• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.9
• /
• pp.98-105
• /
• 1995

Recent microwave IC's reach to the extent of high operating frequencies at which bonding wires limit their performance as dominant parasitic components. Double bonding wires separated by an internal angle have been firstly characterized using the Method of Moments with the incorporation of the ohmic resistance calculated by the phenomenological loss equivalence method. For a 30$^{\circ}$ internal angle, the calculated total reactance is 45% less than that of a single bonding wire due to the negative mutual coupling effect. The radiation effect has been observed decreasing the mutual inductance, whereas for parallel bonding wires it greatly increases the mutual inductance. This calculation results can be widely used for designing and packaging of high frequency and high density MMIC's and OEIC's.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.939-940
• /
• 2006

An integrated inductor using the low-temperature co-fired ceramics(LTCC ) technology for low-power electronics was fabricated. In the inductor NiZn ferrite sheet(${\mu}_r=230$), was embedded to increase inductance. The inductor has Ag spiral coil with 14 turns($7turns{\times}2layers$), a dimension of 0.6mm in width, 10um in thickness, and 0.15mm pitch. To evaluate the inductance, including the parasitic resistance, the fabricated inductor was calculated and measured. It was confirmed that calculated values were very close to the measured values. Finally as an application of the LTCC integrated inductor to low power electronic circuits, a LTCC buck DC/DC converter with 1W output power and up to 0.5MHz switching frequency using the inductor fabricated was develop.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.10
• /
• pp.534-539
• /
• 2006

An integrated inductor using the low-temperature co-fired ceramics(LTCC) technology for low-power electronics was fabricated. In the inductor NiZn ferrite sheet$({\mu}_r=230)$, was embedded to increase inductance. The inductor has Ag spiral coil with 14 turns$(7turns{\times}2layers)$, a dimension of 0.6mm in width, 10um in thickness, and 0.15mm pitch. To evaluate the inductance, including the parasitic resistance, the fabricated inductor was calculated and measured. It was confirmed that calculated values were very close to the measured values. Finally as an application of the LTCC integrated inductor to low power electronic circuits, a LTCC boost DC/DC converter with 1W output power and up to 0.5MHz switching frequency using the inductor fabricated was developed.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.188-189
• /
• 2010

This paper proposed a new zero-voltage switching(ZVS) Two-Inductor boost converter. The conventional Two-Inductor boost converter has defect. When the switch is turned off, the high voltage spike is occurred in the switch by leakage inductance and switch parasitic capacitor. To solve this problem, the parallel resonant capacitor is added to the conventional Two-Inductor boost converter. Using quasi-resonant between parallel resonant capacitance and leakage inductance, the switches is operated soft switching. A reduction of transformer turn ratio is achieved by the voltage doubler rectifier.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.4
• /
• pp.274-280
• /
• 2007

This paper demonstrates an efficiency improvement of the class E power amplifier (PA) by tuning-out the input capacitance ($C_{IN}$) of the power HBT with a shunt inductance. In order to obtain high output power, the PA needs the large emitter size of a transistor. The larger the emitter size, the higher the parasitic capacitance. The parasitic $C_{IN}$ affects the distortion of the voltage signal at the base node and changes the duty cycle to decrease the PA's efficiency. Adopting the L-C resonance, we obtain a remarkable efficiency improvement of as much as 7%. This PA exhibits output power of 29 dBm and collector efficiency of 71% at 1.9 GHz.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2151-2155
• /
• 1998

The traveling wave type ultrasonic motor(USM) has no electro-magnetic circuits( coil or core). The driving principle of the USM is based on high-frequency mechanical vibrations and frictional force. The USM, thus, is fed by two-phase high - frequency sinusoidal inverter using its series resonant parasitic components. For the using of series resonant type inverter, it should be needed to a USM parasitic capacitance and a proper inductor chosen. In this paper, the values of optimal inductance are designed and the efficiency of USM drives is achieved. The effectiveness of the proposed design is demonstrated by experiments.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.828-832
• /
• 1995

This paper describes the efficient design, analysis method and experimental verification of capacitor discharge impulse magnetizer system. A capacitor discharge magnetizer system is used to produce a high current impulse of short duration in this magnetizing fixture. The parasitic resistance and parasitic inductance of the capacitor discharge impulse magnetizer system have been estimated using known air-core test coil. Finite element analysis (using MAXWELL 2-D field simulator) and magnetizing circuit analysis (using SPICE) are also used as part of the design and analysis process of the capacitor discharge impulse magnetizer system. Application study for a magnetizing fixture design is shown. 8-pole magnetizing fixture has been designed and analyzed using finite element analysis. The fixture design for 8-pole magnet are presented along with the experimental results. The experimental results have been achieved using a high-voltage, high-energy capacitor discharge impulse magnetizer and 8-pole iron core fixtures (charging voltage : 2000[V], capacitor bank : 4000[$\mu\textrm{F}$]).

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.1
• /
• pp.88-96
• /
• 2016

In this paper, the GaN FET based phase-shift full-bridge dc-dc converter design is implemented. Switch characteristics of GaN FET were analyzed in detail by comparing state-of-the-art Si MOSFET. Owing to the low conduction resistance and parasitic capacitance, it is expected to GaN FET based power conversion system has improved performance. However, GaN FET is vulnerable to electric interference due to the relatively low threshold voltage and fast switching transient. Therefore, it is necessary to consider PCB layout to design GaN FET based power system because PCB layout is the main reason of stray inductance. To reduce the electric noise, gate voltage of GaN FET is analyzed according to operation mode of phase-shift full-bridge dc-dc converter. Two 600W phase-shifted full-bridge dc-dc converter are designed based on the result to evaluate effects of stray inductance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.2
• /
• pp.140-149
• /
• 2017

This study proposes a new type of active-clamp forward-flyback converter with two transformers that operate in forward and flyback modes during on and off times, respectively, instead of not using an output inductor. The main switch can be turned on with zero-voltage switching (ZVS) using the leakage inductance of the transformer and the output capacitor of the main switch. The leakage inductance should be increased to ZVS. However, the ringing between the leakage inductance of the transformer and the parasitic output capacitance of the secondary side rectifier switches results in a serious voltage spike. A forward-flyback converter employing auxiliary inductor and auxiliary diode is proposed to overcome the problem. The operational principles are analyzed in detail and validated through experiments with a 385 V-to-53 V/37 A prototype.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1469-1479
• /
• 2017

Primary-side regulation (PSR) scheme is widely applied in low power applications, such as cell phone chargers, network adapters, and LED drivers. However, the efficiency and standby power requirements have been improved to a high standard due to the new trends of DOE (Department Of Energy) Level VI and COC (Code Of Conduct specifications) V5. The major drawbacks of PSR include poor regulation due to inaccurate feedback and difficulty in acquiring acceptable regulation. A novel adaptive blanking strategy for constant current and constant voltage regulation is proposed in this paper. An accurate model for the sample blanking time related to transformer leakage inductance and the metal-oxide-semiconductor field-effect transistor (MOSFET) parasitic capacitance is established. The proposed strategy can achieve accurate detection for ultra-low standby power. In addition, numerous control factors are analyzed in detail to eliminate the influence of leakage inductance on the loop stability. A dedicated controller integrated circuit (IC) with a power MOSFET is fabricated to verify the effectiveness of the proposed control strategy. Experimental results demonstrated that the prototype based on the proposed IC has excellent performance.