactive deposition.

• 대한금속재료학회지
• /
• 제46권12호
• /
• pp.817-822
• /
• 2008

Metal matrix composite (MMC) materials having low electrical contact resistance based on 316L stainless steel (STS) matrix alloy with $ZrB_2$ particles were fabricated for PEMFC (Polymer Electrolyte Membrane Fuel Cell) separator by powder metallurgy (PM). The effects of the boride particle addition into the matrix alloy on microstructure, surface morphology, and interfacial contact resistance (ICR) between the samples and gas diffusion layer (GDL) were investigated. Both conventional and PM 316L STS samples showed high ICR due to the existence of non-conductive passive film on the alloy surface. The addition of the boride particles, however, remarkably reduced ICR of the samples. SEM observation revealed that the boride particles were protruded out of the matrix surface and particle density existing on the surface increased with increasing the boride content, causing increase of the total contact area between the conductive particles and GDL. ICR of the samples also decreased with increasing the boride content resulted from the increased contact area.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.153-156
• /
• 2012

본 논문에서는 연료전지의 성능향상 및 신뢰성 확보를 위한 연료전지 최적화 및 탑재화 연구를 수행하였다. 고분자 전해질막 연료전지의 성능 향상을 위한 실험은 연료전지에 부하를 걸어 발생되는 전류와 전압을 측정하여, 상용 연료전지 데이터와 비교 분석하였다. 이를 바탕으로 무인항공기 연료전지 탑재상태에서의 최적화를 위한 제어기를 제작하고, 제어 알고리즘 구성을 통해 연료전지를 탑재한 무인항공기의 최적의 성능유지를 위한 연구를 수행하였다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.578-583
• /
• 2006

This paper introduces conceptual design of scroll expander-compressor unit for fuel cell. Since air discharged out of the fuel cell stack after reaction has still high pressure energy, some power can be extracted out of it by directing it to pass through an expanding device so that the extracted power can be used to drive an auxiliary compressor. For this purpose, a scroll type expander coupled to a scroll type compressor was designed: orbiting scroll of the expander and that of the compressor were made to share three of common drive pins installed in the mid frame plate, and central cavity in the mid-plate was used as a back pressure chamber to provide axial compliance for both orbiting scrolls. Performance analysis for the expander showed that the shaft power of the expander could reduce the auxiliary power consumption in the fuel cell by about one third at the scroll clearance of $10{\mu}m$.

• Corrosion Science and Technology
• /
• 제20권6호
• /
• pp.435-450
• /
• 2021

The interest in eco-friendly energy is increasing, and polymer electrolyte membrane fuel cell (PEMFC) is attracting attention as alternative power sources. Research on metallic bipolar plates, a fuel cell component, is being actively conducted. However, since the operating conditions of PEMFC, in which sulfuric acid (H₂SO₄) and hydrofluoric acid (HF) are mixed, are strong acidity, the durability of the metallic bipolar plate is very important. In this research, the electrochemical characteristics and corrosion damage behavior of 316L stainless steel, a material for metallic bipolar plates, were analyzed through potentiostatic corrosion tests with test times and chloride concentrations. As the test times and chloride concentrations increased, the current density and corrosion damage increased. As a result of observation with scanning electron microscope(SEM) and 3D microscope, both the depth and width of pitting corrosion increased with increases in test times and chloride concentrations. In particular, the pitting corrosion damage depth at test conditions of 6 hours and 1000 ppm chloride increased the most. The growth of the pitting corrosion damage was not directly proportional to time and increased significantly after a certain period.

• Corrosion Science and Technology
• /
• 제20권6호
• /
• pp.347-360
• /
• 2021

Currently, the demand for eco-friendly energy sources is high, which has prompted research on polymer electrolyte membrane fuel cells. Both aluminum alloys and nickel alloys, which are commonly considered as materials of bipolar plates in fuel cells, oxide layers formed on the metal surface have excellent corrosion resistance. In this research, the electrochemical characteristics of 6061-T6 aluminum alloy and Inconel 600 were investigated with chloride concentrations in an acid environment that simulated the cathode condition of the PEMFC. After potentiodynamic polarization experiments, Tafel analysis and surface analysis were performed. Inconel 600 presented remarkably good corrosion resistance under all test conditions. The corrosion current density of 6061-T6 aluminum alloy was significantly higher than that of Inconel 600 under all test conditions. Also, 6061-T6 aluminum alloy and Inconel 600 presented uniform corrosion and intergranular corrosion, respectively. The Ni, Cr, and Fe, which are the main chemical compositions of Inconel 600, are higher than Al in the electromotive force series. And a double oxide film of NiO-Cr₂O₃, which is more stable than Al₂O₃, is formed. Thus, the corrosion resistance of Inconel 600 is better.

• 공업화학전망
• /
• 제24권3호
• /
• pp.14-27
• /
• 2021

수소 에너지는 환경 문제를 최소화하고 고갈되는 화석연료를 대체할 수 있는 에너지원으로 각광을 받고 있다. 수소연료전지는 이러한 수소를 에너지원으로 사용하고 수소를 전기에너지로 전환하여 그 부산물로 물을 만드는 대표적인 친환경 전기화학 장치이다. 고분자 전해질막 연료전지는 수소이온교환 특성을 갖는 고분자막을 전해질로 사용하는 연료전지로 막전극집합체의 전극층은 촉매가 포함된 고분자 전해질막 연료전지의 주요 요소 중의 하나이다. 소재개발 측면에서 고분자 전해질막 연료전지 전극층 핵심 소재의 물성 발현 원리 등을 이해하고 최적화된 소재 설계를 위해서는 원자레벨에서의 소재 설계 접근법이 필요하다. 따라서 실험적인 연구가 어려운 부분과 원자단위에서의 물질 현상에 대한 이해 그리고 연구 개발의 효율성 증진을 위해 전산재료과학(computational materials science) 기술이 광범위하게 활용될 수 있다. 본 기고문에서는 고분자 전해질막 연료전지에서의 전극층 소재에 대한 분자동역학 기반의 전산모사 활용과 연구동향에 대하여 소개하고자 한다.

• 한국수소및신에너지학회논문집
• /
• 제34권1호
• /
• pp.1-7
• /
• 2023

A fuel handling process combined with a pressure swing adsorption system (PSA) was simulated to produce pure hydrogen with a purity greater than 99.97%. The simulation consists of two parts. The fuel processing part consisting of reformer and water-gas shift reaction was simulated with Aspen plus^®, and the hydrogen purification part consisting of PSA was simulated with Aspen Adsorption^®. In this study, the effect of reformer temperature and pressure on the total hydrogen production yield was investigated. Simulations were performed over a temperature range of 700 to 1,000℃ and a pressure range of 1 to 10 bar. The total hydrogen production yield increased with increasing temperature and decreasing pressure. The maximum hydrogen yield was less than 50% in the simulation and will be lower in the real process.