• 한국자동차공학회논문집
• /
• 제16권3호
• /
• pp.159-165
• /
• 2008

This paper deals with the optimum high pressure control algorithm for a transcritical $CO_2$ mobile air-conditioning system with belt-driven compressor to achieve the maximum COP. The experiments were performed to find out the maximum COP conditions with various operating conditions. The experimental results showed that the COP was increased and then decreased with increase of the refrigerant high pressure for the system. Therefore the value of high pressure which has maximum COP could be selected. Furthermore, the strong (linear) relation between the optimum high pressure and the gas cooler outlet temperature was revealed, which suggests the use of a simple controller with only one parameter for the transcritical $CO_2$ cycle.

• Journal of Welding and Joining
• /
• 제12권3호
• /
• pp.71-81
• /
• 1994

Laser cutting is experiencing a rising worldwide acceptance in the industry. Expert systems are necessary for the systematic arrangement and searching of experimental data existing in journal papers, job handbooks, etc.. This paper proposes an expert system for the selection of the appropriate laser cutting variables from the available database. Optimum cutting conditions according to the given cutting velocity were searched and qualitative comments which are difficult to be used as database variables were shown at each velocity using the binary and fuzzy inference. These comments could be informative to unskilled operators of the laser cutting process. Typical cutting conditions of the mild steel and stainless steel were included and the working range and quality variations were displayed graphically. The proposed algorithm was implemented in an IBM compatible personal computer as an expert system for CO$_{2}$ laser cutting to derive the optimum cutting conditions by using the turbo prolog.

• 한국정밀공학회지
• /
• 제15권6호
• /
• pp.145-152
• /
• 1998

This paper presents an optimum design of a rotor-bearing spindle system for a ultra centrifuge (80,000 RPM) supported by ball bearings with nonlinear stiffness characteristics. To obtain the nonlinear bearing stiffnesses, a ball bearing is modeled in five degrees of freedom and is analyzed quasi-statically. The dynamic behaviors of the nonlinear rotor-bearing system are analyzed by using a transfer-matrix method iteratively. For optimization. we use the cost function that simultaneously minimizes the weight of a rotor and maximizes the separation margins to yield the critical speeds as far from the operating speed as possible. Augmented Lagrange Multiplier (ALM) method is employed for the nonlinear optimization problem. The result shows that the rotor-bearing spindle system is optimized to obtain 9.5％ weight reduction and 21％ separation margin.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 춘계학술대회 논문집
• /
• pp.7-34
• /
• 1994

;Recently the sheet forming simulation technology revealed great progress in the sense of practical application in the automotive, electric/electronics and aviation/space industries. The goal of sheet forming simulation is to embedded in the design engineering system which is consisted by the analysis and synthesis modules. This design simulation system predicts the slackness of sheet and estimate the formability, and search the optimum material/forming/structure conditions. This OVER-ALL OPTIMUM DESIGN can be classified as follow; 1. ANALYZING PROCEDURE: Numerical simulation based on nonlinear theories -geometry, material and friction nonlinearities- 2. OPTIMIZATION PROCEDURE: Optimum design based on mathematical programing and AI technologies, those are implemented in CAD/CAM/CAE System - Concurrent Engineering System-. In this paper, four subjects will be discussed; (1) State of arts of computer simulation technologies in Japan. (2)History of sheet forming simulation. (3) Benchmark problems. (4) Future technology in the sheet forming simulation.ation.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.84-87
• /
• 2008

In order to maximize the effect of installing screen door system while to minimize the problems in an initial stage of introduction, it is strongly required to research an optimum installation solution in connection with ventilation and disaster prevention system alongside with safety structure analysis of screen door in respect to train-induced wind, as well as to develop the criteria for the operation after the installation. This paper presents the results of study to develop the optimum design technology in urban railway equipped with platform screen door systems.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.853-855
• /
• 1993

In this paper, a further improved system obtaining very low distorted waveforms of input ac currents of three phase rectifier circuit is proposed. The proposed system consists of an uncomplicated 24 pulse diode bridge rectifier that is transformerless, by adding only switching circuit which consists of two switchs to conventional system. Also to optimum the effectiveness or the harmonic reduction, the optimum turn ratio of an autotransformer and the optimum switching control angle are decided by computer simulation. And then, the voltage waveform obtained has a total harmonic distortion of 8.1%, and the predominant harmonics 23th and 25th. This paper describes operation principle, analysis of the waveforms of input voltage and current. The theoretial results are verified through simulation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제13권1호
• /
• pp.69-76
• /
• 1989

This paper presents a method of the optimum design for rotating shaft of centrifugal pump. That is, the object is to optimize the system in stability at the operating speed, unbalance response in the vicinity of the rotor critical speed, leakage flow of the seals. The objective function is composed of these three elements and is minimized by changing seal cleareance, diamoters, and lengths. A typical double suction centrifugal pump is analyzed and its objective function is presented. Then the optimum dimensions of seals are obtained, and vibration characteristics at both initial and optimum conditions are investigated.

• 대한기계학회논문집A
• /
• 제27권5호
• /
• pp.758-763
• /
• 2003

A profile shifted gear system was analyzed to select the optimum profile shift coefficient, which minimizes gear teeth deflection. Contact force and deformation overlap were calculated by means of FEM and contact theory. The deformation overlap is suggested for an effective indicator to represent the whole deformation of gear system. The optimum value of profile shift coefficients was presented with respect to the deformation of gear system.

• 산업경영시스템학회지
• /
• 제17권32호
• /
• pp.221-226
• /
• 1994

Almost preventive maintenance policies assumed that the system after pm has failure rate as before pm with probability p and as good as new with probability 1-p. This paper considers the s-expected cost of the model with imperfect periodic preventive maintenance that increasing minimal repair costs at failure and obtains the optimum periodic preventive maintenance time. Numerical example are shown in which the failure time of the system has gamma distribution.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.742-745
• /
• 1993

In this paper, instantaneous current tracking control inverter is applied to photovoltaic system and then optimum operating area is described by state space average method for optimum design of maximum output control. Also control system is realized by DSP and excellence of system shows the effectiveness of inverter system using the instantaneous control method.