• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.969-972
• /
• 2000

This paper proposes 1.5V-3GHz CMOS PLL with a new delay cell for operating in high frequency and multi chained two stage VCO to improve phase noise performance. The proposed multi-chained architecture is able to reduce a timing jitter or a transition spacing and the newly VCO is operating in high frequency. The PFD circuit designed to prevent fluctuation of charge pump circuit under the locking condition. Simulation results show that the tuning range of proposed VCO is wide at 1.8GHz-3.2Ghz and power dissipation is 0.6mW.

• Korean Journal of Optics and Photonics
• /
• v.11 no.5
• /
• pp.330-334
• /
• 2000

A new pha~e lock loop (PLL) IS proposed and demonstrated fat clock recovery from 40 Gblt/s time-dIvision-multiplexed (TDM) optical pulse tri.lin, The proposed clock lecovery scheme lmproves the Jitter effecl cOlmng from the clock. pulse laser of harmonically-mode locked flber laser The cross-corrdation frequency component between the optical Signa] and an optical clock pulse tram is deteCled as a fonr-wave-mixing (FWM) SIgnal generated in SOA. The lock-in freqnency range of the clod. recovery IS found to be within 10 KHz. 0 KHz.

• The Journal of the Korea Contents Association
• /
• v.10 no.2
• /
• pp.72-80
• /
• 2010

The 1Gbps clock and data recovery (CDR) circuit using the proposed multi-point phase detector (PD) is presented. The proposed phase detector generates up/down signals comparing 3-point that is data transition point and clock rising/falling edge. The conventional PD uses the pulse width modulation (PWM) that controls the voltage controlled oscillator (VCO) using the width of a pulse period's multiple. However, the proposed PD uses the pulse number modulation (PNM) that regulates the VCO with the number of half clock cycle pulse. Therefore the proposed PD can controls VCO preciously and reduces the jitter. The CDR circuit is tested using 1Gbps $2^{31}-1$ pseudo random bit sequence (PRBS) input data. The designed CDR circuit shows that is capable of recovering clock and data at rates of 1Gbps. The recovered clock jitter is 7.36ps at 1GHz and the total power consumption is about 12mW. The proposed circuit is implemented using a 0.18um CMOS process under 1.8V supply.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.2
• /
• pp.72-77
• /
• 2009

In this paper, a 3.2Gb/s clock and data recovery (CDR) circuit for a high-speed serial data communication without the reference clock is described This CDR circuit consists of 5 parts as Phase and frequency detector(PD and FD), multi-phase Voltage Controlled-Oscillator(VCO), Charge-pumps (CP) and external Loop-Filter(KF). It is adapted the PD and FD, which incorporates a half-rate bang-bang type oversampling PD and a half-rate FD that can improve pull-in range. The VCO consists of four fully differential delay cells with rail-to-rail current bias scheme that can increase the tuning range and tuning linearity. Each delay cell has output buffers as a full-swing generator and a duty-cycle mismatch compensation. This materialized CDR can achieve wide pull-in range without an extra reference clock and it can be also reduced chip area and power consumption effectively because there is no additional Phase Locked- Loop(PLL) for generating reference clock. The CDR circuit was designed for fabrication using 0.18um 1P6M CMOS process and total chip area excepted LF is $1{\times}1mm^2$. The pk-pk jitter of recovered clock is 26ps at 3.2Gb/s input data rate and total power consumes 63mW from 1.8V supply voltage according to simulation results. According to test result, the pk-pk jitter of recovered clock is 55ps at the same input data-rate and the reliable range of input data-rate is about from 2.4Gb/s to 3.4Gb/s.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.5
• /
• pp.1103-1108
• /
• 2010

In this paper, Frequency Synthesizer which is widely used for FH-SS system is proposed and the experimental results are analyzed. The performance of the DPLL(Digital Phase-Locked-Loop), which is the main part of the Synthesizer is analyzed by the computer program. Using Maxplus-II tool provided by altera. co., ltd, each part of the DPLL is designed and all of them is integrated into EPM7064SLC44-10 chip. And the simulation results are compared with the characteristics of the implemented circuits for analysis. And the experiential results show that the N value of the loop filter is toggled to adjacent N value, which result in phase jitter of the output. It can be resolved by increasing DCO(Digital Controlled oscillator) clock rate.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.110-116
• /
• 2016

This paper describes 1.2-V 5-Gb/s scalable low voltage signaling(SLVS) differential transmitter(TX) with a digital impedance calibration and equalizer. The proposed transmitter consists of a phase-locked loop(PLL) with 4-phase output clock, a 4-to-1 serializer, a regulator, an output driver, and an equalizer driver for improvement of the signal integrity. A pseudo random bit sequence generator is implemented for a built-in self-test. The proposed SLVS transmitter provides the output differential swing level from 80mV to 500mV. The proposed SLVS transmitter is implemented by using a 65-nm CMOS with a 1.2-V supply. The measured peak-to-peak time jitter of the implemented SLVS TX is about 46.67 ps at the data rate of 5Gb/s. Its power consumption is 1.88 mW/Gb/s.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.5
• /
• pp.45-53
• /
• 2007

To recover transmitted signal perfectly at DTV receiver, we have to acquire carrier frequency synchronization to compensate pilot signal which located in wrong position and rotated phase. Also, we need a symbol timing synchronization to compensate sampling timing error. Conventionally, to synchronize symbol timing, we use Gardner's scheme which used in multi-level signal. Gardner's scheme is well known for its sampling the timing error signal from every symbol and it makes easy to detect and keep timing sync in multi-path channel. In this paper, to discuss the problem when the received power level is out of range and we cannot get synchronization information. With this problem, we use 2 step procedures. First, we put a received signal power compensation block before Garder's timing error detector. Second, adaptive loop filter to get a fast synchronization information and averaging loop filter's output value to reduce the amount of jitter after synchronization in PLL(Phased Locked Loop) circuit which is used to get a carrier frequency synchronization and symbol timing synchronization. Using the averaging value, we can estimate offset. Based on offset changing ratio, we can adapt adaptive loop filter to carrier frequency and symbol timing synchronization circuit.