• Journal of Powder Materials
• /
• v.26 no.3
• /
• pp.220-224
• /
• 2019

The aluminum (Al)/copper oxide (CuO) complex is known as the most promising material for thermite reactions, releasing a high heat and pressure through ignition or thermal heating. To improve the reaction rate and wettability for handling safety, nanosized primary particles are applied on Al/CuO composite for energetic materials in explosives or propellants. Herein, graphene oxide (GO) is adopted for the Al/CuO composites as the functional supporting materials, preventing a phase-separation between solvent and composites, leading to a significantly enhanced reactivity. The characterizations of Al/CuO decorated on GO(Al/CuO/GO) are performed through scanning electron microscopy, transmission electron microscopy, and energy dispersive X-ray spectroscopy mapping analysis. Moreover, the functional bridging between Al/CuO and GO is suggested by identifying the chemical bonding with GO in X-ray photoelectron spectroscopy analysis. The reactivity of Al/CuO/GO composites is evaluated by comparing the maximum pressure and rate of the pressure increase of Al/CuO and Al/CuO/GO. The composites with a specific concentration of GO (10 wt%) demonstrate a well-dispersed mixture in hexane solution without phase separation.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.731-739
• /
• 2014

Aluminum and boron co-doped zinc-oxide(AZOB) powders as transparent conducting oxide(TCO) were prepared by spray pyrolysis at $900^{\circ}C$. The micron-sized AZOB particles were prepared by spray pyrolysis from aqueous precursor solutions for aluminium, boron, and zinc. The micron-sized AZOB particle after the spray pyrloysis underwent post-heat treatment at $700^{\circ}C$ for 2 hours and it was changed fully to nano-sized AZOB particle by ball milling for 24 hours. The size of primary AZOB particle by Debye-Scherrer Equation and surface resistance of AZOB pellet were measured.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.6
• /
• pp.220-225
• /
• 2020

Gallium oxide nano-powder, the key starting material for IGZO target, is fabricated by gas phase synthesis using a new apparatus consist of reaction, transportation, and collection parts. As a result of gallium metal evaporation above 1150℃, Ga2O3 nano-powders, are successfully synthesized. The SEM images of the synthesized powders displace the spherical shaped powders without severe agglomeration. X-ray diffraction and PSA analysis show that the higher temperature at the reaction part results in the better crystallinity and larger powder size of the synthesized Ga2O3. To see the applicability to IGZO target, Ga2O3 nano-powders synthesized at 1250℃ are mixed with indium oxide and zinc oxide (In2O3 : Ga2O3 : ZnO = 1 : 1 : 1), and then sintered at 1400~1500℃. The highest sintered density of 5.83 g/㎤ (= 91 % of relative density) is achieved when sintered at 1450℃, showing better sinterability compared to the commercially available Ga2O3 powder, which has 5.61 g/㎤ of sintered density at the same condition.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.9
• /
• pp.1381-1385
• /
• 2006

Cobalt (cyclam) complex has been successfully immobilized onto SBA-15, and proven to be an active catalyst for the epoxidation of styrene with tert-butyl hydroperoxide as a terminal oxidant. The selectivity for styrene oxide was observed to be up to 66% with 40% styrene conversion after 12h reaction time. The reversible redox cycle between Co(III) and Co(II) couple which was supposed to play key role during the epoxidation reaction was supported by a cyclic voltametry analysis. The textural properties of the catalyst was characterized by XRD, N2 adsorption-desorption, and TEM analysis.

• Applied Science and Convergence Technology
• /
• v.27 no.2
• /
• pp.38-41
• /
• 2018

We demonstrate the growth of a sheet-like ZnO membrane on ZnO nano rod layers. The growth process is composed of 3 steps of ZnO seed formation, ZnO nano rod growth and sheet-like ZnO membrane formation on those nano rods. To confirm the fundamental growth mechanism, the lattice structures of each step were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM) measurement. Analysis of the relation between the texture coefficient and the surface shape of the ZnO membrane on the ZnO nano rods shows that the surface morphology of ZnO nano structures can be controlled using the temperature of the growing solution and the concentration of the chemical solution.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.304-307
• /
• 2012

Nano-fibers of LiFePO4 were synthesized from a metal oxide precursor by adopting electrospinning method. After calcination of the above precursor nano-fibers at 800 ℃, LiFePO4 nano-fibers with a diameter of 300 ~ 800 nm, were successfully obtained. Measurement were performed using X-ray diffraction (XRD), fourier transform infrared spectrometer (FT-IR), videoscope, scanning electron microscope (SEM) and atomic force microscope (AFM), respectively, were performed to characterize the properties of the as-prepared materials. The results showed that the crystalline phase and morphology of the fibers were largely influenced the starting materials and electrospinning conditions.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.21-29
• /
• 2004

Hot carrier degradation characteristics of Nano-scale CMOSFETs with dual gate oxide have been analyzed in depth. It is shown that, PMOSFET lifetime dominate the device lifetime than NMOSFET In Nano-scale CMOSFETs, that is, PMOSFET lifetime under CHC (Channel Hot Carrier) stress is much lower than NMOSFET lifetime under DAHC (Dram Avalanche Hot Carrier) stress. (In case of thin MOSFET, CHC stress showed severe degradation than DAHC for PMOSFET and DAHC than CHC for NMOSFET as well known.) Therefore, the interface trap generation due to enhanced hot hole injection will become a dominant degradation factor in upcoming Nano-scale CMOSFET technology. In case of PMOSFETs, CHC shows enhanced degradation than DAHC regardless of thin and thick PMOSFETs. However, what is important is that hot hole injection rather than hot electron injection play a important role in PMOSFET degradation i.e. threshold voltage increases and saturation drain current decreases due to the hot carrier stresses for both thin and thick PMOSFET. In case of thick MOSFET, the degradation by hot carrier is confirmed using charge pumping current method. Therefore, suppression of PMOSFET hot carrier degradation or hot hole injection is highly necessary to enhance overall device lifetime or circuit lifetime in Nano-scale CMOSFET technology

• Bulletin of the Korean Chemical Society
• /
• v.33 no.1
• /
• pp.189-193
• /
• 2012

ZnO nanorods were grown on the $Cd_xZn_{1-x}O$ seed layers with various Cd mole fractions by hydrothermal method. The effects of the Cd mole fraction for $Cd_xZn_{1-x}O$ seed layers on the structural and optical properties of the ZnO nanorods were investigated by scanning electron microscopy, X-ray diffraction, and photoluminescence. The narrowest full-width at half-maximum and largest grain size of the $Cd_xZn_{1-x}O$ seed layers, indicating improvement in crystal quality, were observed at the Cd mole fraction of 0.5. At the Cd mole fraction of 0.5, the largest enhancement in the density, the crystal quality, and the growth rate of the ZnO nanorods was observed while their appearance was not affected significantly by the incorporation of the Cd in the $Cd_xZn_{1-x}O$ seed layers. Consequently, the luminescent properties of the ZnO nanorods were enhanced. The largest improvement in the structural and optical properties of the ZnO nanorods was observed at the Cd mole fraction of 0.5.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.203.1-203.1
• /
• 2013

Zinc oxide (ZnO) nanocrystalline thin films on various growth temperatures for active layer and different buffer layer thickness were grown by plasma-assisted molecular beam epitaxy (PA-MBE) on Si substrates. The ZnO active layer were grown with various growth temperature from 500 to $800^{\circ}C$ and the ZnO buffer layer were grown for different time from 5 to 40 minutes. To investigate the structural and optical properties of the ZnO thin films, scanning electron microscope (SEM), X-ray diffractometer (XRD), and photoluminescence (PL) spectroscopy were used, respectively. In the SEM images, the ZnO thin films have high densification of grains and good roughness and uniformity at $800^{\circ}C$ for active layer growth temperature and 20 minutes for buffer layer growth time, respectively. The PL spectra of ZnO buffer layers and active layers display sharp near band edge (NBE) emissions in UV range and broad deep level emissions (DLE) in visible range. The intensity of NBE peaks for the ZnO thin films significantly increase with increase in the active layer growth temperature. In addition, the NBE peak at 20 minutes for buffer layer growth time has the largest emission intensity and the intensity of DLE peaks decrease with increase in the growth time.

• Current Photovoltaic Research
• /
• v.12 no.2
• /
• pp.37-40
• /
• 2024

One of the current innovation trends in the solar industry is the increase in the size of silicon wafers. As the wafer size increases, the series resistance of the module rises, highlighting the need for research on methods for cutting and bonding solar cells. Among these, the Infrared (IR) laser scribing technique has been extensively researched. However, there is still insufficient optimization research regarding the thermal damage caused by lasers on the Transparent Conductive Oxide (TCO) layer of Heterojunction (HJT) solar cells. Therefore, in this study, we systematically varied conditions such as IR laser scribing speed, frequency, power, and the number of scribes to investigate their impact on the performance of cut cells under each condition. Additionally, we conducted a comparative analysis of thermal damage effects on the TCO layer based on varying scribing depths.