• 펄프종이기술
• /
• 제35권4호
• /
• pp.8-16
• /
• 2003

The objective of this study was to investigate the potential application of the separated refining system in the papermaking process using cotton pulps. The cotton staple and linter fibers were expected to show a great difference in their refining responses due to their morphological and physical differences. Experiments were conducted to examine the differences in flocculation tendency, CED viscosity, fiber length, handsheet properties and the SEM surface images between staple and linter fibers at a given refining degree. These fibers were also subjected to separated refining in a laboratory-scale beater and in a mill-scale refiner as well. The effect of the separated refining on the refining rates and papermaking properties were evaluated. Results obtained are summarized as follows: 1. Fiber flocculation tendency of cotton staple was estimated to be significantly greater than that of linter fibers; 2. The staple fibers showed higher cellulose DP, longer fiber length and higher sheet strength at a given refining degree compared to linter fibers, but remarkably slower refining rate was observed; 3. The separated refining system exhibited a significant increase in sheet strengths, especiauy in folding endurance, with an increase in the fibrillation on the surface of staple fibers, but slightly lower or comparable fiber length after refining to the mixed refining system; 4. Similar results were also obtained from the machine trial in which about 7-8％ energy saving effects were achived in the separated refining system. On the basis of the results observed in this study, it was concluded that a significant increase in paper strength and a substantial reduction in refining energy consumption could be achieved using the separated refining system for the cotton staple and linter fiber stock refining.

• Journal of Microbiology
• /
• 제43권5호
• /
• pp.463-468
• /
• 2005

Studying the bacteria of hazardous insects allows the opportunity to find potentially better biological control agents. Therefore, in this study, bacteria from summer chafer (Amphimallon solstitiale L., Coleoptera: Scarabaeidae) we isolated and identified the insecticidal effects of bacteria isolated from A. solstitiale and Melolontha melolontha L. (common cockchafer, Coleoptera: Scarabaeidae) and the mixtures of these bacterial isolates were investigated on A. solstitiale larvae. Crystals from Bacillus sp. isolated from M. melolontha were also purified, and tested against the second and third-stage larvae of A. solstitiale. The bacterial isolates of A. solstitiale were identified as Pseudomonas sp., Pseudomonas sp., Bacillus cereus and Micrococcus luteus, based on their morphology, spore formation, nutritional features, and physiological and biochemical characteristics. The insecticidal effects of the bacterial isolates determined on the larvae of A. solstitiale were $90\%$ with B. cereus isolated from A. solstitiale, and $75\%$ with B. cereus, B. sphaericus and B. thuringiensis isolated from M. melolontha within ten days. The highest insecticidal effects of the mixed infections on the larvae of A. solstitiale were $100\%$ both with B. cereus+B. sphaericus and with B. cereus+B. thuringiensis. In the crystal protein bioassays, the highest insecticidal effect was $65\%$ with crystals of B. thuringiensis and B. sphaericus isolated from M. melolontha within seven days. Finally, our results showed that the mixed infections could be utilized as microbial control agents, as they have a $100\%$ insecticidal effect on the larvae of A. solstitiale.

• 한국동물위생학회지
• /
• 제44권3호
• /
• pp.141-148
• /
• 2021

The objective of this research was to evaluate the immune response to Salmonella Gallinarum experimentally infected layers fed with Guanosine 5'-monophosphate-chelated calcium and iron feed additives. Hy-Line brown, 34 week-olds layers were assigned to 3 groups; Group 1: basal diet feed, Group 2 (CaFe-GMP): basal diet feed mixed with chelated calcium and iron, and Group 3 (Fe-OCHT): basal diet feed mixed with chitosan for 4 weeks. There were challenged with 1.0×10⁸ CFU/mL of the cultured Salmonella Gallinarum (SG) by oral administration on 28th feeding days. After SG challenge, Flow cytometric profiles showed that the CD4+/CD8+ T lymphocyte activation of Group 2 was much higher than Group 1 and Group 3 (P<0.05). In addition, the levels of interleukin-2 (13.37 mg/dl) and interferon-γ (2.35 mg/dl) in Group 2 were higher than Group 1 and Group 2. Populations of Lactic acid bacteria (3.5×10¹⁰ CFU/g) from cecum was highest observed in group 2. Re-isolation of SG from cecum in group 2 (8×10⁵ CFU/g) was lower than group 1 (1.83×10¹⁰ CFU/g). The result of this study demonstrated that CaFe-GMP feed additive may be one of the potential candidates to control salmonellosis and functional feeds in layers.

• Geomechanics and Engineering
• /
• 제18권5호
• /
• pp.535-543
• /
• 2019

Building on/with expansive soils with no treatment brings complications. Compacted expansive soils specifically fall short in satisfying the minimum requirements for transport embankment infrastructures, requiring the adoption of hauled virgin mineral aggregates or a sustainable alternative. Use of hauled aggregates comes at a high carbon and economical cost. On average, every 9m high embankment built with quarried/hauled soils cost $12600MJ.m^{-2}$ Embodied Energy (EE). A prospect of using mixed cutting-arising expansive soils with industrial/domestic wastes can reduce the carbon cost and ease the pressure on landfills. The widespread use of recycled materials has been extensively limited due to concerns over their long-term performance, generally low shear strength and stiffness. In this contribution, hydromechanical properties of a waste tyre sand-sized rubber (a mixture of polybutadiene, polyisoprene, elastomers, and styrene-butadiene) and expansive silt is studied, allowing the short- and long-term behaviour of optimum compacted composites to be better established. The inclusion of tyre shred substantially decreased the swelling potential/pressure and modestly lowered the compression index. Silt-Tyre powder replacement lowered the bulk density, allowing construction of lighter reinforced earth structures. The shear strength and stiffness decreased on addition of tyre powder, yet the contribution of matric suction to the shear strength remained constant for tyre shred contents up to 20%. Reinforced soils adopted a ductile post-peak plastic behaviour with enhanced failure strain, offering the opportunity to build more flexible subgrades as recommended for expansive soils. Residual water content and tyre shred content are directly correlated; tyre-reinforced silt showed a greater capacity of water storage (than natural silts) and hence a sustainable solution to waterlogging and surficial flooding particularly in urban settings. Crushed fine tyre shred mixed with expansive silts/sands at 15 to 20 wt% appear to offer the maximum reduction in swelling-shrinking properties at minimum cracking, strength loss and enhanced compressibility expenses.

• 대한의생명과학회지
• /
• 제25권3호
• /
• pp.247-255
• /
• 2019

Curcuma longa L. (C.L), Curcuma aromatica Salisb. (C.A) and Zingiber officinale Rosc. (Z.O) of Zingiberaceae plants which are well known as effects of natural anti-oxidant, anti-cancer and anti-inflammatory. We examined that the Zingiberaceae plants are involved in development and modulation of orofacial pain in rats. Male, 7- to 8-week-old, Sprague-Dawley rats weighing 240~280 g were used in this study. Experiments were performed using acute pain model that was caused by the injection of 5% formalin into the right vibrissa pad. The number of scratching or rubbing to the injection site was recorded for 9 consecutive 5-minute intervals following injection of formalin. The experimental groups were acute orofacial inflammatory pain; control group (formalin, 5%), vehicle group (5% formalin after sodium carboxymethyl cellulose), single administration group, single mixed administration group, repeated administration group. The experiments were performed various concentrations of Zingiberaceae plants extract. Therefore, oral administration of C.L, C.A, and Z.O (p.o., concentrations of 12.5, 25 mg/mL) in orofacial inflammatory pain model substantially decrease the nociceptive behavior in a concentration dependent manner. And it tended to decrease at low concentration (12.5 mg/mL) of single mixed and repeated administration more than single administration. This result means that Zingiberaceae plants extract affects the modulation of acute orofacial inflammatory pain. Thus, Zingiberaceae plants extract may be a potential therapeutic treatment for orofacial inflammatory pain.

• 멤브레인
• /
• 제30권6호
• /
• pp.385-394
• /
• 2020

기체분리공정에서 사용되는 분리막은 높은 기체 투과 및 분리성능과 고온·고압 조건에서 높은 안정성을 보여야 한다. 하지만 고분자분리막(특히, 유리상 고분자)은 응축 가능한 기체 분자(예를 들어, CO2, H2S, hydrocarbon 등)에 노출되면 고분자 사슬이 부풀어 오르는 가소화 현상을 보여 안정성 측면에서 한계를 보인다. 이러한 가소화 현상은 고압의 복합기체 분리공정에서 선택도를 감소시켜 장기적으로는 고분자분리막이 분리공정에 도입될 수 없는 문제를 가져온다. 이러한 가소화 현상 문제를 해결하기 위해서 분리막 연구자들은 분리막 열처리, 고분자 혼합, 고분자구조의 열적 재배열, 혼합매질분리막 제작, 가교화 방법 등을 통하여 분리막의 가소화 저항을 향상시켰다. 본 총설에서는 고분자 분리막의 가소화 저항의 개념 및 현상에 대해서 알아보고 이를 해결할 수 있는 인자들과 그와 연관된 연구들을 살펴보도록 할 것이다.

• 멤브레인
• /
• 제30권6호
• /
• pp.450-459
• /
• 2020

분리막 기반 공정은 기존 공정에 비해 에너지 소비 및 환경 영향을 감소시킬 수 있는 잠재력을 갖고 있다. 분리막 공정의 성능은 분리막의 투과 특성과 직결되기 때문에, 선택도와 투과도가 우수한 새로운 분리막 소재를 개발하기 위해 많은 연구가 진행되어 왔다. 본 연구에서는 기체 투과선택성 향상을 위해 부피가 큰 에틸 치환기를 포함하는 diamine 단량체인 4,4'-methylenebis(2,6-diethylaniline) (MDEA)을 도입한 폴리이미드를 합성한 후 그 특성을 관찰하고 기체 투과 특성을 조사하였다. 이미드링 질소의 오쏘에 위치한 에틸기는 고분자 사슬의 패킹을 방해하고 사슬 강성과 고분자 사슬 간 거리를 증가시켰다. MDEA 기반 폴리이미드 분리막의 기체 투과 특성을 조사한 결과, 프로필렌/프로판 선택도 14.5와 프로필렌 투과도 7.0 barrer의 결과를 얻었다. 부피가 큰 치환기로 인해 기체 확산 길이가 증가하여 기체 투과 선택성이 높아졌음을 확인하였다. 혼합 기체 투과 결과 또한 MDEA 기반 폴리이미드 분리막이 실제 혼합 기체 공정에서 높은 선택도를 달성할 수 있다는 것을 보여준다. 이러한 MDEA 기반 폴리이미드는 우수한 투과도 및 선택도로 경제적인 프로필렌 분리의 가능성을 크게 높일 수 있다.

• International Journal of Computer Science & Network Security
• /
• 제22권1호
• /
• pp.305-311
• /
• 2022

This research aimed to provide a profound description of the practices of social media users in the Kingdom of Saudi Arabia (KSA), specifically the users of Facebook^® (FB) and Snapchat^® (SC), the reasons for these practices, decisions made, and the people involved. Such research would be of significant help to designers and policymakers of social media applications in understanding user practices when using social media applications and the reasons for such practices in the KSA. This better comprehension would be of significant help in improving current applications and creating new ones. According to the data analysis, there was a clear preference for SC over FB in the KSA. Most participants with SC accounts were described as very active users, accessing their accounts at least once a day compared to FB users. The users were led by this high preference for SC to create new words derived from the name of the application and use them in daily life. We showed our experience of carrying out a study in which the main objective was to collect factual empirical data from participants about their daily usage of social media applications while considering the unique cultural settings in the KSA. Mixed quantitative and qualitative methods were used to triangulate the data, increasing its trustworthiness and validity. Multiple perspectives were obtained using various data collection methods. Therefore, conclusions would not be confounded with limitations of any particular methodology or with conditions of any collection rounds. This research would constitute a valuable guide for researchers intending to use methods with male and female informants from different cultures, preparing them for potential challenges and suggesting possible solutions.

• Composite Materials and Engineering
• /
• 제3권3호
• /
• pp.201-220
• /
• 2021

In this study, potential of three machine learning techniques i.e., M5P, Support vector machines and Gaussian processes were evaluated to find the best algorithm for the prediction of flexural strength of concrete mix with steel fibre. The study comprises the comparison of results obtained from above-said techniques for given dataset. The dataset consists of 124 observations from past research studies and this dataset is randomly divided into two subsets namely training and testing datasets with (70-30)% proportion by weight. Cement, fine aggregates, coarse aggregates, water, super plasticizer/ high-range water reducer, steel fibre, fibre length and curing days were taken as input parameters whereas flexural strength of the concrete mix was taken as the output parameter. Performance of the techniques was checked by statistic evaluation parameters. Results show that the Gaussian process technique works better than other techniques with its minimum error bandwidth. Statistical analysis shows that the Gaussian process predicts better results with higher coefficient of correlation value (0.9138) and minimum mean absolute error (1.2954) and Root mean square error value (1.9672). Sensitivity analysis proves that steel fibre is the significant parameter among other parameters to predict the flexural strength of concrete mix. According to the shape of the fibre, the mixed type performs better for this data than the hooked shape of the steel fibre, which has a higher CC of 0.9649, which shows that the shape of fibers do effect the flexural strength of the concrete. However, the intricacy of the mixed fibres needs further investigations. For future mixes, the most favorable range for the increase in flexural strength of concrete mix found to be (1-3)%.

• Journal of the Korean Wood Science and Technology
• /
• 제51권1호
• /
• pp.23-37
• /
• 2023

One type of biomass that has promising potential for bio pellet production is spent coffee grounds (SCGs). However, previous studies have shown that SCGs in bio pellets cause a lot of smoke. Therefore, they need to be mixed with a material that has a higher calorific value to produce better quality pellets. One material that can be used is pine wood because it has a natural resin content that can increase the calorific value. The aim of this study was to examine the quality of bio pellets produced with SCGs and pine wood charcoal at different particle sizes. The charcoal was ground using either a hammer mill (HM) or a ball mill (BM). Pine wood charcoal was mixed with SCGs at ratios of SCGs to pine wood charcoal of 4:6 and 6:4 by weight, respectively, and the adhesive used a tapioca with a composition ratio 5% of the raw material. The bio pellets were produced using a manual pellet press. The quality of the bio pellets was assessed based on Indonesian National Standard (SNI) 8021-2014, and the physical observations include flame length, burning rate, and compressive strength. The average water content, ash content, and calorific value of the bio pellets were in accordance with SNI 8021-2014, but the density and ash content values were below the standard values. The BM variation of bio pellets had a higher compressive strength than the HM variation, and the 4:6 BM variation had the longest burning time compared with 4:6 HM.