• 한국전자파학회논문지
• /
• 제29권11호
• /
• pp.857-867
• /
• 2018

현재 레이다의 발전 형태는 기존의 능동위상배열에서 디지털형 위상배열로 진화하고 있다. 디지털형 위상배열은 수신빔을 자유롭게 구성할 수 있는 장점이 있다. 이를 가능하게 하려면 각각의 복사소자별 수신신호가 디지털화되어야 한다. 본 논문에서는 이를 위한 디지털 송수신모듈을 설계 및 제작하고 시험결과를 제시하여 가능성을 확인하고자 한다. 디지털 송수신모듈은 4개의 송수신 채널을 포함한 쿼드팩 형태로 구성하였다. 고출력 송신을 위해 각 채널별로 GaN 소재의 고출력증폭소자(HPA)를 사용하였으며, 송신파형 발생과 수신신호 디지털변환을 위해 송수신 집적소자를 적용한 디지털 회로를 적용하였다. 제작한 결과, 각 채널별로 송신출력은 350 W 이상, 수신이득은 47 dB, 수신잡음지수 2 dB 이하를 만족하였다. 또한 모듈 내에서 최종 광신호로 변환된 수신출력을 저장하고, 분석하여 수신 특성을 확인하였다.

• 한국전자파학회논문지
• /
• 제25권12호
• /
• pp.1243-1250
• /
• 2014

본 논문에서는 0.5~1.1 GHz 주파수 범위를 갖는 광대역 DDS(Direct Digital Synthesizer) 모듈의 설계 및 제작 결과에 대해 기술하고자 한다. 600 MHz 대역폭을 갖는 광대역 DDS 구현을 위해 DDS의 클럭을 2.4 GHz로 선정하였다. 광대역 DDS의 불요신호(spurious) 특성을 개선하기 위해 출력 불요신호 대비 크기가 같고, 역위상을 갖는 여러 개의 신호들을 동시에 발생시킨 후 DDS 내부에서 출력 신호와 합성하였다. 제작된 DDS 모듈의 불요신호는 상용 DDS 대비 10 dB 정도 개선되었고, DDS 모듈의 동조 속도는 340 ns 이하임을 확인하였다.

• 한국전자통신학회논문지
• /
• 제9권12호
• /
• pp.1331-1336
• /
• 2014

본 논문은 X대역 고출력증폭기의 전력 결합 손실을 최소화 하기위하여 Al2O3 박막 기판으로 제작한 divider/Combiner 회로를 X-대역의 PAM(Power Amplifier Module)에 적용하여 25W 급 전력증폭기 모듈을 구현하였다. 제작은 MMIC 칩과 수정된 형태의 10way traveling wave divider/Combiner회로를 사용하였으며 제작된 Traveling wave구조의 전력증폭기는 출력전력 45.2dBm, 16dB 이득, PAE 26 % 특성을 얻었으며 IMD3 는 17dBc@44dBm의 특성을 보였다. 본 연구의 divider/Combiner 회로는 다단계 구조의수동 결합기 및 분배기에 사용될 수있으며 협소한 크기의 전력증폭기에 사용될 수 있다.

• 한국기계가공학회지
• /
• 제14권5호
• /
• pp.134-140
• /
• 2015

A control program of an engine control module (ECM) was developed, and its control performance was verified on a 750Ps marine diesel engine. The control method was designed for an engine rotational speed control system. For ECM hardware, the commercial rapid control prototype (RCP) ECM was used. The programming tool for control algorithm development was the MatLab/Simulink. The main control algorithm assembled many control models as engine cranking, run, and stall. Each model has sub-models to input/output control signals. The target engine speed was input signal from a speed control lever, and control output signal of the ECM was sent to the unit-injectors for fuel injection. The engine test was performed under various conditions of engine rotational speeds and dynamometer loads. The test results show that the control function of the ECM is suitable for electrical marine diesel engines.

• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.533-541
• /
• 2011

The redundant operation of a parallel AC to DC converter via a serial communication bus is presented. The proposed system consists of three isolated CUK power factor correction modules. The controller for each converter is a dsPIC30F6010 microcontroller while a RS485 communication bus and the clock signal are used for synchronizing the data communication. The control strategy of the redundant operation relies on the communication of information among each of the modules, which communicate via a RS485 serial bus. This information is received from the communication checks of the converter module connected to the system to share the load current. Performance evaluations were conducted through experimentation on a three-module parallel-connected prototype, with a 578W load and a -48V dc output voltage. The proposed system has achieved the following: the current sharing is quite good, both the transient response and the steady state. The converter modules can perform the current sharing immediately, when a fault is found in another converter module. In addition, the transient response occurs in the system, and the output voltages are at their minimum overshoot and undershoot. Finally, the proposed system has a relatively simple implementation for the redundant operation.

• 설비공학논문집
• /
• 제27권7호
• /
• pp.375-379
• /
• 2015

A proper estimate of solar cell efficiency is of great importance for the feasibility analysis of solar cell power plant development. Since solar cell efficiency depends on temperature, several methods have been introduced to measure it by operating temperature modulation. However, the methods either rely on the external environment or need expensive equipment. In this paper, a thermoelectric module was used to control the operating temperature of crystalline silicon solar cells effectively and precisely over a wide range. The output characteristics of crystalline silicon solar cells in response to operating temperatures from $-5^{\circ}C$ to $100^{\circ}C$ were investigated experimentally. Their efficiencies decreased as the temperature rose, since the decrease in the open circuit voltage and fill factor exceeded the increase in the short circuit current. The maximum power temperature coefficient of the single crystalline solar cell was more sensitive to temperature change than that of the polycrystalline solar cell.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 추계학술발표대회 논문집
• /
• pp.246-250
• /
• 2009

String & tabbing step in the crystalline PV module manufacturing process for the temperature directly affects solar cells. In fact, in the manufacture of PV modules tend to be temperature factor and the corresponding changes n the output shows the same characteristics. In this journal, it will be considered about thermal characteristics, especially changes of characteristic in high temperature of the solar cell through experiment that we measure electric output characteristics of solar cells after those are applied with high temperature changes for two seconds. And we can think about the possibility of efficiency improvements over looks in PV module manufacturing processes.

• 한국전기전자재료학회논문지
• /
• 제34권6호
• /
• pp.433-437
• /
• 2021

As the demand for new and renewable energy increases due to the depletion of fossil fuels, solar power generation, a core energy source for new and renewable energy, requires research on solar modules for high output power generation. In this paper, the electrical characteristics of solar cell strip at the edge and in the center of single-crystal silicon having a semi-square shape were analyzed. The cell strip located in the center showed the efficiency increase by 0.26% compared to the cell strip at the edge of the solar cell. A shingled photovoltaic module was manufactured for each cell strip. As a result, the output power of the module using the cell strip located in the center was higher by 0.992%.

• Current Photovoltaic Research
• /
• 제7권2호
• /
• pp.51-54
• /
• 2019

The high density module (HDM) has advantages for its larger active area and smaller current density. This new way of making a photovoltaic (PV) module method has benefit for increasing module power with the same installed area. Because HDM consisted with serially connected PV strings, loss of strings during the fabrication process can increase the overall production cost.1-2 This study investigates the rework conditions of the shingled strings with electrically conductive adhesives (ECA). By heating the electrically connected area of a fabricated string, cured area become soft and a string can be detached for the rework process. After rework process, a refabricated string showed 5~10% increased output power compared to before rework process and reached to the 90~95% output power compare to the undamaged strings.

• 한국산업융합학회 논문집
• /
• 제25권3호
• /
• pp.451-459
• /
• 2022

Recently, in accordance with the demand for a large capacity of a secondary battery according to an increase in the demand for energy storage devices, a modular series battery configuration is essential. Accordingly, various cell balancing techniques have been proposed to prevent high efficiency and performance degradation of the battery. In this paper, propose a battery voltage balancing topology consisting of a flyback DC/DC converter type of a SIMO (Single-Input-Multiple Output) two-switch configuration for a series battery configuration. The proposed topology shows a structure in which a DC/DC converter connected to each module and a battery cell share one transformer. The topology cell balancing operation is a principle in which the voltage balancing converter of the battery converges to the same value through a transformer that shares a magnetic flux with the cells constituting the module through a single high-frequency transformer. In this paper, the dynamic characteristics analysis of the proposed circuit using PSIM was based and it was verified through experiments on one module.