• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.411.1-411.1
• /
• 2016

In this study, we examined the effects of boron doping on the dielectric reliability of solution processed aluminum oxide ($Al_2O_3$). When boron is doped in aluminum oxide, the hysteresis reliability is improved from 0.5 to 0.4 V in comparison with the undoped aluminum oxide. And the accumulation capacitance is increased when boron was doped, which implying the reduction of the thickness of dielectric film. The improved dielectric reliability of boron-doped aluminum oxide is originated from the small ionic radius of boron ion and the stronger bonding strength between boron and oxygen ions than that of between aluminum and oxygen ions. Strong boron-oxygen ion bonding in aluminum oxide results dielectric film denser and thinner. The leakage current of aluminum oxide also reduced when boron was doped in aluminum oxide.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.687-694
• /
• 2008

This paper is focused on the improvement of MOS device reliability related to deuterium process. The injection of deuterium into the gate oxide film was achieved through two kind of method, high-pressure annealing and low-energy implantation at the back-end of line, for the purpose of the passivation of dangling bonds at $SiO_2/Si$ interface. Experimental results are presented for the degradation of 3-nm-thick gate oxide ($SiO_2$) under both negative-bias temperature instability (NBTI) and hot-carrier injection (HCI) stresses using P and NMOSFETs. Annealing process was rather difficult to control the concentration of deuterium. Because when the concentration of deuterium is redundant in gate oxide excess traps are generated and degrades the performance, we found annealing process did not show the improved characteristics in device reliability, compared to conventional process. However, deuterium ion implantation at the back-end process was effective method for the fabrication of the deuterated gate oxide. Device parameter variations under the electrical stresses depend on the deuterium concentration and are improved by low-energy deuterium implantation, compared to conventional process. Our result suggests the novel method to incorporate deuterium in the MOS structure for the reliability.

• Journal of the Korean Ceramic Society
• /
• v.31 no.1
• /
• pp.74-78
• /
• 1994

Degradation of thin oxide by doped poly-Si and its improvement were studied. The gate oxide can be degraded by phosphorous in poly-Si doped POCl3. The degradation is increased with the decrement of sheet resistance and poly-Si thickness. Oxide failures of amorphous-Si are higher than those of poly-Si. In-situ double deposition of amorphous-Si, 54$0^{\circ}C$/30 nm, and poly-Si, 6$25^{\circ}C$/220 nm, forms the mismatch structure of grain boundary between amorphous-Si and poly-Si, and suppresses the excess phosphorous on oxide surface by the mismatch structure. The control of phosphorous through grain boundary improves the oxide reliability.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.421-424
• /
• 2004

As the deep sub-micron devices are recently integrated high package density, novel process method for sub $0.1{\mu}m$ devices is required to get the superior thin gate oxide characteristics and reliability. However, few have reported on the electrical quality and reliability on the thin gate oxide. In this paper I will recommand a novel shallow trench isolation structure for thin gate oxide $30{\AA}$ of deep sub-micron devices. Different from using normal LOCOS technology, novel shallow trench isolation have a unique 'inverse narrow channel effects' when the channel width of the devices is scaled down shallow trench isolation has less encroachment into the active device area. Based on the research, I could confirm the successful fabrication of shallow trench isolation(STI) structure by the SEM, in addition to thermally stable silicide process was achiever. I also obtained the decrease threshold voltage value of the channel edge and the contact resistance of $13.2[\Omega/cont.]$ at $0.3{\times}0.3{\mu}m^2$. The reliability was measured from dielectric breakdown time, shallow trench isolation structure had tile stable value of $25[%]{\sim}90[%]$ more than 55[sec].

• IE interfaces
• /
• v.20 no.1
• /
• pp.87-93
• /
• 2007

Burn-in is an engineering method for screening out products containing reliability defects which would cause early failures in field operation. Previously, various burn-in models have been proposed mainly focused on the trade-off of shop repair cost and warranty cost ignoring manufacturing yield. From the view point of a manufacturer, however, burn-in decreases warranty cost at the expense of yield reduction. In this paper, we provide a general model quantifying a trade-off between product yield and reliability, in which any defect distribution from previous yield models can be used. A profit function is expressed in burn-in environments for determining an optimal burn-in time. Finally, the method is illustrated with gate oxide failures which is an important reliability concerns for VLSI CMOS circuits.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.11
• /
• pp.105-112
• /
• 1993

Oxide and reoxidized-nitrided-oxide were formed by furnace oxidation and rapid thermal processing (RTP). MOS capacitor and n-MOSFET's with those films as gate insulators were fabricated. The electrical characteristics of insulators were evaluated by current-voltage, high-frequency capacitance-voltage (C-V), and time-dependent dielectrical breakdown (TDDB) measurements. The hot carrier effects of MOSFET's were also investigated. Time-dependent dielectrical breakdown (TDDB) characteristics show that the life time of reoxidized-nitrided-oxide films is about 3 times longer than that of oxides. Hot carrier effects reveal that the life time of MOSFET's with reoxidized-nitrided-oxides is about 3 times longer than that of MOSFET's with oxides. Therefore, it is found that the reliability of dielectric films estimated by the hot carrier effects of MOSFET's is consistent with that of dielectric films from TDDB method.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.6
• /
• pp.43-49
• /
• 1997

Tungsten poycide has studied gate oxide reliability and dielectric strength charactristics as the composition of gate electrode which applied submicron on CMOS and MOS device for optimizing gate electrode resistivity. The gate oxide reliability has been tested using the TDDB(time dependent dielectric breakdwon) and SCTDDB (stepped current TDDB) and corelation between polysilicon and WSi$_{2}$ layer. iN the case of high intrinsic reliability and good breakdown chracteristics on polysilicon, confirmed that tungsten polycide layer is a better reliabilify properities than polysilicon layer. Also, hole trap is detected on the polysilicon structure meanwhile electron trap is detected on polycide structure. In the case of electron trap, the WSi$_{2}$ layer is larger interface trap genration than polysilicon on large POCL$_{3}$ doping time and high POCL$_{3}$ doping temperature condition. WSi$_{2}$ layer's leakage current is less than 1 order and dielectric strength is a larger than 2MV/cm.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.6
• /
• pp.117-127
• /
• 1994

In this paper, electrical and reliability properties of N$_2$O oxides, grown at the temperature of 95$0^{\circ}C$ and 100$0^{\circ}C$ to 74$\AA$, and 82$\AA$. respectively, using NS12TO gas in a conventional furnace, have been compared with those of pure oxide grown at the temperature of 850 to 84$\AA$ using O$_2$ gas. Initial IS1gT-VS1gT characteristics of N$_2$O oxides were similar to those of pure oxide, and reliability properties of N$_2$O oxides, such as charge trapping, interface state density and leakage current at low electric field under F-N stress, were improved much better than those of pure oxide. But, with increasing capacitor area. TDDB characteristics of N$_2$O oxides were more degraded than those of pure oxide and this degradation of TDDB characteristics was more severe in 100$0^{\circ}C$ N$_2$Ooxide than in 95$0^{\circ}C$ N$_2$O oxide. The improvement of reliability properties excluding TDDB in N$_2$Ooxides was attributed to the hardness of the interface improved by nitrogen pile-up at the interface of Si/SiO$_2$, but on the other hand, the degradation of TDDB characteristics in N$_2$O oxides was obsered due to the increase of local thinning spots caused by excessive nitrogen at interface during the growth of N$_2$O oxides.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.05a
• /
• pp.37-38
• /
• 1993

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.11
• /
• pp.996-1000
• /
• 2005

Experimental results are presented for the degradation of 3 nm-thick gate oxide $(SiO_2)$ under both Negative-bias Temperature Instability (NBTI) and Hot-carrier-induced (HCI) stresses using P and NMOSFETS, The devices are annealed with hydrogen or deuterium gas at high-pressure $(1\~5\;atm.)$ to introduce higher concentration in the gate oxide. Both interface trap and oxide bulk trap are found to dominate the reliability of gate oxide during electrical stress. The degradation mechanism depends on the condition of electrical stress that could change the location of damage area in the gate oxide. It was found the trap generation in the gate oxide film is mainly related to the breakage of Si-H bonds in the interface or the bulk area. We suggest that deuterium bonds in $SiO_2$ film are effective in suppressing the generation of traps related to the energetic hot carriers.