• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.3
• /
• pp.28-34
• /
• 2010

In this paper, the transceiver for RFID reader using 13.56MHz as a carrier frequency and meeting International Standard ISO 14443 type A, 14443 type B and 15693 is presented. The receiver is composed of envelope detector, VGA(Variable Gain Amplifier), filter, comparator to recovery the received signal. The proposed automatic reference voltage generator, positive peak detector, negative peak detector, and data slicer circuit can adjust the decision level of reference voltage over the received signal amplitudes. The transmitter is designed to drive high voltage and current to meet the 15693 specification. By using inductor loading circuit which can swing more than power supply and drive large current even under low impedance condition, it can control modulation rate from 30 percent to 5 percent, 100 perccnt and drive the output currents from 5 mA to 240 mA depending on standards. The 13.56 MHZ RFID reader is implemented in $0.18\;{\mu}m$ CM08 technology at 3.3V single supply. The chip area excluding pads is $1.5mm\;{\times}\;1.5mm$.

• Journal of IKEEE
• /
• v.14 no.1
• /
• pp.65-74
• /
• 2010

The Digital TV(DTV) standard has ushered in a new era in TV broadcasting and raised a great demand for DTV tuners. There are many challenges in designing a DTV tuner, of which the most difficult part is the frequency synthesizer. This paper presents the design of a frequency synthesizer for DTV Tuners in a $0.18{\mu}m$ CMOS process. It satisfies the DTV(ATSC) frequency band(54~806MHz). A scheme is proposed to cover the full band using only one VCO. The VCO has been designed to operate at 1.6~3.6GHz band such that the LO pulling effect is minimized, and reliable broadband characteristics have been achieved by reducing the variations of VCO gain and frequency step. The simulation results show that the designed VCO has gains of 59~94MHz(${\pm}$17.7MHz/V,${\pm}$23%) and frequency steps of 26~42.5MHz(${\pm}$8.25MHz/V,${\pm}$24%), and a very wide tuning range of 76.9%. The designed frequency synthesizer has a phase noise of -106dBc/Hz at 100kHz offset, and the lock time is less than $10{\mu}$sec. It consumes 20~23mA from a 1.8V supply, and the chip size including PADs is 2.0mm${\times}$1.8mm.

• The Korean Journal of Emergency Medical Services
• /
• v.16 no.1
• /
• pp.81-90
• /
• 2012

Objectives: This study is to research delay time comparison for later defibrillation after hands off according to the changes in defibrillation electrodes. Study purpose: In defibrillation treatment that is the only way for cardiac arrest by arrhythmia, it is to find defibrillator device which can minimize late defibrillation delay time after important affect of hands off. Study object and method: After hands off according to the defibrillator device, we collected total 40 people for emergency medicine doctor, internal medicine doctor, general surgeon, nurse, emergency medical technician who are working at 2 CN, CS University hospitals in Gwangju Jeollanamdo district to find out hand off shock interval(HOSI). We then researched their general properties like occupation sector, experiences in clinic, gender, completion of AHA ACLS-P training and more. Then 40 participants continued ventricular fibrillation cardiac arrest simulation training (using human-model mannequin) designed by researcher and performed their roles as defibrillation operator. Each of participant used manual paddle and performed 4 times of defibrillation (150J) during 8 minutes of CPR and in 8day, the defibrillator devices were replaced from manual paddle to self-adhesive electrodes pads and 4 times of defibrillation (150J) under same simulation condition as manual paddle were performed. Study result: In comparison for delay time of later defibrillation after hands off of manual paddle and self adhesive electrodes pad, the self adhesive electrodes pad ($7.0{\pm}0.5sec$) seemed to reduce delay time of later defibrillation significantly (p<0.05) compared to manual paddle ($10.0{\pm}0.9sec$). The self adhesive electrodes pad, according to the general properties of participants, had no particular change in delay time after later defibrillation for the statistics (p>0.05) but the manual paddle had statistically significant differences for the occupation sector, experiences in clinic and gender (p<0.05). Conclusion: In defibrillation, the self adhesive electrodes pad($7.0{\pm}0.5sec$) showed short HOSI compared to manual paddle ($10.0{\pm}0.9sec$) significantly (p<0.05) and it applied identically for both existence and non-existence of ACLS-P training completion, experiences in clinic, gender and occupation sector. The manual paddle had also significant difference in experiences in clinic and occupation sector (p<0.05). which means the effect on HOSI according to the job mastery. Therefore, if the clinic experience is short or in case for the occupations without frequent defibrillation treatment has a danger of lowering success rate for the defibrillation using manual paddle. Therefore, it is true that using self adhesive electrodes pad for defibrillation electrodes when performing manual defibrillation in pre-hospital as well as in-hospital steps can generally minimize delay time of later defibrillation after hands off.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.24
• /
• pp.10659-10663
• /
• 2015

Background: Rapamycin is an effective anti-angiogenic drug. However, the mode of its action remains unclear. Therefore, in this study, we aimed to elucidate the antitumor mechanism of rapamycin, hypothetically via apoptotic promotion, using MCF-7 breast cancer cells. Materials and Methods: MCF-7 cells were plated at a density of $1{\times}10^5$ cells/well in 6-well plates. After 24h, cells were treated with a series of concentrations of rapamycin while only adding DMEM medium with PEG for the control regiment and grown at $37^{\circ}C$, 5% $CO_2$ and 95% air for 72h. Trypan blue was used to determine the cell viability and proliferation. Untreated and rapamycin-treated MCF-7 cells were also examined for morphological changes with an inverted-phase contrast microscope. Alteration in cell morphology was ascertained, along with a stage in the cell cycle and proliferation. In addition, cytotoxicity testing was performed using normal mouse breast mammary pads. Results: Our results clearly showed that rapamycin exhibited inhibitory activity on MCF-7 cell lines. The $IC_{50}$ value of rapamycin on the MCF-7 cells was determined as $0.4{\mu}g/ml$ (p<0.05). Direct observation by inverted microscopy demonstrated that the MCF-7 cells treated with rapamycin showed characteristic features of apoptosis including cell shrinkage, vascularization and autophagy. Cells underwent early apoptosis up to 24% after 72h. Analysis of the cell cycle showed an increase in the G0G1 phase cell population and a corresponding decrease in the S and G2M phase populations, from 81.5% to 91.3% and 17.3% to 7.9%, respectively. Conclusions: This study demonstrated that rapamycin may potentially act as an anti-cancer agent via the inhibition of growth with some morphological changes of the MCF-7 cancer cells, arrest cell cycle progression at G0/G1 phase and induction of apoptosis in late stage of apoptosis. Further studies are needed to further characterize the mode of action of rapamycin as an anti-cancer agent.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.4
• /
• pp.1652-1662
• /
• 2013

As smart devices like smartphones and smart pads are prevalent recently, dramatic changes so called 'smart evolution' deployed in many socioeconomic areas. These changes lead the TV industry to develop a smart TV differentiated from a conventional TV by enabling internet connectivity and applications execution. In this study the factors affecting the acceptance of a smart TV are extracted by reviewing the previous works and the structural relationships among these factors are analyzed. Adding 'Social Influence' to consider an environmental factor and 'Innovativeness' for personal characteristics, we build an extended Technology Acceptance Model and analyzed the structural relationships among the factors in the model using Structural Equation Model. In the results we can find that the environmental factors affect the perceived characteristics. The moderating effects of gender and level of experience in smart devices have also been investigated. No difference is found between gender groups. In much-experienced group, Innovativeness affects Perceived Usefulness and acceptance of a smart TV. In less-experienced group, however, Innovativeness affects Perceived Ease of Use, Expected Enjoyment and finally acceptance of a smart TV.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.3
• /
• pp.49-57
• /
• 2016

This study intended to analyze reinforcement effects of PSC I girder bridges to which prestresses are introduced using V type of external strands. So that series of bridge loading tests are carried out on existing PSC I girder bridge for the cases of before-reinforcement and reinforcement. The measured results from tests being analyzed and compared with the ones from MIDAS structural analyzing program, the reinforcing effects of the reinforcement system adopted in this study were investigated. It is found out that when the V type systems are applied to the bridge girders, the slope of load distribution factor curves become lower improving soundness of bridge upper structure. And also it is confirmed that the reinforcement system in this study can be taken as helpful for improvement of both flexural and shear ability of PSC I girder bridges, as well as dynamic behavior. Furthermore it is found when the elastic pads are applied to the system, dynamic reinforcing effects are maximized.

• Information Systems Review
• /
• v.18 no.2
• /
• pp.151-171
• /
• 2016

With the widespread adoption of mobile devices, such as smart phones and smart pads, as well as the rapid growth of mobile technologies, consumer shopping patterns are changing. This study investigates key factors of consumer purchasing intention in a mobile shopping mall context by incorporating trust belief into the theory of planned behavior. We posit perceived usefulness, perceived enjoyment, perceived ease of use, and trust belief as antecedents of behavioral attitude toward mobile shopping malls. Moreover, social influence and security are identified as key enablers of trust belief on mobile shopping malls. Data collected from 154 consumers with purchasing experience in mobile shopping malls are empirically tested against a research model using partial least squares. Analysis results show that behavioral attitude and perceived behavioral control significantly influence purchasing intention. Moreover, this study reveals the significant effects of perceived usefulness and perceived enjoyment on behavioral attitude. Trust belief indirectly influences purchasing intention through behavioral attitude and is significantly affected by social influence. Understanding consumer purchasing decision-making processes in mobile shopping malls can help service providers to develop effective marketing and operation strategies and campaigns.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.5
• /
• pp.475-479
• /
• 2012

We present a novel polymer fabrication process involving direct UV patterning of a hyperbranched polymer, AEO3000. Compared to PDMS, which is the most widely used polymer in bioMEMS devices, the present polymer has advantages with regard to electrode integration and fast fabrication. We designed a four-chip microelectrofluidic bench having three electrical pads and two fluidic I/O ports. We integrated a microfluidic mixer and a cell separator on the bench to characterize the interconnection performance and sample manipulation. Electrical and fluidic characterization of the microfluidic bench was performed. The measured electrical contact resistance was $0.75{\pm}0.44{\Omega}$, which is small enough for electrical applications, and the pressure drop was 8.3 kPa, which was 39.3% of the value in the tubing method. By performing yeast mixing and a separation test in the integrated module on the bench, we successfully showed that the interconnected chips could be used for bio-sample manipulation.

• Korean Journal of Food Science and Technology
• /
• v.44 no.3
• /
• pp.350-355
• /
• 2012

This study investigated the physiological effects of three species of Auricularia known as Auricularia polytricha (JNM21001), Auricularia auricula-judae black (JNM21002), and Auricularia auricula-judae brown (JNM21012). In the ORAC assay, Auricularia spp. showed antioxidant activities in the order of JNM21001>JNM21012>JNM21002. All Auricularia spp. strongly inhibited the action of ${\alpha}$-amyloglucosidase up to 60%. In order to further test in vivo anti-obesity effects, high fat diet induced ICR obese mice fed a diet containing 20% fat were used. All Auricularia spp. supplementation during high fat diet feeding significantly reduced body weight gain, epididymal fat pads weight, and lowered the food efficiency ratio compared to the high fat control (HFC) group. In particular, the group fed with JNM21012 had a lower average daily body weight gain of 0.45 g/day, demonstrating similar levels to the normal diet fed group. The group fed with JNM21012 significantly reduced lowered serum triglycerides (42%), total cholesterol (81%), and LDL-cholesterol level (66%) compared with the HFC group.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.1
• /
• pp.60-68
• /
• 2016

This paper presents a 6~18 GHz 7-bit digital-controlled attenuator. The proposed attenuator is based on switched-T architecture, but no inductor is used for minimum chip size. The designed attenuator was fabricated using $0.18{\mu}m$ CMOS process, and characterized using on-wafer testing setup. The resolution(minimum attenuation step) and the maximum attenuation range of the attenuator were measured to be 0.22 dB and 28 dB, respectively. The measured RMS attenuation error and the RMS phase error for 6~18 GHz were less than 0.26 dB and $3.2^{\circ}$, respectively. The reference state insertion loss was less than 12.4 dB at 6~18 GHz. The measured input and output return losses were better than 9.4 dB over all frequencies and attenuation states. The chip size is $0.11mm^2$ excluding pads.