• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.6
• /
• pp.399-405
• /
• 2015

In this work we use the mode decomposition technique employing chirplet transform, which is able to separate the individual modes from dispersive and multimodal waveform measured with the magnetostrictive sensor. The mode decomposition technique is also used to estimate the time-frequency centers and individual energies of the reflection, which would be used to locate and characterize axial defects. The arrival times of the separated modes are calculated and the axial defect lengths can be evaluated by using the estimated arrival time. Results from an experiment on a carbon steel pipe are presented and it is shown that the accurate and quantitative defect characterization could become enabled using the proposed technique.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.184-186
• /
• 1999

This paper presents a method for security constrained optimal reactive power planning in electric power systems. This method deals with corrective mode optimal reactive power dispatch in each (n-1)contingency system state and determination of the location and amount of reactive sources in preventive mode. In this paper the proposed scheme uses Benders decomposition method to determine the proper amount and location of reactive support in order to maintain a proper voltage profile and minimize active power transmission losses. This method is tested on IEEE 30 bus test system to prove effectiveness.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.4
• /
• pp.585-592
• /
• 2003

Among various sensitivity evaluation techniques, semi-analytical method(SAM) is quite popular since this method is more advantageous than analytical method(AM) and global finite difference method(FDM). However, SAM reveals severe inaccuracy problem when relatively large rigid body motions are identified fur individual elements. Such errors result from the numerical differentiation of the pseudo load vector calculated by the finite difference scheme. In the present study, an iterative method combined with mode decomposition technique is proposed to compute reliable semi-analytical design sensitivities. The improvement of design sensitivities corresponding to the rigid body mode is evaluated by exact differentiation of the rigid body modes and the error of SAM caused by numerical difference scheme is alleviated by using a Von Neumann series approximation considering the higher order terms for the sensitivity derivatives.

• Smart Structures and Systems
• /
• v.2 no.2
• /
• pp.171-188
• /
• 2006

This paper deals with damage detection using active Lamb waves. The wavelet transform and empirical mode decomposition methods are discussed for measuring the Lamb wave's arrival time of the group velocity. An experimental system to diagnose the damage in the composite plate is developed. A method to optimize this system is also given for practical applications of active Lamb waves, which involve optimal arrangement of the piezoelectric elements to produce single mode Lamb waves. In the paper, the single mode Lamb wave means that there exists no overlapping among different Lamb wave modes and the original Lamb wave signal with the boundary reflection signals. Based on this optimized PZT arrangement method, five damage localizations on different plates are completed and the results using wavelet transform and empirical mode decomposition methods are compared.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.257-264
• /
• 2010

Generally, estimations on the displacement as an important factor in evaluating the safety of large structures could be a barometer assessing whether the condition of the structure is deteriorating. Practically, it is not easy how to measure the displacement response to large structures like suspension bridges. In this study, as a method for estimation displacement response from strain signals, mode decomposition technique is proposed. Total displacement response is estimated by superposing quasistatic displacement response and modal displacement responses in dominant modes with larger contributions after estimating the modal displacement responses. If foiled strain gauges are used to measure strain signals, there would likely to generate electric noise, what's more, the more measuring points there are the more economic burden it could be. In order to solve such problems, fiber optic bragg-grating(FBG) sensors were used, which have multi-point measurements with no effect on electric noises. Therefore, the experiment was performed through dynamic load test of suspension bridge and plate-girder bridge to review the possibility for using mode decomposition technique.

• Wind and Structures
• /
• v.37 no.6
• /
• pp.445-460
• /
• 2023

Accurate estimation of modal parameters (i.e., natural frequency, damping ratio) of tall buildings is of great importance to their structural design, structural health monitoring, vibration control, and state assessment. Based on the combination of variational mode decomposition, smoothed discrete energy separation algorithm-1, and Half-cycle energy operator (VMD-SH), this paper presents a method for structural modal parameter estimation. The variational mode decomposition is proved to be effective and reliable for decomposing the mixed-signal with low frequencies and damping ratios, and the validity of both smoothed discrete energy separation algorithm-1 and Half-cycle energy operator in the modal identification of a single modal system is verified. By incorporating these techniques, the VMD-SH method is able to accurately identify and extract the various modes present in a signal, providing improved insights into its underlying structure and behavior. Subsequently, a numerical study of a four-story frame structure is conducted using the Newmark-β method, and it is found that the relative errors of natural frequency and damping ratio estimated by the presented method are much smaller than those by traditional methods, validating the effectiveness and accuracy of the combined method for the modal identification of the multi-modal system. Furthermore, the presented method is employed to estimate modal parameters of a full-scale tall building utilizing acceleration responses. The identified results verify the applicability and accuracy of the presented VMD-SH method in field measurements. The study demonstrates the effectiveness and robustness of the proposed VMD-SH method in accurately estimating modal parameters of tall buildings from acceleration response data.

• Wind and Structures
• /
• v.32 no.3
• /
• pp.227-238
• /
• 2021

This study analyzed the pressure patterns and local pressure of tall buildings with corner modifications (recessed and chamfered corner) using wind tunnel tests and proper orthogonal decomposition (POD). POD can distinguish pressure patterns by POD mode and more dominant pressure patterns can be found according to the order of POD modes. Results show that both recessed and chamfered corners effectively reduced wind-induced responses. Additionally, unique effects were observed depending on the ratio of corner modification. Tall building models with recessed corners showed fluctuations in the approaching wind flow in the first POD mode and vortex shedding effects in the second POD mode. With large corner modification, energy distribution became small in the first POD mode, which shows that the effect of the first POD mode reduced. Among building models with chamfered corners, vortex shedding effects appeared in the first POD mode, except for the model with the highest ratio of corner modifications. The POD confirmed that both recessed and chamfered corners play a role in reducing vortex shedding effects, and the normalized power spectral density peak value of modes showing vortex shedding was smaller than that of the building model with a square section. Vortex shedding effects were observed on the front corner surfaces resulting from corner modification, as with the side surface. For buildings with recessed corners, the local pressure on corner surfaces was larger than that of side surfaces. Moreover, the average wind pressure was effectively reduced to 88.42% and 92.40% in RE1 on the windward surface and CH1 on the side surface, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.1
• /
• pp.6-14
• /
• 2011

This paper presents a high-speed QR decomposition architecture for the multi-input-multi-output (MIMO) receiver based on Givens rotation. Under fast-varying channel, since the inverse matrix calculation has to be performed frequently in MIMO receiver, a high performance and low latency QR decomposition module is highly required. The proposed QR decomposition architecture is composed of Sign-Select Lookahead (SSL) coordinate rotation digital computer (CORDIC). In the SSL-CORDIC, the sign bits, which are computed ahead to select which direction to rotate, are used to select one of the last iteration results, therefore, the data dependencies on the previous iterations are efficiently removed. Our proposed QR decomposition module is implemented using TSMC 0.25 ${\mu}M$ CMOS process. Experimental results show that the proposed QR architecture achieves 34.83% speed-up over the Compact CORDIC based architecture for the 4 ${\times}$ 4 matrix decomposition.

• IEIE Transactions on Smart Processing and Computing
• /
• v.5 no.5
• /
• pp.366-373
• /
• 2016

This paper proposes a pre-processing algorithm to improve the coding efficiency of perceptual video coding. First, an input image is decomposed into multiple sub-bands through linear sub-band decomposition. Then, the sub-bands that have low visual sensitivity are suppressed by assigning small gains to them. Experimental results show that if the proposed algorithm is adopted for pre-processing in a High Efficiency Video Coding (HEVC) encoder, it can provide significant bit-saving effects of approximately 12% in low delay mode and 9.4% in random access mode.

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.475-482
• /
• 2022

Signal pre-processing and post-processing are some areas of study around electrical resistance tomography due to the low spatial resolution of pixel-based reconstructed images. In addition, methods that improve integrity and noise reduction are candidates for application in ERT. Lately, formulations of image processing methods provide new implementations and studies to improve the response against noise. For example, compact variational mode decomposition has recently shown good performance in image decomposition and segmentation. The results from this first approach of C-VMD to ERT show an improvement due to image segmentation, providing filtering of noise in the background and location of the target.