• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.4
• /
• pp.154-158
• /
• 2021

The optical transmittance of Mn-doped SnO₂ monolayer film increased gradually from 80.9 to 85.4 % at 550 nm wavelengths upon increasing the O₂/Ar+O₂ concentration rate from 0 to 7.9 % and the band gap energy changed from 3.0 to 3.6 eV. The resistivity tended to decrease from 3.21 Ω·cm to 0.03 Ω·cm, reaching a minimum at 2.7 %, and then gradually increased from 0.03 to 52.0 Ω·cm at higher O₂/Ar+O₂ gas concentration ratio. Based on XPS spectra analysis, the Sn 3d_5/2 peak of Mn-doped SnO₂ single layer shifted slightly from 486.40 to 486.58 and O_1s peak also shifted from 530.20 to 530.33 eV with increase the O₂/Ar+O₂ concentration ratio. Therefore, the XPS spectra results indicate that a multiphase with SnO and SnO₂ coexisted in the sputtered Mn-doped SnO₂ monolayer film.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.157-160
• /
• 2021

As an insulator for a thin film transistor(TFT) and an encapsulation material of organic light emitting diode(OLED), aluminum oxide (Al₂O₃) has been widely studied using several technologies. Especially, in spite of low deposition rate, atomic layer deposition (ALD) has been used as a process method of Al₂O₃ because of its low process temperature and self-limiting reaction. In the Al₂O₃ deposition by ALD method, Ar Purge had some crucial effects on the film properties. After reaction gas is injected as a formation of pulse, an inert argon(Ar) purge gas is injected for gas desorption. Therefore, the process parameter of Ar purge gas has an influence on the ALD deposited film quality. In this study, Al₂O₃ was deposited on glass substrate at a different Ar purge time and its structural characteristics were investigated and analyzed. From the results, the growth rate of Al₂O₃ was decreased as the Ar purge time increases. The surface roughness was also reduced with increasing Ar purge time. In order to obtain the high quality Al₂O₃ film, it was known that Ar purge times longer than 15 sec was necessary resulting in the self-limiting reaction.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.2
• /
• pp.90-94
• /
• 2015

In this study, the characterizations of oxide contact hole etching are investigated with C₄F₈/O₂/Ar and CH₂F₂/C₄F₈/O₂/ Ar plasma. As the percent composition of C₄F₈ in a C₄F₈/O₂/Ar mixture increases, the amount of polymer deposited on the etched surface also increases because the C_xF_y polymer layer retards the reaction of oxygen atoms with PR. Adding CH₂F₂ into the C₄F₈/O₂/Ar plasma increases the etch rate of the oxide and the selectivity of oxide to PR. The profile of contact holes was close to 90°, and no visible residue was seen in the SEM image at a C₄F₈/(C₄F₈+O₂) ratio of 58%. The changes of chemical composition in the chamber were analyzed using optical emission spectroscopy, and the chemical reaction on the etched surface was investigated using X-ray photoelectron spectroscopy.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.388-392
• /
• 2002

In this work, the etching of $CeO_2$ thin films has been performed in an inductively coupled $Ar/CF_4/Cl_2$ plasma. The highest etch rate of the $CeO_2$ thin film ws 250 ${\AA}/min$ and the selectivity of CeO$_2$to SBT was 0.4 at a 10% additive $Cl_2$ into Ar/($Ar+CF_4$)gas mixing ratio of 0.8. From result of X-ray photoelectron spectroscopy (XPS) analysis, there are Ce-Cl and Ce-F bonding by chemical reaction between Cl, F and Ce. During the etching of $CeO_2$ thin films in $Ar/CF_4/Cl_2$ plama, Ce-Cl and Ce-F bond is formed, and these prodcuts can be removed by the physical bombardment of Ar ions. The 10% additive $Cl_2$ into the Ar/($Ar+CF_4$)gas mixing ratio of 0.8 could enhance the reaction between Cl, F and Ce.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.4
• /
• pp.317-321
• /
• 2003

In this study, the structural properties were Investigated for the deposited (Ba,Sr)(Nb,Ti)O$_3$[BSNT] thin films grown on Pt/TiO$_2$/SiO$_2$/Si substrate by RF sputtering method. The structural properties of the BSNT thin films affected by the Ar/02 ratios were Investigated. In the case of the BSNT thin films deposited with condition of 60/40(Ar/O$_2$) ratio, the BaTiO$_3$, SrTiO$_3$ and BaNbO$_3$ phases were showed. The composition ratio of Nb and Ti in the BSNT thin films were nearly equivalent. Also, in the BSNT thin films deposited with condition of 60/40 and 80/20(Ar/O$_2$) ratios, the composition of Ba, Sr, Nb and Ti were relatively uniform. The Ba, Sr, Nb and Ti in the BSTN thin films were not diffused into the Pt layer.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.2
• /
• pp.43-52
• /
• 2021

The Ni-based superalloy, Inconel 740, was corroded between 800 and 1100℃ for up to 100 hr in air and Ar-0.2%SO₂ gas in order to study its corrosion behavior in air and sulfur/oxygen environment. It displayed relatively good corrosion resistance in both environment, because its corrosion was primarily dominated by not sulfidation but oxidation especially in Ar-0.2%SO₂ gas. Such was attributed to the thermodynamic stability of oxides of alloying elements when compared to corresponding sulfides. The scales consisted primarily of Cr₂O₃, together with some NiAl₂O₄, MnCr₂O₄, NiCrMnO₄, and rutile-TiO₂. Sulfur from SO₂ gas made scales prone to spallation, and thicker. It also widened the internal corrosion zone when compared to air. The corrosion resistance of IN740 was mainly indebted to the formation of protective Cr₂O₃-rich oxides, and suppression of the sulfide formation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.276-279
• /
• 2011

This work, the etching characteristics of $Ba_2Ti_9O_{20}$(BTO) thin films were investigated using an inductively coupled plasma (ICP) of $Ar/Cl_2$ gas mixture. The etch rate of BTO thin films as well as the $BTO/SiO_2$ and BTO/PR etch selectivity were measured as functions of $Ar/Cl_2$ mixing ratio (0~100% Ar) at a constants gas pressure (6 mTorr), total gas flow rate (50 sccm), input power (700 W) and bias power (200 W). The etch rate of BTO thin films decreased with increasing Ar fraction. To analyze the etching mechanism an optical emission spectroscopy (OES), double Langmuir probe(DLP) and surface analysis using X-ray photoelectron spectroscopy (XPS) were carried out.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1165-1169
• /
• 2003

The Ta$_2$O$_{5}$ thin film was deposited on Si-(III) and glass substrate with the change of Ar:O$_2$ gas flow rate in the assist ion gun by the Dual ion-Beam Sputtering (DIBS). As the $O_2$ gas flow of the assist ion gun was decreased, the deposition rate of the thin films decreased. The refractive index was fixed (2.11, at 1550 nm) without regarding to $O_2$ gas flow of the range 3∼12 sccm in assist ion gun. The condition of Ar:O$_2$=3:12 was formatted stoichiometry composition of Ta$_2$O$_{5}$ and the ms roughness was small (0.183 nm).

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.240-240
• /
• 2015

본 논문에서는 플라즈마 모델링과 식각 표면 분석을 통해 가스 비율 변화에 따른 $CF_4/C_4F_8/Ar$ 유도결합 플라즈마의 특성과 Si 및 $SiO_2$의 식각 메커니즘에 대해 연구하였다.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.5
• /
• pp.29-35
• /
• 1999

Inductively coupled plsama etching of platinum thin film was studied using $O_2$ addition to $Cl_2$/Ar gas plasma. In this study, Pt etching mechanism was investigated with Ar/$Cl_2$ /$O_2$ gas plasma by using XPS and QMS. Ion current density was measured with Ar/$Cl_2$ /$O_2$ gas plasma by using single Langmuir probe. It was confirmed by using QMS and single Langmuir probe that Cl and Ar species rapidly decreased and ion current density was also decreased with increasing $O_2$ gas ratios. These results implied that the decrease of Pt etch rate is due to the decrease of reactive species ans ion current density with increasing $O_2$ gas mixing ratios. A maximum etch rate of 150nm/min and the oxide selectivity of 2.5 were obtained at Ar/$Cl_2$ /$O_2$ flow rate of 50 seem, RF power of 600 W, dc bias voltage of 125 V, and the total pressure of 10 mTorr.