• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.491-492
• /
• 2006

We report on the fabrication of organic-based flexible display using an amorphous IZO anode grown at room temperature. The IZO anode films were grown by a conventional DC reactive sputtering on polycarbonate (PC) substrate at room temperature using a synthesized IZO target in a Ar/$O_2$ ambient. X-ray diffraction examination results show that the IZO anode film grown at room temperature is complete amorphous structure due to low substrate temperature. It is shown that the $Ir(ppy)_3$ doped flexible organic light emitting diode (OLED) fabricated on the IZO anode exhibit comparable current-voltage-luminance characteristics to OLED fabricated on conventional ITO/glass substrate. These findings indicate that the IZO anode film grown on PC substrate is a promising anode materials for the fabrication of organic based flexible displays.

• Polymer(Korea)
• /
• v.37 no.6
• /
• pp.753-763
• /
• 2013

Laser transmission welding of polymers is now used in a very wide range of industries due to its advantages. If the joining between polypropylene (PP) and polycarbonate (PC) occurs by laser transmission welding, the automotive headlight will get a large profit. However, PP/PC have poor miscibility. In the laser transmission welding results, the adhesion strength between PP and PC was very weak. In this study, PP was modified by grafting of glycidyl methacrylate (GMA). The adhesion strength of PC and PP-g-GMA as a reactive compatibilizer was observed. The adhesion strength was investigated by compatibility with PC, mechanical properties and laser transmission welding.

• Journal of Surface Science and Engineering
• /
• v.47 no.6
• /
• pp.341-346
• /
• 2014

Ga-doped ZnO (GZO) single layer and $SiO_2/GZO$ bi-layered films were deposited on Polycarbonate(PC) substrate by radio frequency magnetron sputtering. Influence of the structural, electrical, and optical properties of the films was considered. We have considered the influence of electron irradiation energy of 450 and 900 eV on the stuctural, electrical and optical properties of $SiO_2/GZO$ thin films. The optical transmittance in a visible wave length region increased with the electron irradiation energy. The electrical resistivity of the films were dependent on the electron's irradiation energy. The $SiO_2/GZO$ films irradiated at 900 eV were showen the lowest resistivity of $7.8{\times}10^{-3}{\Omega}cm$. The film which was irradiated by electron at 900 eV shows 84.3% optical transmittance and also shows lower than contact angle of $58^{\circ}$ in this study.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.85-91
• /
• 2009

There has been a rapid progress for flexible polymer-based MEMS(Microelectromechanical Systems) technology. Polycarbonate (PC) and Poly Methyl Methacrylate (PMMA), so-called acrylic, have many advantages for optical, non-toxic and micro-device application. We studied dry etching of PC and PMMA as a function of % gas ratio in the $O_2/SF_6/CH_4$ temary plasma. A photoresist pattern was defined on the polymer samples with a mask using a conventional lithography. Plasma etching was done at 100 W RIE chuck power and 10 sccm total gas flow rate. The etch rates of PMMA were typically 2 times higher than those of PC in the whole experimental range. The result would be related to higher melting point of PC compared to that of PMMA. The highest etch rates of PMMA and PC were found in the $O_2/SF_6$ discharges among $O_2/SF_6$, $O_2/CH_4$ and $SF_6/CH_4$ and $O_2/SF_6/CH_4$ plasma composition (PC: ${\sim}350\;nm/min$ at 5 sccm $O_2/5$ sccm $SF_6$, PMMA: ${\sim}570\;nm/min$ at 2.5 sccm $O_2/7.5$ sccm $SF_6$). PC has smoother surface morphology than PMMA after etching in the $O_2/SF_6/CH_4$ discharges. The surface roughness of PC was in the range of 1.9$\sim$3.88 nm. However, that of PMMA was 17.3$\sim$26.1 nm.

• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.929-932
• /
• 2012

Novel platform technology has been developed to replace the photolithography used currently for manufacturing semiconductors and display devices. As a substrate, plastics, especially polycarbonates, have been considered for future application such as flexible display. Other plastics, i.e. polyimide, polyetheretherketon, and polyethersulfone developed for the substrate at this moment, are available for photolithography due to their high glass transition temperature, instead of high price. After thin polystyrene film was coated on the polycarbonate substrate, microstructure of the film was formed with polydimethylsiloxane template over the glass transition temperature of the polystyrene. The surface of the structure was treated with potassium permanganate and octadecyltrimethoxysilane so that the surface became hydrophobic. After this surface treatment, the nanoparticles dispersed in aqueous solution were aligned in the structure followed by evaporation of the DI water. Without the treatment, the nanoparticles were placed on the undesired region of the structure. Therefore, the interfacial interaction was also utilized for the nanoparticle alignment. The surface was analyzed using X-ray photoelectron spectrometer. The evaporation of the solvent occurred after several drops of the solution where the hydrophilic nanoparticles were dispersed. During the evaporation, the alignment was precisely guided by the physical structure and the interfacial interaction. The alignment was applied to the electric device.

• Journal of the Korean Vacuum Society
• /
• v.18 no.6
• /
• pp.440-446
• /
• 2009

Indium tin oxide(ITO) substrate is one of the key components of the touch panel and its sputtering process is dependent on the characteristics of various touch panel, such as driving type, size of panel, and the intended use. In this study, we optimized the sputtering condition of ITO film on polycarbonate(PC) by using in-line sputtering method for the application to resistive type touch panel. We varied the $O_2$/Ar gas ratio, sputtering power, pressure and moving speed of substrate to deposit ITO films at room temperature with the base vacuum of $1{\times}10^{-6}\;torr$. The sheet resistance and its uniformity, the transmittance, the thickness of the ITO film on PC substrate are investigated and analyzed. The optimized process parameters are as follows : the sheet resistance is $500{\pm}50\;{\Omega}$/□, the uniformity of sheet resistance is lower than 10%, the transmittance is higher than 87 % at 550nm, and the thickness is about 120~250. The optimized deposition conditions by in-line sputtering method can be applied to the actual mass production for the ITO film manufacturing technology.

• Polymer(Korea)
• /
• v.38 no.4
• /
• pp.471-476
• /
• 2014

Polycarbonate (PC) and acrylonitrile-butadiene-styrene (ABS) blends were prepared using a high shear extruder to investigate their thermal decomposition and mechanical properties with shear rate and shear time. In this experiment, high shear rate, from 1000 to 3000 rpm, in blending process was applied for 10 to 40 sec, respectively. At high shear rate over than 2000 rpm, the initial decomposition temperature was dropped significantly compared to a compounded sample because of thermal decomposition of the blend by high shear. Consequently, high shear processing gave an important effect on the mechanical and thermal properties of the PC/ABS blend. In particular, elongation of the blend decreased significantly with shear rate.

• Polymer(Korea)
• /
• v.37 no.3
• /
• pp.373-378
• /
• 2013

The interfacial adhesion strength is very important in $SiO_x$ deposited PC film for the barrier enhanced polycarbonate (PC) flexible substrate. In this study, PC films were treated by undercoating, UV/$O_3$ and low temperature plasma and then the effect of physical and chemical surface modifications on the interfacial adhesion strength between PC film and $SiO_x$ barrier layer were studied. It was found that untreated PC film shows significantly low interfacial adhesion strength due to the smooth surface and low surface free energy of PC. Low temperature plasma treatments resulted in the increase of both surface roughness and surface free energy due to etching and the appearance of polar molecules on the PC surface. However, UV/$O_3$ treatment only shows the increase of surface free energy by developed polar molecules on the surface. These surface modifications caused the enhancement of surface interfacial strength between PC film and $SiO_x$ barrier. In the case of undercoating, it was found that the increase of surface interfacial strength was achieved by adhesion between various acrylic acid on acrylate coated surface and $SiO_x$ without increase of polar surface energy. In addition, the barrier property is also improved by organic-inorganic hybrid multilayer structure.

• Fire Science and Engineering
• /
• v.33 no.3
• /
• pp.21-28
• /
• 2019

To examine the mechanical and combustion characteristics of FRTP, either polycarbonate or nylon were used as a matrix, and either glass fiber or carbon fiber were used as the fiber reinforcement. The fiber reinforcement content was differentiated at 0~40 wt%. The tensile strength and heat distortion temperature increased with increasing reinforcement content. When the fiber reinforcement content was above 30 wt%, the flammability rating showed V-0. As the fiber reinforcement content increased from 0 to 40 wt%, the peak heat release rate of polycarbonate decreased by approximately 51% and that of nylon decreased by approximately 24%. The rate of CO generation decreased for a period of time, and then increased. This appears to have resulted from incomplete combustion. The rate of CO₂ generation shows a similar tendency with the heat release rate. As fiber reinforcement content levels increased from 0 to 40 wt%, the CO₂ peak rate of polycarbonate generation decreased by approximately 50% and that of nylon decreased by 28%.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.26 no.4
• /
• pp.433-445
• /
• 2010

The aim of this study was to evaluate the fixation effect by connecting impression copings and to compare the three types of impression trays which were used in open tray impression technique. Experimental groups used 3 types of impression trays which are custom tray, plastic metal combination tray and polycarbonate stock tray. These three groups were subdivided into splinted and non-splinted impression copings group. The total number of experimental groups was six. 10 specimens were made for each group. We used 1-screw test, observing the specimen on which only one side abutment of reference framework was fixated with 20 Ncm. The gap between implant analogue and abutment of the other side was observed by stereo microscope. It was measured at 6 points in each specimen. Measuring value was selected when same result was revealed 3 times. Recorded data were statistically analyzed. Whether impression copings were splinted or not, there was no significant difference among custom tray group, plastic metal combination tray group, and polycarbonate stock tray group. Significant statistical difference in vertical fit discrepancy was found between splinted and non-splinted impression copings group with custom tray, plastic metal combination tray and polycarbonate stock tray (p<0.05).